Xerox Workcentre 24 Pcl 6 Manual

							4–27
USER GUIDE (MACHINE ADMINISTRATOR)
NOTE: If No Default is selected, an Output Color must be selected 
for copy jobs, or the machine will not start copying. 
NOTE: If Black is selected on the Basic Copying screen, the copy 
output will have the same image quality as Halftone, selected in 
Text&Photo.
NOTE: When Dual Colors or Single Color is selected on the Basic 
Copying screen, the Original Type cannot be set.
Single ColorSet the default for Single Color on the Basic Copying screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 1, Red.
Dual Color - Color ImageSets the default for Color Image in Dual Color on the Basic 
Copying screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 1, Red.
Dual Color - B/W ImageSet the default for a B/W Image in Dual Color on the Basic 
Copying screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 0, Black.
SettingDescription
0Black (can be only be set when Dual Color is 
selected)
1Red
2Green
3Blue
4Ye l l o w  ( Y )
5Magenta (M)
6Cyan (C)
7Specified Color set to Custom Color 1
8Specified Color set to Custom Color 2
9Specified Color set to Custom Color 3
10Specified Color set to Custom Color 4
11Specified Color set to Custom Color 5
12Specified Color set to Custom Color 6 
						

							4–28
USER GUIDE (MACHINE ADMINISTRATOR)
Reduce/EnlargeSets the default for Reduce/Enlarge on the Basic Copying screen.
Select one of nine buttons. Seven buttons are registered as preset 
ratio buttons, 100%, and Auto %.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 0, 100%.
NOTE: If the default for Paper Supply is set to Auto, Auto% cannot 
be selected for Reduce/Enlarge.
Paper SupplyThis sets the default for Paper Supply on the Basic Copying 
screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 0, Auto.
If the default for Reduce/Enlarge is set to Auto%, Auto cannot be 
selected.
SettingDescription
0100%
1Ratio set to R/E Preset 1
2Ratio set to R/E Preset 2
3Ratio set to R/E Preset 3
4Ratio set to R/E Preset 4
5Ratio set to R/E Preset 5
6Ratio set to R/E Preset 6
7Ratio set to R/E Preset 7
8Auto%
SettingDescription
0Auto
1Tray 1
2Tray 2
3Tray 3
4Tray 4
5Tray 5 (Bypass) 
						

							4–29
USER GUIDE (MACHINE ADMINISTRATOR)
2 SidedThis sets up the default for 2 Sided on the Basic Copying and 
Added Features screens.  
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 0, 1 to 1.
OutputThis sets up the default for Output on the Added Features screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 0, Auto.
Output DestinationThis sets up the Output Tray for copy and print jobs.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 0, Center Output Tray.
NOTE: The Optional Finisher must be installed to use the Finisher 
Tr a y.
SettingDescription
01 to 1 Sided
11 to 2 Sided
22 to 1 Sided
32 to 2 Sided
SettingDescription
0Auto
1Collated
2Uncollated
SettingDescription
0Center Output Tray
2Finisher Tray 
						

							4–30
USER GUIDE (MACHINE ADMINISTRATOR)
Margin Shift - Side 1This sets up the default for Side 1 in Margin Shift on the Added 
Features screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 0, No Shift.
SettingDescription
0No Shift
1Auto Center
2Corner Shift (Top Right)
3Corner Shift (Bottom Right)
4Corner Shift (Top Left)
5Corner Shift (Bottom Left)
6Corner Shift (Top Center)
7Corner Shift (Bottom Center)
8Corner Shift (Left Center)
9Corner Shift (Right Center) 
						

							4–31
USER GUIDE (MACHINE ADMINISTRATOR)
Margin Shift - Side 2This sets up the default for Side 2 in Margin Shift on the Added 
Features screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 10, Symmetrical with Side 1.
Border Erase - Top &
BottomThis sets up the default for the top and bottom Border Erase.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 5mm.
SettingDescription
0No Shift
1Auto Center
2Corner Shift (Top Right)
3Corner Shift (Bottom Right)
4Corner Shift (Top Left)
5Corner Shift (Bottom Left)
6Corner Shift (Top Center)
7Corner Shift (Bottom Center)
8Corner Shift (Left Center)
9Corner Shift (Right Center)
10Symmetrical with Side 1
SettingDescription
0None
1 ~ 50Set the border erase 
amount in increments 
of 1mm 
						

							4–32
USER GUIDE (MACHINE ADMINISTRATOR)
Border Erase - Left & RightThis sets up the default for the left and right Border Erase.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 5mm.
Center EraseThis sets up the default for Center Erase. It is distributed along the 
center of the original image.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 0 mm.
SettingDescription
0None
1 ~ 50Set the border erase 
amount in increments 
of 1mm
SettingDescription
0None
1 ~ 50Set the center erase 
amount in increments 
of 1mm 
						

							4–33
USER GUIDE (MACHINE ADMINISTRATOR)
Original Type (Auto/Full
Color)This sets up the default for Original Type on the Image Quality 
screen, when Auto or Full Color is selected as the color mode on 
the Basic Copying screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 1, Text & Photo (Halftone).
Original Type (Black)This sets up the default for Original Type on the Image Quality 
screen, when Black is selected as the Output Color on the Basic 
Copying screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 1, Text & Photo (Halftone).
NOTE: When Dual Color or Single Color is selected as the Output 
Color on the Basic Copying screen, the Original Type setting is 
ignored.
SettingDescription
0Te x t
1Text & Photo (Halftone)
2Text & Photo (Photograph)
3Text & Photo (Color Copies)
4Photo (Halftone)
5Photo (Photograph)
6Photo (Color Copies)
7Color Originals (Map)
8Color Originals (Highlighted 
Originals)
9Color Originals (Inkjet Originals) 
						

							4–34
USER GUIDE (MACHINE ADMINISTRATOR)
Auto ExposureThis sets up the default for Auto Exposure, when Text&Photo, 
Text, or Color Originals is selected in Original Type on the Image 
Quality screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 1, Auto Exposure On.
Lighter/DarkerThis sets up the default for Lighter/Darker in Light/Dark/Contrast 
on the Image Quality screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 3, Normal.
SettingDescription
0Auto Exposure Off
1Auto Exposure On
SettingDescription
0Light (+3)
1Light (+2)
2Light (+1)
3Normal
4Darker (-1)
5Darker (-2)
6Darker (-3) 
						

							4–35
USER GUIDE (MACHINE ADMINISTRATOR)
ContrastThis sets up the default for Contrast in Light/Dark/Contrast on the 
Image Quality screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 2, Normal.
SharpnessThis sets up the default for Sharpness in Sharpness/Saturation on 
the Image Quality screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 2, Normal.
SettingDescription
0Higher
1High
2Normal
3Low
4Lower
SettingDescription
0Sharper
1Sharp
2Normal
3Soft
4Softer 
						

							4–36
USER GUIDE (MACHINE ADMINISTRATOR)
Color SaturationThis sets up the default for Color Saturation in Sharpness/
Saturation on the Image Quality screen.
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 2, Normal.
Color ShiftThis sets up the default for Color Shift on the Image Quality 
screen.  
Enter the setting on the Numeric Keypad using the numbers listed 
in the following table. The default is 2, Normal.
SettingDescription
0Higher
1High
2Normal
3Low
4Lower
SettingDescription
0Coolest
1Cool
2Normal
3Warm
4Warmest