Home > NEC > Communications System > NEC Mcu 5000a Multipoint Control Unit Equipment Manual

NEC Mcu 5000a Multipoint Control Unit Equipment Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual NEC Mcu 5000a Multipoint Control Unit Equipment Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 702
    Add page 451 to Favourites
    image text
    Enable zoom 
    							NECA 340-4 14- 30 0  Revisio n 2.0   Page 1 o f 2
MCU  5000A Multipoint Control  U nit   COP-138
RCNN
BCONn
UCONn [n … ]
LCONn [n … ]
MCONn  … [MnSs …  ]
MCNR nRx
B CON7
UCON356
MCON8101112
    Add page 452 to Favourites
    image text
    Enable zoom 
    							Page 2 of 2 NECA 340-414-300 Revision 2.0
COP-138 MCU 5000A Multipoint Control Unit
This page is for your notes.
    Add page 453 to Favourites
    image text
    Enable zoom 
    							NECA 340-414-300 Revision 2.0 Page 1 of 2
MCU 5000A Multipoint Control Unit COP-139
MCON
Mutlipoint/Lecture Connection Control
COMMAND NAME
Multi point CONnect
PURPOSE
This command is used to establish H.320 multipoint connections.  The specified 
terminal (room) can participate in the multipoint teleconference.  When the line 
number is set to 0, line connection is not established and the teleconference room 
number is skipped.  In the cascade connection, the MCU acts as a master-side.
INPUT FORMAT
MCON     nm1     nm2     nm3 … [Mnc     Snx     ns1     ns2 … ][     Rr][__S] ¿
EXPLANATION OF INPUT PARAMETERS
n
i =1 ~ 254
Specifies the logic line number of the terminal to be multi-
connected.  
i = m
jSpecifies the terminal logic line number to be connected in the 
Master MCU.
i = x Specifies the slave number.
i = s
jSpecifies the terminal logic line number  to be connected to 
Slave-side MCU.
i = c Specifies the logic line number of cascade port.
r = Specifies a bit rate (kb/s).  Note that a bit rate corresponds to the 
type of line interface.  If this parameter is no value (not entered), 
the default bit rate (system parameter value) is used.  Valid values 
for r are:
56, 56X2, 64, 64X2, 112, 128, 168, 192, 224, 256, 336, 384, 448, 512, 
672, 768, 1008, 1152, 1344, 1536, 1920, 1472, 1288, 384x2, 336x2
S = B, 2B, H0, or 2H0
Specifies the line speed.
    Add page 454 to Favourites
    image text
    Enable zoom 
    							Page 2 o f 2   NECA 340 -41 4-3 00 Revisi on  2.0
CO P-139   MCU 5000A Mult ipoint Con trol Unit
MCON
mmx kb psOK
2345 ¿
010203043 84 kbpsOK
    Add page 455 to Favourites
    image text
    Enable zoom 
    							NECA 340-4 14- 30 0  Revisio n 2.0   Page 1 o f 2
MCU  5000A Multipoint Control  U nit   COP-140
MDSC
g] ¿
A ¿
    Add page 456 to Favourites
    image text
    Enable zoom 
    							Page 2 of 2 NECA 340-414-300 Revision 2.0
COP-140 MCU 5000A Multipoint Control Unit
This page is for your notes.
    Add page 457 to Favourites
    image text
    Enable zoom 
    							NECA 340-414-300 Revision 2.0 Page 1 of 2
MCU 5000A Multipoint Control Unit COP-141
ECON
Mutlipoint/Lecture Connection Control
COMMAND NAME
*Education mode multi point CONnection
PURPOSE
This command is used to establish a multipoint connection in an education mode.  
In this connection, voice activated switching is deactivated.
INPUT FORMAT
ECON     [I]nm1     [I]nm2     [I]nm3 … [Mnc     Snx     [I]ns1     [I]ns2 … ][     Rr][     s] ¿
EXPLANATION OF INPUT PARAMETERS
n
i=1 ~ 254
Specifies the logic line number of the terminal to be multi-
connected.  
i=m
jSpecifies the logic line number of the terminal to be connected to 
Master-side MCU.
i=x Specifies the slave number.
i=s
jSpecifies the logic line number of the terminal to be connected to 
Slave-side MCU.
i=c Specifies the logic line number of the cascade port.
I: Specifies an instructor terminal.  I should be entered for an 
instructor terminal. 
Note:
Each group can provide only one instructor terminal.  The 
instructor terminal is not set to voice terminal.
r= Specifies the bit rate (kbps).  Note that the bit rate corresponds to 
the type of line interface.  If this parameter is no value (not entered), 
the default bit rate (system parameter value) is used.  Valid values 
for r are:56, 56X2, 64, 64X2, 112, 128, 168, 192, 224, 256, 336, 
384, 448, 512, 672, 768, 1008, 1152, 1344, 1536, 1920, 1288, 1472, 
384X2, 336X2
S: B, 2B, H0, or 2H0
Specifies the line speed
*Future Release
    Add page 458 to Favourites
    image text
    Enable zoom 
    							Page 2 o f 2   NECA 340 -41 4-3 00 Revisi on  2.0
CO P-141   MCU 5000A Mult ipoint Con trol Unit
ECON
[ I]m[ I]mxkb psOK
2I345 ¿
02I030405384k bpsOK
    Add page 459 to Favourites
    image text
    Enable zoom 
    							NECA 340-4 14- 30 0  Revisio n 2.0   Page 1 o f 2
MCU  5000A Multipoint Control  U nit   COP-142
EDSC
g] ¿
A ¿
    Add page 460 to Favourites
    image text
    Enable zoom 
    							Page 2 of 2 NECA 340-414-300 Revision 2.0
COP-142 MCU 5000A Multipoint Control Unit
This page is for your notes.
    All NEC manuals Comments (0)

    Related Manuals for NEC Mcu 5000a Multipoint Control Unit Equipment Manual