Honda Bmw 5 Service Manual
Have a look at the manual Honda Bmw 5 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 328 Honda manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
-- I I: ... . -. Rear Suspension! -- .- - Air compressor pump relay, removing and installing - Working in cargo compartment, remove spare wheel. 4 Remove air supply pump fasteners (arrows). Turn pump over. - Turn relay plug 45 and remove relay. EHC control module, removing and installing The EHC control module is mounted on the right side of the spare tire well in the cargo compartment. - Remove spare tire. 4 Remove electrical components cover (A). - Release control module wiring harness plug loclting clip (B) and remove module. - Installation is reverse of removal. - After assembly, reset ride height using BMW diagnostic scan tool DIS. Air supply unit, removing and installing CAUTION- Maintain high levels of cleanliness around air line connec- tions when disassembling and assembling air suspension components. Even small dirt particles can cause leakage in the pressurized system. When the airsupply unit is removed for any reason, reset ride height using BMW scan tools DIS or MoDiC. - Remove spare tire. i~B,!n,,ayPubi.l,c~u.c~~-A~~ R
Rear Suspension 4 Remove air line fittings (A) from bottom of air distribution con- nectors. Cut off wire ties. WARNING- Vehicle will lower when the air pipes are opened. 4 Rotate air line distribution connector (A) 45 in direction of arrow to remove. Rotate electrical connector (B) 45 in direction of arrow to remove. Compress wiring connector locking clips (arrows) and dis- connect wiring harness. < Remove air supply unit mounting fasteners (arrows) and re- move unit. - Installation is reverse of removal. When installing air lines always match line colors. a After assembly, reset ride height using BMW diagnostic scan tool DIS.
330-47 Rear suspension/ Ride height sensor, removing and installing Hall effect sensors for vehicle height detection are mounted on the left and right sides of the rear suspension. A coupling rod mounted between the rear suspension arm and the sen- sor arm is used to send a varying voltage signal to the EHC control module. Raise car and support safely. WARNING- Male sure the car is firmly supported on jaclc stands de- signed for the purpose. Place jaclc stands underneath struc- tural chassis points. Do not place jaclc stands under sus~ension Darts. Working underneath rear of car, remove trim panel (arrow) just ahead of suspension subframe. Disconnect electrical harness connector from sensor. 4 Remove control rod mounting nut (arrow).Turn control rod to access sensor mounting fastener. - Remove sensor mounting fasteners. - Remove ride height sensor. - Installation is reverse of removal. Make sure sensor lever points outward. After assembly, re- set ride height using BMW diagnostic scan tool DIS. Tightening torques Ride height sensor to bracket 5 Nrn (44 lb-in) Lever to height sensor 9 Nrn (80 ib-in)
33UFinal Drive General ........................... ,331 -2 Drive Axles ....................... 331 -1 4 Special tools ........................ ,331 -2 Drive axle assembly ................. 331-14 Aluminum suspension components ...... ,331-4 Drive axle, removing and installing (sedan) .................... 331-14 ........................ Final Drive ,331 -5 Drive axle, removing ........... ...... Final drive, removing and installing ,331-5 and (Sport Wagon) 331-15 ...................... Differential oil level, checking ........... ,331-6 CV joint boots 331-17 Final drive in~ut shaft seal, replacing ..... ,331-7 . Final drive oitput shaft seals, replacing . . ,331-10 Final drive cover, removing and installing ,331-12 Final drive mounts, replacing .......... ,331-12
331-2 Final Drive This repair group covers removal and repair informat~on for the final drive (differential), axle shafts. CV joints, CV joint boots, and final drive seal replacement. Internal repairs of the differential assembly are not covered in this manual. Special tools BMW recommends some special tools for the removal of the drive axles as well as the installation of rear differential input and output drive flange seals. Some common pullers and drifts can often be substituted for these tools. 4 Drive flange holder (Tool No. BMW 2 30 020) < Drive flange puller (ToolNo.BMW31 2101 131 2102131 2103131 2104) < Drive pinion set (Tool No. BMW 33 1 340) 4 Clamp~ng tool set (ToolNo.BMW332101 13321021332103)
Final Drive 4 Output shaft tool set (ToolNo. BMW332111 1332114/332115/3321161 33211713321181332119) 4 Trailing arm tool set 11 (Tool NO BMW 33 3 331 I 33 3 332 1 33 3 333 133 3 334) 4 Final drive mount set (ToolNo. BMW334151 /334152/334153/334154/ 3341551334156133415713341581334159) < Differential mount press set (Tool No.BMW334161 1334162133416413341651 33 4 166) 33 4 161 Q Differential mount press set (ToolNo. BMW334171 /334172/334173/3341 174) . . 33 4 181 4 Differential mount press set 33 (Tool No. BMW334181 133418213341831334184) Support tube set (ToolNo.BMW334191133419213341931334194) 33 4 192 33 4 191
331-4 Final Drive 4 Final drive output shaft seal tool (Tool No. BMW 33 4 250) 4 Pulling set (Tool No. BMW 33 4 401 / 33 4 402 / 33 4 403 133 4 404 / 33 4 405 / 33 4 406) Aluminum suspension components In order to reduce vehicle weight, aluminum suspension com- ponents are ~sed in some models. A tesl wlh a magnet wi.1 easly reveal lhe metal Lseo. If working with a umin~m com- ponents, be sure to read and follow the cautions below. CAUTIOI\C Due to the chemical and corrosion characteristics of alumi- num, do not bring into contact with battery acid. Do not use wire brushes with brass or iron bristles. Only use brushes with stainless steel bristles. Do not expose to flying sparks from grinding/cutting op- erations. Do not subject to steel welding splashes. Do not expose to temperatures over 80°C (176F), even for short periods. Temperatures in painting facili- ties are not a problem.
Final Drive Final drive, removing and installing - Raise rear of car. WARNING- Make sure that the car is firmly supported on jack stands de- signed for the purpose. Place the jaclc stands beneath struc- tural chassis ~oints. Do not i lace iaclc stands under ( suspension barfs. Remove exhaust system. See 180 Exhaust System. Disconnect drive shaft from final drive. See 260 Driveshaft. Remove drive axle CV joint bolts (arrows) at left and right sides. Suspend drive axles from body using stiff wire. 4 Support final drive with BMW special tool 33 4 390. * Remove front final drive mounting bolt. Remove rear final drive mounting bolts (2). Carefully lower final drive unit. - To install, use BMW special tool 33 4 390 to lift final drive into place. CA UTIOP& The following sequence must be used when installing the fi- nal drive to prevent torsion stress on the final drive during in- Install mounting bolts and finger tighten only. Remove final drive support. Tighten both rear mounting bolts. Tighten front mounting bolt. NOTE- Use new self-locking nuts. - Check differential oil level. See Differential oil level, check- ing. - Remainder of installation is reverse of removal.
Final Drive Tightening torques F~nal drive to rear axle carrier 105 Nm (77 it-lb) Driveshaft CV joint to final drive flange - MlO (Torx bolt) 70 Nm (51 ft-lb) - M8 (compression nut) 32 Nm (24 ft-lb) Drive axle to final drive ilange Torx bolts (M10) 83 Nm (61 ft-lb) Torx bolt with rlbbed teeth (M10) 64 Nm (47 ft-lb) Torx bolt wlth ribbed teeth (MI0 sliver) 80 Nm (59 ft-lb) Torx bolt with ribbed teeth (M10 black) 100 Nm (74 ft-lb) * Torx bolt with ribbed teeth (M12) 135 Nm (100 ft-lb) Differential oil level, checking The E39 differential is filled with lifetime oil that ordinarily does not need to be changed. BMW recommends using only a specially formulated synthetic gear oil (SAF-XO) that is available through an authorized BMW dealer parts depart- ment. For additional information on this lubricant and any oth- er lubricants that may be compatible, contact an authorized BMW dealer service department. < Check rear differential oil level at filler plug (arrow). - Check lubricant level with car on a level surface: Level is correct when fluid just reaches edge of filler hole. If necessary, top up fluid. * Replace filler plug sealing ring. Install and tighten oil filler plug when oil level is correct. NOTE- Use either a 14 mm or 17 mm Allen socket to remove the drain plug. If car is raised in the air. it should be level when checkino or filling final drive fluid level. - Tightening torque - Filler plug to final drive housing 70 Nm (52 ft-lb) -