GTE Omni Si Database Technical Practices Manual
Have a look at the manual GTE Omni Si Database Technical Practices Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
TL-130400-1001COL.NO. Table 8.1Entry Fields for Record Code LD (Continued) COL.VALID NAMEENTRIESCOMMENTS 49-50Message Detail00-63 = groupAssign the MDR work group number to the Recorder Work numberstation. Group Numbers-- = N/A-The stations are divided into groups .”default = 00according to the information output required. . . .for each group. . -MDR work groups are normally arranged in groups of like users for billing purposes (e.g., all accounting department telephones can be in the same group). -The MDR print-out gives the PDN (Prime Directory Number) of the station. -MDR group 00 is used as the default value and should not be assigned to stations. -If columns 16-19 are marked POTS, PACT, AIFP, DFPA, or DIFP, these columns must not be dashed. -If columns 16-19 are marked APM, SPM, or dashed, these columns must be dashed. 51Remote AccessR = remote accessThis field determines whether or not the andA = authorizationremote access (or remote access requiring Authorizationcode required withan authorization code) feature can be used Coderemote accessfrom this line. - = N/A-If an R is entered in this field, then the line can be used for remote access. -If this field is marked with an A, the line can be used for remote access. However, an authorization code is required. -By giving either of these features to a line, the COS normally assigned to this line can be temporarily overridden (e.g., a roving manager could make a toll call from a toll restricted line).-If columns 16-l 9 are dashed, this column must also be dashed. -If the line type is DA (columns 28-29) this field must be dashed.SVR 5210 8187D-l 51
Table 8.1Entry Fields for Record Code LD (Continued) COL.COL.NO. NAME 52Controlling Data Control _ Processor .-Software ‘”VALID ENTRIES 0 = number -=N/ACOMMENTS This field determines the controlling DCP (Data Control Processor) software number assigned to this Digital Featurephone. -The DCP is otherwise known as the UCB (Universal Control Board) -This field only applies to a Digital Featurephone used with the PD-200 Data Option.-If the PD-200 Data Option is in use, enter 0.-Because one UCB can support up to 240 data ports, only one is needed in the OMNI SI. -The UCB must be defined on Record Code FR.-This field is new to SVR 5210. NOTE: UCB is the card; DCP is the software on the card.
TL-130400-1001Record Code LM: Line Miscellaneous %-.”-..8.2 Record Code LM, Figure 8.2, is an extension of Record Code LD and provides additional data for lines. Any directory number that appears on this record code must appear on Record Code LD as well. Instrument types APM, SPM, PACET, or ---, as well as line types Ll and NW, never have an LM entry. LM is required for Analog Featurephones (instrument type AIFP). LM is used whenever the signal mode is something other than MX. It is also used if a field on LM is needed to complete the description of a line. I I I -II I II I I I I I I I I II I I I I I I I I I I I I II I I I ‘1I I I I I II-T-T-f-T-t-T-T-T-t-T-t-t-t-T-t-T-+-T-T-T-t~I I-,--;-T-I1I1I1I1I1I111I1111112121212121212121:2121313 718191011121314151617181910111213141516171~ 8191011 -+-+-+-u-+-+-+-+-+-+-+-+-+--c-+-+-+-+-+-+. -+-+-+-31I31lj1LI~I I I I I I I I I I I I I I I I I I I I III IIII II I -,-;-,-l-,-,-,-4I 1r-:11313131313131311811131415161718191101-+-+-+-+-+-+-+-Ac-4I I I I I I I II Im--e---_LA_A_A_A_A_A_A_* . * . . . . . * * * . * * . , . . . ------a.-~ Figure 8.2Record Code LM: Line Miscellaneous Data Sheet
TL-130400-1001Yable 8.2 Entry Fields for Record Code LM Assign the line directory number to the equipped line circuits in the system. -Three-digit numbers must be right justified. line service, or-If the instrument type(columns 16-19 ofRecord Code LD) is marked POTS, this field Record Code LD) is marked AIFP or DFPA, this field must be marked DP. requiring a mixture-If this field is marked NO, the SCC (non-MERS) access allowed in COS (Record Code and dialpulse; orNC, columns 66-67) will not work. MX can be used in-If this field is marked NO, the following COS place of DP andfeatures defined by Record Code DD will not TC (MX is used forwork: toll access, meet-me conference, POTS,progressive conference, dictation, paging, Featurephones,maintenance access, modem access, MERS and default.) on-net.-If this field is marked NO, the following COS features defined by Record Code NC will not work: executive override, originating call waiting, camp-on/auto recall, attendant information, dial call pickup, call forwarding variable, speed call, universal night answer. 18Data Link Card0 = PEC number-Enter PEC 0. Location: PECThis is the PEC entry for the FB-17225 card that supports the IFPs.-Data link cards are defined for Agent Instruments on Record Code AD.
COL.NO. 19 20-21 22-23 24-27 28-29TL-130400-1001 Table 8.2Entry Fields for Record Code LM (Continued) COL.NAME Data Link Card -ocation: Group Xtta Link Card -ocation: Card Slot Data Link Card -0cation: Circuit Vumber Zontrollingntegrated =eaturephoneCall Divert ConditionVALID ENTRIES 4-D = grouplumber 30-l 1 = slotlumber J-7 = assigned circuit number 1000-9999 =‘our-digit line directory number :-OOO)-(-999) =:hree-digit line Directory number VD = no divert, ncluding hunt Jroup members 3Y = divert if busy VA = divert if no answer3N = divert if busy )r no answer DA = divert always (used for CO lines and hot lines)COMMENTS Which group (A, B, C, or D) within the PEC is this card? Which card slot within the group is this card? Which circuit on the card is being used? This field determines the primary line directory number for non-prime and CO lines. -If the instrument type (columns 16-19 of Record Code LD) is marked POTS, this field must be dashed. -When defining the PDN (Prime Directory Number), this number will be the same as the directory number. Columns 28-31 are used to define divert conditions. Assign the conditions under which a call will divert. Columns 30-31 define what type of destination the call diverts to. The destination itself is defined on Record Code LD, columns 45-48. -The call divert fields are used to implement the following features: fixed call forwarding, hot line switched direct line service, diversion of one hunt group to another (via last member). -Use Record Code MH to program hunt group member searches and LD to specify the divert destination identification for call diverts. -The divert always condition will allow a call to be forwarded twice only. The third attempt rings busy. -Columns 28-29 define the conditions that cause a call to forward from the called station to another location. -If this value is set at ND, the allowable value of columns 30-31 is --, TO, LN, AT, TR, or PN. -If this value is set at BT, NA, BN, or DA, the allowable value of columns 30-31 is TO, LN, AT, TR, or PN. -If Record Code NC, columns 38-39, is marked OR (for COS originating only), this field should be marked ND.
rTL-130400-1001Table 8.2Entry Fields for Record Code LM (Continued) COMMENTS under which a call will divert. Columns 30-31 define the type of destination to which the call diverts. The destination itself is defined on Record Code LD, columns 45-48. -If this value is --,the allowable value of the divert destination identifier (Record Code LD, columns 45-48) is ---- . -If this value isset atLN,theallowable value of the divert destination identifier (Record Code LD, columns 45-48) is 0000-9999 (station number). -If this value is set at AT, the allowable value of the divert destination identifier (Record Code LD, columns 45-48) is 0064, 0128, or -If this value is set at TR, the allowable value of the divert destination identifier (Record Code LD, columns 45-48) is 0000-0063. -If this value is set at PN, the allowable value of the divert destination identifier (Record Code LD, columns 45-48) is 0000-9999 (hunt group pilot number). -If this value is set at SC, the allowable value .of the divert destination identifier (Record Code LD, columns 45-48) is 0001-0008 of the divert destinati Code LD, columns 4
TL-130400-1001COL.NO. Table 8.2Entry Fields for Record Code LM (Continued) COL.VALID NAMEENTRIESCOMMENTS 32-33Ward Number00-31 =This hospital feature is used to provide quiet ward numberhours to patient room telephones. -- = N/A-The system supports a maximum of 32 ward x-numbers..”-The field determines which ward number is assigned to a station. .-Ward numbers are created on Record Code WT, columns 21-52. -If an entry is made in this field, then at least one entry on Record Code WT, columns 21- 52, must be marked A. 34-35Reserved-- = only allowedThis field is reserved for future use and is only entryto be dashed. 36MultilineY = MultilineIf the instrument type is an IFP, this field FeaturephoneFeaturephonedetermines if it is used as a multiline -= N/Atelephone. -It is recommended to configure all IFPs as multiline (whether or not they are) because a multiline IFP has a hold button and a single-line IFP does not.SVR 5210
Record Code LA:8.3 Record Code LA, Figure 8.3, defines all the directory Line Appearancesnumbers that appear as either a line or a DSS (Direct Station Select) on the multiline Integrated Featurephones. ‘---------T-------T-------T---T------___-___________--_---------------------_I I I I I I , ’ ’ I1 ITI’ ‘RII ‘AI1 INI’ ,SlICI I 10;’ ,Dl1,EII’ ’ IIIII I’ ’ IIIII I’ ’ III I1f’ ’ III I’ ’ IIII II’ ’ III II’ ’ IIIII I’ 1 IIIII I’ ’ IIIII I’ ’ IIII1’ ’I I1 I1 I1 11 II II II 11 II 11 1212121212121212121213131313131313131313l4l4l4lf7%9,0,1 ,2,3,4,6,6,7,81910,1 ,2,3,41516,7,8,9,011 12,3,415161718191011 I21 IO1~-+-+-+-u-+-+-+-~-:-+-+-:-+-+-+-+-+-+-+-+-+-+-+-:-:-:-:-:-:-:-:-:-:-:-:k-41016l7l~l~l I l lI 1I I I I I I,, I I1I IL-L-L-~-L--~-~-~--L-~-~-~-~-~-~-~-*-*-*-*-*--L-~-~--C-~-~-~-~-~-~-~-~-~-~ Figure 8.3Record Code LA: Line Appearances Data SheetSVR 5210
TL-130400-1001Table 8.3Entry Fields for Record Code LA COL.COL.VALID NO.NAME ENTRIESCOMMENTS 12-15Line Number of 0000-9999This field determines the multiline IFP line the Integrated directory number on which the lines or DSSsFeaturephone ~~0-999 =appear. Right justify three-digit numbers..”number-Any line appearing in this field must be A three-digitmarked as a multiline IFP on Record Code LM number must have(Y in column 36). a blank before it.-If a line appears on Record Code LA, the . CPG defaults to multiline. 16-19Line Number of 0000-9999This field determines the line number of the Appearance orappearance. 000-999 =Right justify three-digit numbers. number 20-21Appearance We LA = lineappearance (Featurephone only 1DS = DSSappearanceThis field determines whether or not the appearance is a line or DSS. -Controlling numbers and logical lines are not to appear on this record code. -A POTS telephone can only appear as a DS (DSS) because a POTS line cannot appear on another phone. -An LA (line appearance) on this record code can only be an Analog or Digital Featurephone. -If a line is defined as a CO line on Record Code LD, it cannot appear as a DS (DSS) on this record code. -A line directory number listed as an appearance must be defined on Record Code LD, columns 12-l 5. -The system supports a maximum of eight appearances (line or DSS) of the same line. -A single-line Featurephone (see Record Code LM, column 36) cannot be a line appearance. SVR 5210
TL-130400-1001Record Code LI:8.3 Record Code LI, is not input by the customer. It is Line Identitiesgenerated by the reverse CPG to preserve the assignments of internal system identities for re-engineering or documentation purposes. s-.”. . . .SVR 5210