Xerox 1632 2240 3535 Color Carrera Manual
Have a look at the manual Xerox 1632 2240 3535 Color Carrera Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 228 Xerox manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
6/02 2-31 DC1632/2240 3-353, 3-354 Status Indicator RAPs Prelaunch Training/Review 3-353 IOT-ESS Communication Failure 13Controller received check code error.ProcedureSwitch the power off then on. The problem is corrected. YN Reinstall the software. If the problem continues, check the MCU PWB connectors. If the check is OK, replace the MCU PWB (PL 13.1). Return to Service Call Procedures. 3-354 IOT-ESS Communication Failure 14Controller received check code error.ProcedureSwitch the power off then on. The problem is corrected. YN Reinstall the software. If the problem continues, check the MCU PWB connectors. If the check is OK, replace the MCU PWB (PL 13.1). Return to Service Call Procedures.
6/02 2-32DC1632/2240 3-355, 3-356 Prelaunch Training/Review Status Indicator RAPs 3-355 IOT-ESS Communication Failure 15Controller received check code error.ProcedureSwitch the power off then on. The problem is corrected. YN Reinstall the software. If the problem continues, check the MCU PWB connectors. If the check is OK, replace the MCU PWB (PL 13.1). Return to Service Call Procedures. 3-356 IOT-ESS Communication Failure 16Controller received check code error.ProcedureSwitch the power off then on. The problem is corrected. YN Reinstall the software. If the problem continues, check the MCU PWB connectors. If the check is OK, replace the MCU PWB (PL 13.1). Return to Service Call Procedures.
6/02 2-33 DC1632/2240 3-357, 3-358 Status Indicator RAPs Prelaunch Training/Review 3-357 IOT-ESS Communication Failure 17Controller received check code error.ProcedureSwitch the power off then on. The problem is corrected. YN Reinstall the software. If the problem continues, check the MCU PWB connectors. If the check is OK, replace the MCU PWB (PL 13.1). Return to Service Call Procedures. 3-358 IOT-ESS Communication Failure 1Controller received check code error.ProcedureSwitch the power off then on. The problem is corrected. YN Reinstall the software. If the problem continues, check the MCU PWB connectors. If the check is OK, replace the MCU PWB (PL 13.1). Return to Service Call Procedures.
6/02 2-34DC1632/2240 3-359 , 3-360 Prelaunch Training/Review Status Indicator RAPs 3-359 IOT-ESS Communication Failure 19Controller received check code error.ProcedureSwitch the power off then on. The problem is corrected. YN Reinstall the software. If the problem continues, check the MCU PWB connectors. If the check is OK, replace the MCU PWB (PL 13.1). Return to Service Call Procedures. 3-360 IOT-ESS Initialization FailureController received check code error.ProcedureSwitch the power off then on. The problem is corrected. YN Reinstall the software. If the problem continues, check the MCU PWB connectors. If the check is OK, replace the MCU PWB (PL 13.1). Return to Service Call Procedures.
6/02 2-35 DC1632/2240 3-364, 3-370 Status Indicator RAPs Prelaunch Training/Review 3-364 DMA Transfer FailureCompression/extraction did not complete.ProcedureSwitch the power off then on. The problem is corrected. YN Replace the RAM (PL13.1) then the HDD. If the problem continues, replace the ESS PWB (PL 13.1). Return to Service Call Procedures. 3-370 Marker Code Detect FailureThe end code cannot be found in the compressed data.ProcedureSwitch the power off then on. The problem is corrected. YN Replace the RAM (PL13.1) then the HDD. If the problem continues, replace the ESS PWB (PL 13.1). Return to Service Call Procedures.
6/02 2-36DC1632/2240 3-747, 3-750 Prelaunch Training/Review Status Indicator RAPs 3-747 Print Instruction FailureThe print parameter is incorrect.ProcedureSwitch the power off then on. The problem is corrected. YN Change the print parameter and print again. Return to Service Call Procedures. 3-750 Insufficient Number of Document PagesInsufficient number of pages programed when making a book.ProcedureSwitch the power off then on. The problem is corrected. YN Set the number of document pages to the maximum count. Return to Service Call Procedures.
6/02 2-37 DC1632/2240 3-761, 3-941 Status Indicator RAPs Prelaunch Training/Review 3-761 Tray Select ErrorThe paper sizes are different than the tray that will be selected by the APS.ProcedureSwitch the power off then on. The problem is corrected. YN Select an appropriate tray. Return to Service Call Procedures. 3-941 Insufficient Page MemoryProcedureSwitch the power off then on. The problem is corrected. YN Perform the operation again. Return to Service Call Procedures.
6/02 2-38DC1632/2240 3-942, 3-946 Prelaunch Training/Review Status Indicator RAPs 3-942 Document Size ErrorProcedureSwitch the power off then on. The problem is corrected. YN Perform the operation again. Return to Service Call Procedures. 3-946 Tray 1 Not In PositionTray 1 not in ready position.Initial Actionsï Check that the paper size setting is correct. ï Check the Paper Size Sensor for obstructions or damage.ProcedureEnsure Tray 1 is closed. The voltage measured at P/J536-B9 on the I/F PWB corresponds to the paper size in the table. YN There is +3.3VDC measured at P/J536-B10. YN Check the connection between the I/F PWB and the MCU PWB. If the check is OK, replace the I/F PWB (PL 9.1). If the problem continues, replace the MCU PWB (PL 13.1) Check the wires and connectors. If the check is OK, replace the Tray 1 Paper Size Sensor (PL 2.1). Check the connection between I/F PWB and MCU PWB. If the check is OK, replace the MCU PWB (PL 13.1). Figure 1 Tray 1 Paper Size Sensor
6/02 2-39 DC1632/2240 3-947, 3-948 Status Indicator RAPs Prelaunch Training/Review 3-947 Tray 2 Not In PositionTray 2 not in ready position.Initial Actionsï Check that the paper size setting is correct. ï Check the Paper Size Sensor for obstructions or damage.ProcedureEnsure Tray 2 is closed. The voltage measured at P/J546-8 on the Tray Module PWB (PL 16.15) corresponds to the paper size in the table. YN There is +5VDC measured at P/J546-9 on the Tray Module PWB (PL 16.15) YN Check the wires and connectors. If the check is OK, replace the Tray Module PWB (PL 16.15) Check the wires and connectors. If the check is OK, replace the Tray 2 Paper Size Sensor (PL 16.1). Check the wires and connectors, If the check is OK, replace the Tray Module PWB (PL 16.15). If the problem continues, replace the Tray 2 Paper Size Sensor (PL 16.1). Figure 1 Tray 2 Paper Size Sensor 3-948 Tray 3 Not In PositionTray 3 not in ready position.Initial Actionsï Check that the paper size setting is correct. ï Check the Paper Size Sensor for obstructions or damage.ProcedureEnsure Tray 3 is closed. The voltage measured at P/J548-11 on the Tray Module PWB (PL 16.15) corresponds to the paper size in the table. YN There is +5VDC measured at P/J548-12 on the Tray Module PWB (PL 16.15) YN Check the wires and connectors. If the check is OK, replace the Tray Module PWB (PL 16.15) Check the wires and connectors. If the check is OK, replace the Tray 3 Paper Size Sensor (PL 16.1). Check the wires and connectors, If the check is OK, replace the Tray Module PWB (PL 16.15). If the problem continues, replace the Tray 3 Paper Size Sensor (PL 16.1). Figure 1 Tray 3 Paper Size Sensor
6/02 2-40DC1632/2240 3-949, 3-950 Prelaunch Training/Review Status Indicator RAPs 3-949 Tray 4 Not In PositionTray 4 not in ready position.Initial Actionsï Check that the paper size setting is correct. ï Check the Paper Size Sensor for obstructions or damage.ProcedureEnsure Tray 4 is closed. The voltage measured at P/J548-5 on the Tray Module PWB (PL 16.15) corresponds to the paper size in the table. YN There is +5VDC measured at P/J548-6 on the Tray Module PWB (PL 16.15) YN Check the wires and connectors. If the check is OK, replace the Tray Module PWB (PL 16.15) Check the wires and connectors. If the check is OK, replace the Tray 2 Paper Size Sensor (PL 16.1). Check the wires and connectors, If the check is OK, replace the Tray Module PWB (PL 16.15). If the problem continues, replace the Tray 4 Paper Size Sensor (PL 16.1). Figure 1 Tray 4 Paper Size Sensor 3-950 Tray 1 No PaperNo paper in Tray 1ProcedureEnter dC330 [007-120] and press Start. Actuate Tray 1 No Paper Sensor. The display changes state. YN Go to OF 99-2 Transmissive Sensor RAP, repair Tray 1 No Paper Sensor (PL 2.4). Replace MCU PWB (PL 13.1). Figure 1 Tray 1 No Paper Sensor CD