Xerox Workcentre 24 Pcl 6 Manual

							4–37
USER GUIDE (MACHINE ADMINISTRATOR)
Color Balance - Yellow,
Magenta, Cyan, BlackThis sets up the default for each density level, Low Density, 
Medium Density, and High Density, for Yellow, Magenta, Cyan and 
Black in Color Balance on the Image Quality screen.
The defaults are all 0.
NOTE: The values set here will also be applied to Black and 
Single Color modes.
Original OrientationThis sets up the default for Original Orientation on the Scan 
Options screen. 
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 0, Head to Top.
Image RotationThis sets up the default for Image Rotation on the Scan Options 
screen. On during Auto refers to Auto Paper selection for Paper 
supply or Auto % for Reduce/Enlarge.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 1, On during Auto.
SettingDescription
0Head to Top
1Head to Left
SettingDescription
0Always On
1On during Auto
2Off 
						

							4–38
USER GUIDE (MACHINE ADMINISTRATOR)
Rotation DirectionSet the default for Rotation Direction when Always On or On 
during Auto is selected in Image Rotation on the Scan Options 
screen.  
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 1, Portrait Original - Left Edge.
NOTE:When the machine is equipped with a Finisher, the default 
will be 0, Auto.
SettingDescription
0Auto (can be selected only when the 
machine is equipped with Finisher)
1Portrait Original - Left Edge
2Portrait Original - Right Edge 
						

							4–39
USER GUIDE (MACHINE ADMINISTRATOR)
Copy Control
This is the setting for Copy Control.
The following items can be set in Copy Control.
Auto Paper OffSet which tray will be selected when Auto % or Independent X-Y 
Auto is selected in Reduce/Enlarge when Auto is selected in 
Paper Supply, on the Basic Copying screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 1, Select Tray 1.
Memory Full ProcedureSet the processing method when the hard disk runs out of memory 
during a job. 
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 0, Disable.
Maximum Stored PagesThis determines the maximum number of stored pages when 
copying documents.  It can be set from 1 to 999 pages.  
Enter the number of the pages using the numeric keypad on the 
Control Panel. The default is 999.
SettingDescription
1Select Tray 1
2Select Tray 2
3Select Tray 3
4Select Tray 4
SettingDescription
0Disable (Discard stored 
documents)
1Enables stored data 
						

							4–40
USER GUIDE (MACHINE ADMINISTRATOR)
Original Size Defaults
This sets up the original sizes that will be displayed when the 
Original Size is displayed from the Scan Options tab.
An original size can be assigned to Original Size Buttons 1 ~ 11. 
Setting frequently used non-standard size in advance prevents 
you from having to input the size each time. When you set up non-
standard sizes, the range for X direction is 15 ~ 432 mm and for Y 
direction is 15 ~ 297 mm.
Original Size Button 1 ~ 11The sizes that can be selected for Original Size Buttons are as 
follows. Select a button and set the size.
The defaults are as follows. The order is from Original Size Button 
1 (Left Upper): A3, A4 SEF, A4 LEF, A5 SEF, A5 LEF, B4, B5 SEF, 
B5 LEF, 11x17 in., 8.5x11 in. SEF, 8.5x11 in. LEF.
SettingDescription
A/B Series SizeA3, A4 SEF, A4 LEF, A5 SEF, A5 LEF, A6 SEF, A6 
LEF, B4, B5 SEF, B5 LEF, B6 SEF, B6 LEF
Inch Size11x17 in., 11x15 in., 8.5x14 in., 8.5x13 in., 8.5x11 
in. SEF, 8.5x11 in. LEF, 5.5x8.5 in. SEF, 5.5x8.5 
in. LEF
Others5x7 in., 3.5x5 in., 8K, 16K SEF, 16K LEF
Va r i a b l eSetting ranges are: 15 ~ 432 mm for X direction, 
15 ~ 297 mm for Y direction in increments of 1 mm 
						

							4–41
USER GUIDE (MACHINE ADMINISTRATOR)
Setting Reduce/Enlarge Presets
This sets up the magnifications that will be displayed in Preset%, 
in Reduce/Enlarge on the Basic Copying screen. 18 different 
magnifications can be assigned to R/E Preset 1 ~ 7.
R/E Preset 1 ~ 7Assign magnifications to R/E Preset 1 ~ 7.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default for R/E Preset 1 is 25.0%.
SettingDescription
125.0%
235.3%
350.0%
457.7%
561.2%
664.7%
770.0%
881.6%
986.6%
10115.4%
11122.5%
12129.4%
13141.4%
14163.2%
15173.2%
16200.0%
17282.8%
18400.0% 
						

							4–42
USER GUIDE (MACHINE ADMINISTRATOR)
Setting Custom Colors
This sets up the user registered colors used in Single Color and 
Dual Colors on the Output Color screen.
Custom Colors 1 ~ 6Assign user registered colors, Yellow (0~100%), Magenta 
(0~100%), Cyan (0~100%), to Custom Color Buttons 1 ~ 6. The 
default is 0.
NOTE: Adjust the registered color so that the sum of Yellow, 
Magenta and Cyan is 240% or less.
Network Settings
Network Settings consists of Port Setting, which determines the 
type of interface of the main unit that is connected to clients, and 
Protocol Setting, which determines the necessary condition for the 
communication.
For more information on setting the Network Settings, refer to the 
System Administrator’s Guide. 
						

							4–43
USER GUIDE (MACHINE ADMINISTRATOR)
Print Mode Settings
Memory volume for each interface, and printer-related settings 
can be set. Print Mode Settings consists of the following 
components.
Allocate MemorySet the size of the reception buffer, where data sent from the client 
is temporarily stored, for each interface.
OthersSet printing area, substitute tray, banner sheet, and banner sheet 
tray.
For more information on printer features, refer to the User Guide 
(Print). 
						

							4–44
USER GUIDE (MACHINE ADMINISTRATOR)
Allocate Memory
Allocate Memory determines memory volume for the reception 
buffer, where the data transmitted from clients is stored, for each 
interface.
For LPD, SMB and IPP you can set whether or not to spool to 
memory, and where to spool. The assigned memory size when 
spooling to memory can also be configured (LPD and SMB only).  
The size of the reception buffer can be changed according to 
machines conditions and your requirements.  If the reception 
buffer is increased, clients using each interface may be released 
quicker.  The maximum value you can set changes according to 
the amount of available memory.
NOTE: When the memory size is changed, the memory will be 
reset, and the data stored in each memory area will be erased.
NOTE: If the set values exceed the size of the installed memory, 
the system automatically adjusts the memory allocation when the 
power is turned on.
NOTE: When a port is set to Disabled, corresponding items will 
not be displayed.
The following items can be configured in Memory Settings.
PCLe MemorySet the memory size for PCLe. 
The memory size can be set between 2.50 ~ 32.00 MB, in 
increments of 0.25 MB.
PostScript MemorySet the amount of memory used by PostScript.  This item will be 
displayed only when a PostScript software kit is installed.
The memory size can be set between 8.00 ~ 32.00 MB, in 
increments of 0.25 MB. The maximum value depends on the 
amount of available memory. The default is 16.00 MB.
HP-GL/2 Auto Layout
MemorySet the memory size for HP-GL/2.
This item only appears when the machine is equipped with PS-
ROM. The size can be set between 64 KB ~ 5120 KB, in 
increments of 32 KB. The maximum value depends on the amount 
of available memory. The default is 64 KB.
Receiving Buffer-ParallelSet the receive buffer on the parallel interface.
The memory size can be set between 64 ~ 1024 KB, in increments 
of 32 KB. The default is 64 KB. 
						

							4–45
USER GUIDE (MACHINE ADMINISTRATOR)
Receiving Buffer-LPD
SpoolChoose from the following options:
•Off - Spooling is not performed. 
While the machine is processing or printing LPD data from a 
client, it cannot receive other data from other clients through 
the same interface.  The LPD reception buffer can be set 
between 64 ~ 1024 KB, in increments of 32 KB. The default is 
256 KB.
•Memory - Spooling is performed.  
Memory is used as the reception buffer for the spooling 
process.  The size of the reception buffer for the spooling 
process can be set between 512 KB ~ 32.00 MB, in 
increments of 0.25 MB. The default is 1.00 MB.
NOTE:Printing data bigger than the memory size set here cannot 
be received.  If this happens, select Hard Disk Spooling or 
Spooling Off.
•Hard Disk - Spooling is performed.  
Hard drive is used as the reception buffer for the spooling 
process. 
The default is Off.
Receiving Buffer-NetWareSet the reception buffer for NetWare.
The memory size can be set between 64 ~ 1024 KB, in increments 
of 32 KB. The default is 256 KB. 
						

							4–46
USER GUIDE (MACHINE ADMINISTRATOR)
Receiving Buffer-SMB
SpoolChoose from the following options:
•Off - Spooling is not performed.  
While the machine is processing or printing SMB data from a 
client, it cannot receive other data from other clients through 
the same interface.  The SMB reception buffer can be set for 
64 ~ 1024 KB, in increments of 32 KB. The default is 256 KB.
•Memory - Spooling is performed.  
Memory is used as the reception buffer for the spooling 
process.  The size of the reception buffer can be set between 
512 KB ~ 32.00 MB, in increments of 0.25 MB. The default is 
1.00 MB.
NOTE:Printing data bigger than the set memory size cannot be 
received.  If this happens, select Hard Disk Spooling or Spooling 
Off.
•Hard Disk - Spooling is performed.  
Hard drive is used as the reception buffer for the spooling 
process.
The default is Off.
Receiving Buffer-IPP SpoolChoose from the following options:
•Off - Spooling is not performed.  
While the machine is processing or printing IPP data from a 
client, it cannot receive other data from other clients through 
the same interface.  The IPP reception buffer can be set 
between 64 ~ 1024 KB, in increments of 32 KB. The default is 
256 KB.
•Hard Disk - Spooling is performed.  
Hard drive is used as the reception buffer for the spooling 
process.
The default is Off.
Receiving Buffer-EtherTalkSet the reception buffer for EtherTalk.
The size can be set between 64 ~ 1024 KB, in increments of 32 
KB. The default is 256 KB.
Receiving Buffer - Port9100Set the reception buffer for Port9100. 
The size can be set between 64 ~ 1024 KB, in increments of 32 
KB. The default is 256 KB.