Xerox 1632 2240 3535 Color Carrera Manual
Have a look at the manual Xerox 1632 2240 3535 Color Carrera Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 228 Xerox manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
6/02 2-371 DC1632/2240 116-324, 116-325 Status Indicator RAPs Prelaunch Training/Review 116-324 Exception ErrorCPU exceptional error.ProcedureSwitch power off then on. The problem continues. YN Return to Service Call Procedures. Replace the ESS PWB (PL 13.1). 116-325 Communication Error+24 VDC enabled Communications failure.Procedure+24 VDC power is failed. Status Code 102-319 is displayed after 116-325 is displayed. YN Preliminary information not available. +24V LVPS is failed. Perform following: ï Remove Rear Cover (REP 14.2). ï Remove cover from +24V LVPS (PL 9.1). ï Disconnect P502 on +24V LVPS (Figure 1). Check that power is switched off. Measure resistance of fuse on +24V LVPS. Resistance is 1 ohm or less. YN Replace +24V LVPS (PL 9.1). Switch on the power. Measure the AC voltage between the white and black wires in P2 on the +24 VDC. 110 or 220 VAC is measured. YN Go to the AC Power RAP. Connect the black meter lead to DC COM or frame. Measure DC voltage at P505 on the +24 V LV P S (Figure 1). Voltages are measured as shown. YN There is a problem with the +24 VDC enable circuit. Go to the +24 VDC Enable RAP. Measure the DC voltage at P502 on the +24V LVPS (Figure 1). Voltages are measured as shown. YN Replace the 24V LVPS (PL 9.1). There is a short circuit in +24 VDC distribution. Go to the +24 VDC Short Circuit RAP. Figure 1 P502, P505 on +24V LVPS +24V, 0V, +3.5V, +5V +24 VDC RET Vio (all on top)+24 VDC Orn (all)
6/02 2-372DC1632/2240 116-326, 116-327 Prelaunch Training/Review Status Indicator RAPs 116-326 ESS ROM DIMM #1 FlashA failure was detected in the ESS ROM DIMM #1 Flash.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Pull out and insert the ESS ROM DIMM #1. If the problem continues, replace the ESS ROM DIMM #1. 116-327 ESS ROM DIMM #2 FlashA failure was detected in the ESS ROM DIMM #2 Flash.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Pull out and insert the ESS ROM DIMM #2. If the problem continues, replace the ESS ROM DIMM #2.
6/02 2-373 DC1632/2240 116-328, 116-329 Status Indicator RAPs Prelaunch Training/Review 116-328 L2 CacheA L2 Cache failure was detected.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Replace the ESS PWB (PL 13.1). 116-329 Serial I/F SoftThe system call error related to the serial I/F was detected.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Again, switch the power off then on.
6/02 2-374DC1632/2240 116-330, 116-332 Prelaunch Training/Review Status Indicator RAPs 116-330 HD File SystemThe system detected that the an error has occurred or the HD was not formatted during HD check at power on.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Run the HD Diag (DC355). If the problem continues, replace the HD (PL 13.1). If the problem continues, replace the ESS PWB (PL 13.1). 116-332 Invalid Log InfoA failure related to log was detected.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. After removing the HD and switching power off then on. Install the HD again and turn the power on. If the problem continues, run the HD Diag (DC355). If the problem continues, replace the ESS PWB (PL 13.1).
6/02 2-375 DC1632/2240 116-333, 116-335 Status Indicator RAPs Prelaunch Training/Review 116-333 LocalTalk SoftDue to an error during the software processing, the subsequent processes cannot be per- formed.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Perform re-installation of the ESS software. If the problem continues, replace the ESS PWB (PL 13.1). 116-335 MFIO HDHD failure to be detected by MFIOProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Set up the HD. If the problem continues, replace the HD (PL 13.1). If the problem continues, replace the ESS PWB (PL 13.1).
6/02 2-376DC1632/2240 116-336, 116-337 Prelaunch Training/Review Status Indicator RAPs 116-336 Redirector HDHD failure to be detected by RedirectorProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Set up the HD. If the problem continues, replace the HD (PL 13.1). If the problem continues, replace the ESS PWB (PL 13.1). 116-337 Template HD Write Error An error has occurred when the Job Template was stored in the local HD.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Set up the HD. If the problem continues, replace the HD (PL 13.1). If the problem continues, replace the ESS PWB (PL 13.1).
6/02 2-377 DC1632/2240 116-340, 116-341 Status Indicator RAPs Prelaunch Training/Review 116-340 Short of MemoryWhen the system detected that the memory was insufficient.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Add memory Pull out PostScript option. 116-341 ROM DIMMs Mismatchseveral invalid ROM DIMM versions that are installed The combination of the installed ROM DIMMs is invalid for use at the same time. When installing multiple ROM DIMMs, it is neces- sary to match the major version with the minor version.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Replace PS-1 and PS-2 ROM.
6/02 2-378DC1632/2240 116-342, 116-344 Prelaunch Training/Review Status Indicator RAPs 116-342 JT MonitorFatal errors to be detected by the JT monitorProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Replace the ESS PWB (PL 13.1). 116-344 MF IOFatal errors to be detected by MFIOProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Replace the ESS PWB (PL 13.1).
6/02 2-379 DC1632/2240 116-345, 116-346 Status Indicator RAPs Prelaunch Training/Review 116-345 Token Ring Board Token Ring Control IC Access errorProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Again, switch power off then on. Return to service call procedures. 116-346 FormatterFatal errors to be detected by the Formatter were detected.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Replace the ESS PWB (PL 13.1).
6/02 2-380DC1632/2240 116-348, 116-349 Prelaunch Training/Review Status Indicator RAPs 116-348 RedirecterFatal errors to be detected by RedirecterProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Replace the ESS PWB (PL 13.1). 116-349 SIF on Calling Pflite FunctionAn error has occurred when calling the Pflite function with SIF.ProcedureSwitch power off then on. The problem continues. YN Return to service call procedures. Replace the ESS PWB (PL 13.1).