GE Vivid 7 Service Manual
Have a look at the manual GE Vivid 7 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 45 GE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
GE HEALTHCARE DIRECTION FC091194, REVISION 11 VIVID 7 SERVICE MANUAL Chapter 3 - System Setup 3 - 47 3-9-5-3 Change AE Title and/or Port Number (Port No.) NOTE: You don’t need to use the Modify butt on when changing AE Title and/or Port No. 1.) To change AE Title and/or Port No ., edit the respective fields. 2.) Select Save settings to store your changes. This will bring up a new Warning screen. 3.) Select Ok to save your changes or Cancel to return without saving any changes. 4.) Reboot Vivid 7 to activate the settings or continue with other Tcpip set-up tasks. Figure 3-36 AE Title and Port No. Figure 3-37 Warning
GE HEALTHCARE DIRECTION FC091194, REVISION 11 VIVID 7 SERVICE MANUAL 3 - 48 Section 3-9 - Connectivity Setup - Software v7.x (BT’08), v6.x, v5.x and v4.x 3-9-6 Set the Scanner’s Ne twork Information - S/W v4.2/v5.2/v6.1/v7.x and later NOTE: For software version v4.0/v4.1/v5.0/v5.1/v6.0, see: 3-9-7 Set the Scanner’s Network Information - S/W v4.0/v4.1/v5.0/v5.1/v6.0 on page 3-50 . 1.) When in the Tcpip (TCP/IP) screen, select Advanced Settings to display the Network Connections screen. 2.) Right-click Local Area Connection and select Properties from the pop-up menu . This will display the Local Area Connection Properties screen. Figure 3-38 Select Advanced Settings Figure 3-39 Network Connections screen ADVANCED SETTINGS
GE HEALTHCARE DIRECTION FC091194, REVISION 11 VIVID 7 SERVICE MANUAL Chapter 3 - System Setup 3 - 49 3-9-6 Set the Scanner’s Ne twork Information - S/W v4.2/v5.2/v6.1/v7.x and later (cont’d) 3.) Select (highlight) Internet Protocol (TCP/IP) and select Properties to display the Internet Protocol (TCP/IP) Properties screen. The Internet Protocol (TCP/IP) Properties screen is used to set the following parameters: If using DHCP Check the Obtain an IP address automatically check box. If not using DHCP 1.) Uncheck the Obtain an IP address automatically check box, and enter the: - IP Address for Vivid 7. (Default IP Ad dress setting from factory: 10.0.0.3). - Subnet Mask for Vivid 7. (Default Subnet Ma sk setting from factory: 255.255.255.0). - IP address for Default Gateway. (Default Gatewa y setting from factory IP address: 0.0.0.0). 2.) Select OK to keep your changes or Cancel to close the Internet Protocol (TCP/IP) Properties screen without keeping any changes. 3.) Select OK to close (and save) the Local Area Connection Properties dialog. 4.) Select the “x” in the upper right corner to close the Network Connections window. Figure 3-40 Local Area Connection Properties Figure 3-41 Internet Protocol (TCP/IP) Properties screen
GE HEALTHCARE DIRECTION FC091194, REVISION 11 VIVID 7 SERVICE MANUAL 3 - 50 Section 3-9 - Connectivity Setup - Software v7.x (BT’08), v6.x, v5.x and v4.x 3-9-7 Set the Scanner’s Network Info rmation - S/W v4.0/v4.1/v5.0/v5.1/v6.0 In the IP settings area of the screen, enter the: 1.) IP Address for scanner. (Default IP Ad dress setting from factory: 10.0.0.3). 2.) Subnet Mask for scanner. (Default Subnet Mask setting from factory: 255.255.255.0). 3.) IP address for Default Gateway. (Default Gate way setting from factory IP address: 0.0.0.0). 4.) Select Save Settings to save any changes you have entered. 5.) In addition, AE Title for the scanner must be entered in the DICOM server’s setup. NOTE: The use of DHCP is not supported by the Servic e Platform, so if DHCP is enabled, the Common Service Platform must be disabled. . Figure 3-42 TCP/IP Set-up for Vivid 7 IP ADDRESS SUBNET MASK DEFAULT GATEWAY AE TITLE SAVE SETTINGS
GE HEALTHCARE DIRECTION FC091194, REVISION 11 VIVID 7 SERVICE MANUAL Chapter 3 - System Setup 3 - 51 3-9-8 Advanced Settings NOTE: New for software V4.0 (BT’04). Advanced Settings give you access to the Network and Dial-up Connections screen where you can set up special network connections and ad just settings for network connectivity. On Vivid 7, Advanced Settings is used to enable/disable DHCP. . Figure 3-43 Advanced Settings ADVANCED SETTINGS TO BE USED FOR ENABLING/DISABLING DHCP.
GE HEALTHCARE DIRECTION FC091194, REVISION 11 VIVID 7 SERVICE MANUAL 3 - 52 Section 3-9 - Connectivity Setup - Software v7.x (BT’08), v6.x, v5.x and v4.x 3-9-9 DHCP Configuration 3-9-9-1 Pre-Requisite • Software version v4.0 or higher. NOTE: The remote connectivity fo r the Global Service Platform will not function if DHCP is active. 3-9-9-2 Turn DHCP ON Follow the instructions below to configure the Vivid 7 to use DHCP . 1.) When in the TCP/IP screen, select ADVANCED SETTINGS to display the Network and Dial-up Connections screen, see Figure 3-45 Network Connections on page 3-53 . Figure 3-44 Advanced Settings ADVANCED SETTINGS
GE HEALTHCARE DIRECTION FC091194, REVISION 11 VIVID 7 SERVICE MANUAL Chapter 3 - System Setup 3 - 53 3-9-9-2 Turn DHCP ON (cont’d) 2.) Select Local Area Connection 3.) Select Properties to display the Local Area Connection Properties 4.) Scroll down to Internet Protocol (TCP/IP) and select it. Figure 3-45 Network Connections Figure 3-46 Local Area Connection Properties
GE HEALTHCARE DIRECTION FC091194, REVISION 11 VIVID 7 SERVICE MANUAL 3 - 54 Section 3-9 - Connectivity Setup - Software v7.x (BT’08), v6.x, v5.x and v4.x 3-9-9-2 Turn DHCP ON (cont’d) 5.) Select Properties 6.) Select Obtain an IP address automaticallyFigure 3-47 Local Area Connection Status
GE HEALTHCARE DIRECTION FC091194, REVISION 11 VIVID 7 SERVICE MANUAL Chapter 3 - System Setup 3 - 55 3-9-10 Set the Remote Arch ive’s Network Information To be able to connect to a remote archive, on a remote computer or server, you must configure Vivid 7 to communicate with it. In the Remote Archive Setup area of the Tcpip screen, see example in Figure 3-48, enter the; 1.) Remote Archive IP address. (Default IP Address from factory: 10.0.0.4). 2.) Remote Archive Name. (Default Remote Ar chive Name from factory: ECHOPAC7-000001). . 3-9-11 Save the New Settings 1.) Select SAVE SETTINGS to save the new settings. . A Warning is displayed on the screen, see illustration below. 2.) The new settings are saved to a common settings file. After a restart, the settings are also included in other screens. 3.) Restart Vivid 7 to activate the changes. Figure 3-48 TCP/IP Set-up for Vivid 7 Figure 3-49 Save New TCP/IP settings Figure 3-50 Warning IP ADDRESS FOR THE REMOTE ARCHIVECOMPUTER NAME FOR THE REMOTE ARCHIVE SAVE SETTINGS
GE HEALTHCARE DIRECTION FC091194, REVISION 11 VIVID 7 SERVICE MANUAL 3 - 56 Section 3-9 - Connectivity Setup - Software v7.x (BT’08), v6.x, v5.x and v4.x 3-9-12 Remote Path Remote Path is used for Save As, Export from Q-A nalysis, and for exporting error logs with the command. Follow this procedure to Configure Vivid 7 to use the Remote Path. 1.) Press Config (F2 ) and log on as ADM, see 4-2-4 Log On to the System as ‘ADM’ on page 4-12 . 2.) If not already selected, select Connectivity from the bottom row of “buttons” on the screen. 3.) Select the Tools tab. 4.) Enter the Remote Path. Example: \\3.187. 187.30\EXPORT\ 5.) Use the Check button to verify the connection. Figure 3-51 Tools screen REMOTE PATH CONFIGURABLE REMOTE PATH USER