GTE Omni Si Database Technical Practices Manual
Have a look at the manual GTE Omni Si Database Technical Practices Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
-.--TL-130400-1001 NETWORKING 12.0 This section describes the record codes required to define the various networking features. The following record codes are required: . .SVR 5210l Record Code NT defines the routing for private tandem switching networks. l Record Code TD defines the translation of the digits for a tandem network. 8187D-253
TL-130400-1001D-254 Record Code NT: Private Network12.1 Record Code NT, Figure 12.1, defines the first level call routing for private tandem switching networks. Use one record Translationfor each RNX (or RNX range) with the same routing characteristics in the RNX numbering plan. ‘---------r-----------T---------------____~-----~-----------------1---------- Record Code NT: Private Network12.1 Record Code NT, Figure 12.1, defines the first level call routing for private tandem switching networks. Use one record Translationfor each RNX (or RNX range) with the same routing characteristics in the RNX numbering plan. ‘---------r-----------T---------------____-r------r-----------------1---------- Figure 12.1Record Code NT: Private Network Translation Data Sheet Table 12.1Entry Fields for Record Code NT COMMENTSNote: A conflict exists with the three-digit translated NPA’s warning message. The private network digit analysis is combined with the three-digit translation (Record Code NR) on the same data base table. A problem may occur if the private network digits contain MRN or MER = type MRS = off-networkMERSprocessingon7TGS = trunk group selection and outpulsing of received digits (see columns 21-24) 8187SVR 5210
TL-130400-1001Table 12.1Entry Fields for Record Code NT (Continued) COMMENTSN digits (see columns 21-22) ABC = analysis of the ABC code before routing DGT = analysis of Dl /D2 (digit 1, digit 2) of the last four terminal digits before sending MRN = private network MERS processing on 7 international dialing. given in columns 18-20 is either TGO or TGS. Indicate the trunk group used for outpulsing the digits. Digits Outpulsed -- = N/AThis field isonly usedif the translation type given in columns 18-20 is TGS. -Enter the number of digits outpulsed. 25-27 Private NetworklNPACode 200-999, ONl-ON4or ---This field determines the private network code (ONl-ON4) or the NPA code number (200- 999).200-999 = NPA code as defined on Record Codes MR and TR QNl-ON4= private network code as defined on Record Codes AC and TR -Record Code TR defines the phantom number used for on-network dialing. -This field must be used if columns 18-20 are marked MRN. For all other entries in columns 18-20, this field is dashed. 28-29,SendingOl-31= numberThese fields can be used only if the translation 31-32,Instruction List-- = N/Atype given in columns 18-20 is MER. Assign 34-35,Numberthe sending instruction list number to be used 37-38.for the various time periods. The sending instruction list numbers are defined on Record Code SI, columns 12-13. 30, 33, 38, 39.Route List O-7 = numberNumber -=N/AThese fields can be used only if the translation type given in columns 18-20 is MER. Assign the routing list number to be used for the various time periods. The routing list numbers are defined on Record Code RP, column 12. SVR 52108187D-255
TL-130400-1001Record Code TD: Private Network12.2 Record Code TD, Figure 12.2, defines, in a seven- or Dl/D2ten-digit, format, the translation of the digits for a tandem network. These digits are the Dl/D2 digits of the four terminal digits (Dl, D2, D3, D4). -.. __NOTE: There is a conflict with the three-digit translated NPA warning message. The private network digit analysis was combined with the three-digit translation (Record Code NR) in the same data base table. A possible problem exists if the private network digits contain conflicting codes. D-256 (- ----- -----r----r----------I---------T-----------------------------------------~I II.-T1Ii I II 17 18 I9 10 I1c-+-+-+-+-!2;8;8 ITI 0- - --t I-T-t-T-T-t-T-t-T-t-T-T-t-T-T-T-T-T-T-T-T-T-T-T-T-T-T-T-T-f-T-T-T-i1 I1 I1 I1 I1 I1 I1 I1 1212121212121212121213131313131313131313l4l4l4l21314151617181910111213141516171819101112131415161718191011121 -+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-~I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I-.L-*-A-.L-~-*-*-*-*-~-*-~-*-i-*-~-*-*-~-~-~-~-~-A-.&--L-A.-A-- I IIII I Figure 12.2Record Code TD: Private Network Dl/D2 Data Sheet 8187SW 5210
TL-130400-1001COL.NO.Table 12.2Entry Fields for Record Code TDCOL.VALID NAME ENTRIESCOMMENTS 12-13First Two Digits00-99 = number This field determines the first two digits of Terminal (Dl/D2) of the four terminal digits that require Digits local termination or outpulsing. .”.-..-The first two digits of the terminal digits must be unique across all TD records. -These digits must correspond to a hundreds ,.group engineered on Record Code HD. -If the first two digits are OX, then both OX and X hundreds groups must not be specified on Record Code HD. -If a number is listed here, the system will process both hundreds groups with the first two digits of OX for this application. 14-16TranslationLOCIndicate the type of translation assigned to the TypeMRSroute.TGSLOC = local termination based on the last four TGOdigits orMRS = off-network MERS processing on 7 MRNand 10 digits TGS = trunk group selection and outpulsing of all received digits (see columns 17-18) TGO = trunk group selection and outpulsing of last N digits (see columns 17-20) MRN = on-network MERS processing on 7 and 10 digits (see columns 21-23) 17-18Select Trunk 00-63 = numberThis field is only used if the translation type Group-- = N/Adefined in columns 14-l 6 is TGO or TGS. -Assign the trunk group used for outpulsing the digits. -The selected trunk group must be defined on Record Code Tl.-The trunk application on Record Code Tlfor this trunk group cannot have values of DIC, PAG, or REC. 19-20Number of00-l 5 = numberThis field is only used if the translation type Digits Outplused -- = N/Adefined in columns 14-16 is TGO. -The field determines the number of digits outpulsed. -If a five-digit numbering plan is in effect, the number of outpulsed digits must be indicated here. SVR 5210 8187D-257
I TL-130400-1001Table 12.2Entry Fields for Record Code TD (Continued) COL.VALID NAMEENTRIES I 21-23On-Net/NPA200-999Code ON1 -ON4 = codes-Or.”. .m-s = N/A.COMMENTS This field is only used if the translation type defined in columns 14-16 is MRN. -This field determines the on-network code(ONl-ON4) or the NPA code number (200- 999).Note: Only four unique NPAs are allowed between the MR, NT, and TD record codes. 200-999 = NPA code as defined on Record Codes MR and TR ONl-ON4= on-net code as defined on Record Codes AC and TR D-2588187SVR 5210
- -TL-130400-1001 MESSAGE13.0 This section describes the record codes required to DETAIL RECORDERdefine the system MDR (Message Detail Recorder) feature. The following record codes are required: l Record Code MD defines the requirements for the MDR devices, __l Record Code MT defines the TTY requirements. .-..l Record Code Sl defines the screening options. l Record Code S2 defines additional screening options. SVR 5210 8187D-259
TL-130400-1001Record Code MD:13.1 Record Code MD, Figure 13.1, defines the requirements for Message Detailthe MDR devices. Recorder ‘---------T-----T-------------------------~-----~-----7---,-----__--------___II I TI II I4 I I4I I1I I ’ ’ I’ ’ I I’ ’ III hI’ E’ ’ I’ ’ I’ ’ I’ ’ I’ ’ I’ ’ I’ ’ I ’ ’ I c-+-+-u-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-~l3lOlOI,,,,,i,I I I I I I I I I I I I I I I I,, I I I I I l I I I I I I I I I IL-*-L--U--L-~-I-~--C--C-~-I-~-~-~--L-~-I--L-I-*-*-~-I-*-~-~-~-~-~-~-~-~--l--U Figure 13.1Record Code MD: Message Detail Recorder Data Sheet Table 13.1Entry Fields for Record Code MDCOMMENTS a trunk does not have answer supervision, s timing value is used to estimate how much me it takes for a two-way connection to be If answer supervision is provided (for all If the device used for the MDR function is a remote pollingdevice (CRT), enter Y in this D-2608167SVR 5210
TL-130400-1001Table 13.1Entry Fields for Record Code MD (Continued)COMMENTS for each colufor each colustem andits physicallocation within the ed by the telephone company. represents the billing number of Duration for a -255 =numberIndicate theminimumnumber of seconds that a call must be connected before a call record is produced at the MDR terminal. -Calls that last less than this amount of time are not recorded. -If this timing parameter is met, a record of the call is made whether or not the call was actually answered. -The value of this field is added to the value given in columns 12-14 when listing the length of the call. 31-33Minimum Call001-255 = numberIndicate the minimum number of seconds that Duration for a--- = N/Aa call must be connected before a call record Remote Pollingis produced at the remote polling device. Device-Calls that last less than this amount of time are not recorded. -If this timing parameter is met, a record of the call is made whether or not the call was actually answered. The value of this field is added to the value given in columns 12-14 when listing the length of the call. 34 Output FormatY = EBCDIC formatThis field determines the format of the MDR - = TTY formatoutput.-For normal applications, the entry is TTY. 35Output theY = allowedEnter Y if a second line output of the call Second Line of - = not allowedrecord to MDR port 0 is allowed. the Call Record-Do not specify this if the MDR data is to MDR Port 0transmitted to a remote processor (COMDEV or other) that requires single line output format. SVR 5210 8187D-261
TL-130400-1001 Record Code MT:13.2 Record Code MT, Figure 13.2, defines the requirements forMessage Detailthe MDR (Message Detail Recorder) TTY unit interfacing Recorder Portthe system. r---------r-r-----------------------------~---------------------------------~ I; II II II IIIIIIFigure 13.2Record Code MT: Message Detail Recorder Port Data Sheet Table 13.2 Entry Fields for Record Code MT COL.COL.NO.NAME 12Port Number Transmission Rate1 22-24 1 Input Timeout Security Lock TimeoutVALID ENTRIES 0= MDR call records (ASCII) 1 = MDR call record blocks (GTE-modified EBCDIC) -=N/A m-v = N/AIS = in service OS = out of service m-w = N/ACOMMENTS This field determines the MDR format output. This field can only be dashed. This field can only be dashed. Is the card in service or out of service? This field can only be dashed. This field can only be dashed. D-2628187SVR 5210