GTE Omni Si Database Technical Practices Manual
Have a look at the manual GTE Omni Si Database Technical Practices Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
TL-130200-1001 FAULT CODE 19(FAULTCODE1S)REMOVE FUSE FROM BATTERY PACK &POWER DOWN . .SYSTEM 1 R&R Ml MB IN Y/O1 FB-17314 (Check Strapping) POWER UPAND RELOAD MONITOR PSUPY FOR“ASW” TO LIGHT IYES INO T*POWER DOWN & REINSTALL ORIGINAL Ml MB CARD LR&R MPG16 IN Y/O2 FB-1721’3 (Check Strapping) POWER UPAND RELOAD &MONITOR PSUPY FOR“ASW” TO LIGHT REPLACE FUSEIN BATTERY PACK5210 a/a7M-135
TL-130200-1001 Fault Code 22Description:MDR SDC FaultAn ambiguous MDR port assignment exists. M-l 36 Register Data as System Prints:CECO CECO Fault 22 B C D E H L FF 00 00 PEC Number (Always 0) 05= Improper SDC port assignment LFault Resolution Steps: 1.Reload system - depress reset on PSUPY card. 2.If terminal records output on port 0, mark MDR port 0 in service in Table T4551; port 1 must be marked out of service; back up the data base. 3.If terminal records output on port 1, mark MDR port 1 in service in Table T4551; port 0 must be marked out of service; back up the data base. 4.Connect the output device to the MDR SDC output port (the port which is not marked as maintenance). 5.Warm start the system - cycle main circuit breaker at rear of OMNI SI cabinet. 6.Place a trunk call which should be recorded by MDR. 7.If no MDR output, ask for assistance. NOTE: MDR SDC port transmission data is derived from Table T6051. 81875210
TL-130200-1001 FAULT CODE - 22 FAULT CODE 22 fREGISTER C = 05 RELOAD SYSTEM - DEPRESS “RESET” ON PSUPY IN P/O1 1MARK MDR PORT 0 IN SERVICE IN PORT YESMARK MDR PORT 1 IN SERVICE IN NO ICONNECT THE OUTPUT DEVICEI LTO THE MDR SCD OUTPUT PORT+(THE PORT WHICH IS NOT MARKED AS MAINTENANCE) WARM START THE SYSTEM -CYCLE MAIN CIRCUIT BREAKER AT REAR OF St CABINET IF NO MDR OUTPUT, ASK FOR ASSISTANCE. NOTE: MDR SDC PORT TRANSMISSION DATA IS DERIVED FROM TABLE T6051. 52108187M-137
TL-130200-1001Fault Code 25Description: Real-Time Clock FailureThis fault indicates a problem with the Real-Time Clock which is part of the CPU85 card.. Register Data as System Prints:CECO CECO Fault 25 B C D E H L \xx/ 00 00 00 00 00 I 00= Clock is out of range Fl= Read-after-write error F2= Real time clock problem Fault Resolution Steps: 1.Power down - turn off main circuit breaker at rear of OMNI SI cabinet. 2.Remove and replace CPU85E, FB-17288-A‘ in Y/O4 (check strapping). 3.Power up system. 4.Monitor PSUPY card in P/O1 for ASW LED to light - approximately 15 seconds to warm start. 81875210
TL-130200-1001. ..--.-v-w --FAULT CODE 25 +POWER DOWN SYSTEM. R&R CPU85E FB-I 7288 IN Y/04 (Check Strapping)POWER UP AND RELOAD MONITOR PSUPY FOR “ASW” TO LIGHT 5210 a/a7M-139
TL-130200-1001Fault Code 27Description: Disk Backup FailureWhen a power failure occurs, dynamic memory (containing wake-up, message, etc.) is automatically written to disk topreserve data. This fault indicates that the Hotel/Health Care dynamic data was not backed up onto the disk. M-l 40 Register Data as System Prints:CECO CECO Fault 27 B C D E H L \xx/ xx 00 00 00 00 Y 01= Disk operation failed 02= Disk request failed 00= Disk backup successful 1A= File read failed 1B= File write failed Fault Resolution Steps: 1.Inform customer that the data has been lost and must be reentered. 2.If the problem is hardware related, perform the following procedures: - Power down system - turn off main circuit breaker at rear of OMNI SI cabinet. - Remove and replace FMSD in Y/07, FB-17220-BOA, (check strapping). - Monitor PSUPY for ASW LED to light. ala75210
TL-130200-1001 FAULT CODE - 27 IPOWER DOWN SYSTEMI“ASW” TO LIGHT 5210a/a7M-141
TL-130200-1001 TL-130200-1001Fault Code 30Fault Code 30Description: Description: Attendant Console Attendant ConsoleCommon transmission to an Attendant Console has failed. Common transmission to an Attendant Console has failed. Recovery Recovery Data Check Error Data Check Error _.Register Data as System Prints:CECO CECO Fault 30 B C D E H L ‘X7’ \x7(/ 00 Yxxy 00 00 Console 0 or 108= Check sum 09= Data linkOA = Timeout occurred M-142 M-142 81875210
TL-130200-1001 FAULT CODE - 30 IFAULT CODE 30I INOTE CONSOLE NUMBER1 REGISTER E = ? 1A, 9, OR 8 ANGLE FAULT h A”‘- NO ACTION, IGNORE _ 1NOATTENDANT NO ,]I labREPLACE ATTENDANT CONSOLE 1 YESFORCE ATTENDANT CONSOLE OS AND REMOVE AND REPLACE THE ATT12 CARD. FORCE CONSOLE IN SERVICE.5210 8187M-143
TL-130200-1001Fault Code 32Description: CIPNCIPIDVCIP CardThis fault indicates a failure in the CIPNCIPIDVCIP or VP20 card. FailureM-l 44 Register Data as System Prints:CECO CECO Fault 32 B C D E H L y 9 lxp xx xx xxPECCard NumberNumber (Always 0) (O-15) 00= Card Test Failure 01= Card XMIT Error 02= Card Watch Dog Timer Error 03= Card Hardware Error 04= Card Initialization Error Fault Resolution Steps: 1.Identify CIP/VCIP/DVCIP or VP20 relative card number location by performing a general read of T7053-0, address OB2F thru OB3E (GR D2 OB2F OB3E). OB2F =Relative Cl Card No. 0 OB30 = Relative Cl Card No. 1 OB31 = Relative Cl Card No. 2 0832 = Relative Cl Card No. 3 0833 =Relative Cl Card No. 4 OB34 =Relative Cl Card No. 5 0835 =Relative Cl Card No. 6 0836 =Relative Cl Card No. 7 0837 =Relative Cl Card No. 8 0838 = Relative Cl Card No. 9 OB39 = Relative Cl Card No. 10 OB3A =Relative Cl Card No. 11 OB3B = Relative Cl Card No. 12 OB3C =Relative Cl Card No. 13 OB3D =Relative Cl Card No. 14 OB3E =Relative Cl Card No. 15 2. Interpret contents to indicate physical location of card. 81875210