Home > GTE > Communications System > GTE Omni Si Database Technical Practices Manual

GTE Omni Si Database Technical Practices Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual GTE Omni Si Database Technical Practices Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 950
    Add page 721 to Favourites
    image text
    Enable zoom 
    							5210TL-130200-10012.If C register is 00, 02, 03, 05, 06, or 07, complete the following
steps:
-Force CIPNCIPIDVCIP 00s - FORCE CIP CA X YY OS.
x=PEC 
#3, Always 0 orFORCE VPLC (PEC GRP SLOT)
W=CARD 30 -15
-Remove and replace CIPNCIPIDVCIP, FB -17235
A/17236-A in identified slot (check strapping).
-Force CIPNCIPIDVCIPNP20 INS - FORCE CIP CA X YY IS.
x=
PEC#, Always 0 orFORCE VPLC (PEC GRP SLOT)
W=CARD #O -15
3.If PCB replaced is a VCIP/DVCIP, FB-17235-A/17236-A, force
download the PCB as follows:
-Identify data links associated with relative card number of the
.
VCIP/DVCIP (i.e., VCIP #O/DVCIP #0 = Data Links O-7, VCIP
#DVCIP #l= Data Links 8-15, etc.)
-Identify any SID associated with any previously defined data
link by reading Table 
T7054-0.
-Force download of this VCIPIDVCIP using the previously
defined 
SiD:Force download X YYY IN.
x=PEC#, Always 0
YYY=SID 
#O-255
4.If fault recurs, reinstall original 
CIPNCIPIDVCIPnIP20 card and
download.
5.Identify MPB85, FB-17215-A associated with identified
CIPNCIPIDVCIP card:
MPB85PCMUS GROUP
Y/O5Groups A & B
X/o4Groups C & D
6.Power down system - turnoff main circuit breaker at rear of
OMNI SI cabinet.
7.Remove and replace MPB85, FB-17215-A previously
identified.
8.Power up system.
9.Monitor PSUPY card in P/O1 for ASW LED to light.
10.If C register value is 04, complete the following steps:
-If a CIPIVCIPIDVCIPNP20 card is supposed to be in an
unequipped slot, install a CIPNCIPIDVCIP card.
-.If a CIP/VCIP/DVCIP card is correctly installed in the PCMUS,
follow procedures for C register value 00 listed above.
8187M-145
    Add page 722 to Favourites
    image text
    Enable zoom 
    							TL130200-1001
FAULT CODE 321FAULT CODE 
- 32
II1FORCE 
CIP/VCIP/DVCIP
b CARD OS: FORCE CIP CA X
w OS.
$rFORCE CIPNCIPIDVCIP
CARD.
CIP, FB-17225VCIP, FB-17235
DVCIP, FB-17236
4
IFORCE CIPNCIPIDVCIP
CARD INS:FORCE CIP CA X YY IS.
x-YES
IDENTIFY DATA LINKS
ASSOCIATED WITH 
VCIP/DVCIP RELATIVE CARD NO.
NO
NO
NOREINSTALL ORIGINAL
VCIP, 
FB-I 7235 OR
DVCIP, FB-17236IDENTIFY MPB85,
rFB-17215ASSOCIATED WITH
PCMUS HOUSING
CIPNCIPIDVCIP
CARD
+POWER DOWN
SYSTEM
+R&R MPB85, 
FB-17215 PREVIOUSLY 
-
IDENTIFIED
-AENDM-146
ah375210
    Add page 723 to Favourites
    image text
    Enable zoom 
    							TL-130200-1001Fault Code 33Description:
CIPNCIPIDVCIPThis fault indicates a failure in the Integrated/Digital
Port FailureFeaturephone cabling or CIPNCIPIDVCIP card.
5210
Register Data as System Prints:CECO CECO Fault 33 B C 
D E H L
00 00 00
00= Data Link Error
01= CIP Port Protocol Error
02= Port Sync Error
03= Port Enable Error
04 = CIP Other Port Errors
05= Test Failure
06 = Download Failure
07 = Port Recovery Errors
Fault Resolution Steps:
1.Identify and locate Featurephone associated with fault report
(customer complaint) or determine DN by deciphering port
number
2.Ensure that Featurephone is powered up.
3.Run self-test - TEST PHONE DN XXXX or TEST DN
XXXX. If test fails, remove and replace Featurephone.
4.If Featurephone passes self-test, complete the following
steps:
- At system maintenance terminal call up Recent Change
menu 117 to show the PCMUS associated with the
CIP/VCIP/DVCIP. When PCMUS is defined, identify
CIPNCIPIDVCIP relative card number location by
performing a general read of 17053-O address 
(B2Fthrough 
OB3E) as shown below:
GR D2 
OB2F OB3E.
OB2F = Relative Cl Card No. 0
OB30 = Relative Cl Card No. 1
OB31= Relative Cl Card No. 2
OB32 = Relative Cl Card No. 3
OB33 = Relative Cl Card No. 4
OB34 = Relative Cl Card No. 5
0835 = Relative Cl Card No. 6
OB36 =Relative Cl Card No. 7
8167M-l 47
    Add page 724 to Favourites
    image text
    Enable zoom 
    							TL-130200-1001
0637 =
Relative Cl Card No. 8
OB38 =
Relative Cl Card No. 9
0839 =
Relative Cl Card No. 10
063A =
Relative Cl Card No. 11
OB3B =
Relative Cl Card No. 12
OB3C =
Relative Cl Card No. 13
OB3D =Relative Cl Card No. 14
OB3E =Relative Cl Card No. 15
- Using the relative Cl card number, force the
CIP/VCIP/DVCIP 00s.Force 
CIPAJCIPIDVCIP 00s - FORCE CIP CA X YY OS.
x=PEC#, Always 0
YY=CARD #O-l 5
- Remove and replace CIPNCIPIDVCIP, FB-17235
A/l 7236-A in identified slot (check strapping).
Force CIPNCIPIDVCIP INS 
- FORCE CIP CA X YY IS.
x=
PEC#, Always 0
YY=
CARD #O-l 5
- If PCB replaced was a VCIPIDVCIP, F&17235-
A/17236-A, force download PCB as follows:
- Identify data links associated with relative card number of
the 
VCIPIDVCIP (i.e., VCIP/DVCIP #0 = Data Links O-7,
VCIP/DVCIP #l= Data Links 8-15,etc.).
- Identify any SID associated with any previously defined
data link by reading Table T-7054.
- Force download of this VCIP/DVCIP using the previously
defined SID:
Force download X YYY IN.
X = 
PEC#, Always 0
YYY=SID #O-255
- If fault recurs, reinstall original CIPIVCIPIDVCIP card.
- Identify MPB85, FB-17215-A, associated with PCM
group housing identified 
CIP/VCIP/DVCIP card.
MPB85PCMUS GROUP
Y/O5Group A & B
x/o4Group C 
& D
5.Power down system 
- turn off main circuit breaker at rear of
OMNI Sl cabinet.
6.Remove and replace MPE385, FB-17215-A, previously
identified.
7.Power up system.
8.Monitor PSUPY in P/O1 for ASW LED to light.
M-148
81875210
    Add page 725 to Favourites
    image text
    Enable zoom 
    							RUN SELF-TEST ON
FEATUREPHONE TEST
PHONE, DN XXXX, OR
TEST DN XXXX.TL-130200-1001
IDENTIFY ANY SID
ASSOCIATED WITHPREVIOUSLY DEFINEDDATA LINKS
RELATIVE CARD NO.
4ASSOCIATED WITH
FORCE DOWNLOADON 
VCIP/DVCIP:
FORCE DOWNLOADX YYY IN.
fREINSTALL ORIGINAL
VCIP, FB-17235, OR
DVCIP, FB-17236
IREINSTALL ORIGINAL
CIP, FB-17225 CARDIDENTIFY MPB85,
FB-17215ASSOCIATED WITH
PCMUS HOUSING
ClPNClPlDVClP CARD PCMUS ASSOCIATION
CIPNCIPIDVCIP PCB
VCIP/DVCIP RELATIVE
FEATUREPHONE
‘ZIP, FB-17225
VCIP, FB-17235
DVCIP, FB-172365210
8l87M-149
    Add page 726 to Favourites
    image text
    Enable zoom 
    							TL-130200-1001Fault Code 36Description:
Change MDR SystemThis fault indicates that receiving a CRIB (Call Record
Clock FailureInformation Buffer) from the idle crib list failedThe indication isthat MDR failed to change its system clock after a request from a
user. If this happens, there were too many calls in progress to
handle the request.
M-l 50
Register Data as System Prints:CECO CECO Fault 36 B C D E H L
,xx,,xx,,xx,\xx/?
    Add page 727 to Favourites
    image text
    Enable zoom 
    							TL-130200-1001Fault’Code 37Description:
System Warm StartFault Code 37 is generated every time a warm or cold start
occurs in the system. Register B in Fault Code 37 contains the
total count of warm starts which have occurred since the last
cold start. If Register B= 0, then a cold start has occurred.
Register C contains the threshold count for this fault. If register C
contains any value other than 0, the system has attempted a
warm start in 4 minutes or less since the last warm start. If
register C is 5, the system will attempt a cold start.
hedster Data as Svstem Prints:
-CECO CECO
    Add page 728 to Favourites
    image text
    Enable zoom 
    							TL-130200-1001Fault Code 41Description:
FMS Disk ErrorThis fault indicates genera
M-l 52.I disk I/O errors.
Register Data as System Prints:CECO CECO Fault 41 B C D E H L
rRequest which failed
OE =Writing Out Data Base
14 =Writing Out 
HC/M
1D =Downloading F/P File
1F= Closing F/P File
Error CodeDCBDRB Start
FF 
=.SequenceAddress
TimeoutIndex(Low Byte)
(TCSIX)
Fault Resolution Steps:
1.Repeat the task that was being performed when fault
occurred. If fault recurs, continue.
2.If the C register value is FF, this might indicate a hardware
problem. Complete the following steps:
- Power down - turn off main circuit breaker at rear of
OMNI SI cabinet.
- Remove and replace FMSD, FB-17220-BOA, in Y/O7(check strapping).
- Power up system.
- Monitor PSUPY card in P/O1 for ASW LED to light.
- If fault recurs, remove and replace the floppy disk drive.
- If fault still recurs after performing above procedures, this
indicates an internal data base or software problem and
the technician should call for assistance.
71875210
    Add page 729 to Favourites
    image text
    Enable zoom 
    							TL-130200-1001. c-w-. VVIb -r. 
.REPEATTASK
JUST PERFORMED
+.
NO
* YESC=FF
FB-17220 IN 
Y/O7PSUPY FOR
NO
* YES
R&R FLOPPY
DISK DRIVE
52107187M-153
    Add page 730 to Favourites
    image text
    Enable zoom 
    							TL-130200-1001Fault Code 42Description:
Time Slot LockupFault Code 42 is generated when a time slot lockup is detected.When allocating a time slot, a check should be made to see if the
hardware ID is already in channel memory. If it is, then a time
slot is locked up. The old time slot is released before allocating
the new time slot.
Register Data as System Prints:CECO CECO Fault 42 B C D E H L
00 \xx y \xx 00 00
Hardware
IDTime Slot Call Store
NumberNumber
M-l 54
71875210
    All GTE manuals Comments (0)

    Related Manuals for GTE Omni Si Database Technical Practices Manual