NEC Mcu 5000a Multipoint Control Unit Equipment Manual
Have a look at the manual NEC Mcu 5000a Multipoint Control Unit Equipment Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 391
NECA 340-414-220 Revision 2.0 Page 1 of 2
MCU 5000A Multipoint Control Unit SPR-118
VIDEO MODE SETTING
TERMINAL MODE RELATED
SUMMARY:
Specify whether video mode is set or not.
STEP PROCEDURE
Note:
Use the factory shipment value (08H 00H
) in setting the video mode as a general rule. If
change is necessary for any reason, follow the steps described below.
1 Enter the following command.
SSPR__ n1 = x1 __n2 = x2 __ … ni = xi … ¿
ni:
System parameter addressA: 238H and 239H
B: 298H and 299H
[1] Addresses...](http://img.usermanuals.tech/thumb/54/84243/w64_nec-mcu-5000a-equipment-manual_d-390.png "Page 391
NECA 340-414-220 Revision 2.0 Page 1 of 2
MCU 5000A Multipoint Control Unit SPR-118
VIDEO MODE SETTING
TERMINAL MODE RELATED
SUMMARY:
Specify whether video mode is set or not.
STEP PROCEDURE
Note:
Use the factory shipment value (08H 00H
) in setting the video mode as a general rule. If
change is necessary for any reason, follow the steps described below.
1 Enter the following command.
SSPR__ n1 = x1 __n2 = x2 __ … ni = xi … ¿
ni:
System parameter addressA: 238H and 239H
B: 298H and 299H
[1] Addresses...")
NECA 340-414-220 Revision 2.0 Page 1 of 2 MCU 5000A Multipoint Control Unit SPR-118 VIDEO MODE SETTING TERMINAL MODE RELATED SUMMARY: Specify whether video mode is set or not. STEP PROCEDURE Note: Use the factory shipment value (08H 00H ) in setting the video mode as a general rule. If change is necessary for any reason, follow the steps described below. 1 Enter the following command. SSPR__ n1 = x1 __n2 = x2 __ … ni = xi … ¿ ni: System parameter addressA: 238H and 239H B: 298H and 299H [1] Addresses (hexadecimal values) in setting the video mode. The video mode is set in hexadecimal values by dividing the 16 bits (b0 to b15) into the upper-half and lower-half 8 bits, or specifically by setting bit 3 in the lower-half 8 bits to “1” or “0”. Accordingly, since the upper-half 8 bits are always “00H”, set only the lower-half 8 bits (address 128H). ADDRESS VIDEO MODE A: 238H, B: 298H Lower-half 8 bits setting address (b0 to b7) A: 239H, B: 299H Upper-half 8 bits setting address (b8 to b15) xi: System parameter values See below: [1] System parameter values on setting the video mode for the addresses. The factory shipment value for the system parameter is 08H 00H . SYSTEM PARAMETER VIDEO MODE ADDRESS A: 239H B: 299HADDRESS A: 238H B: 298H 00H 00H OFF 00H 08H ON (H.261 video)
Page 2 of 2 NECA 340-414-220 Revision 2.0 SPR-118 MCU 5000A Multipoint Control Unit VIDEO MODE SETTING TERMINAL MODE RELATED STEP PROCEDURE 2 Verify that the normal response is displayed with “OK ”. If YES , go to Step 3 . If NO , go to Step 1 . 3 End of procedure.
NECA 340-414-220 Revision 2.0 Page 1 of 2 MCU 5000A Multipoint Control Unit SPR-119 LSD MODE SETTING TERMINAL MODE RELATED LSD Mode (A: +23AH ~ 23BH) (B: +29AH ~ +29BH) b7 b6b5 b4 b3 b2 b1 b0 b2 : 1200 bps b3 : 4800 bpsDefault = 00H A: +23AH 00 0 fixed0000 fixed 0 fixed b4 : 6400 bps b6 : 9600 bps B: +29AH b7 : 14,400 bps Note: When distributing LSD date, b7, b6, b4, b3 or b2 will be 1. b7 b6b5 b4 b3 b2 b1 b0 Default = 00H 0 fixed0 fixed 0 fixed0 fixed 0 fixed 0 fixed 0 fixed0 fixed A: +23BH B: +29BH
Page 2 of 2 NECA 340-414-220 Revision 2.0 SPR-119 MCU 5000A Multipoint Control Unit This page is for your notes.
NECA 340-414-220 Revision 2.0 Page 1 of 2 MCU 5000A Multipoint Control Unit SPR-120 HSD CAPABILITY SETTING TERMINAL MODE RELATED HSD Capability (A: +23CH ~ 23FH) (B: +29CH ~ +29FH) b7 b6b5 b4 b3 b2 b1 b0 Default = 00H 0 fixed0 fixed 0 fixed0 fixed 0 fixed 0 fixed 0 fixed0 fixed A: +23CH B: +29CH b7 b6b5 b4 b3 b2 b1 b0 Default = 00H 0 fixed000 0 0 A: +23DH B: +29DH b1 : 64 kbps b2 : 128 kbps b3 : 192 kbps b4 : 256 kbps b6 : 384 kbps Note: When distributing HSD date, bit will be 1.0 fixed b7 b6b5 b4 b3 b2 b1 b0 Default = 00H 0 0 fixed0 A: +23EH B: +29EH b0 : 768 kbps (R) b2 : 1536 kbps (R) Note: When distributing HSD date, bit will be 1.0 fixed 0 fixed 0 fixed 0 fixed 0 fixed b7 b6b5 b4 b3 b2 b1 b0 Default = 00H A: +23FH B: +29FH0 fixed0 fixed 0 fixed0 fixed 0 fixed 0 fixed 0 fixed0 fixed
Page 2 of 2 NECA 340-414-220 Revision 2.0 SPR-120 MCU 5000A Multipoint Control Unit This page is for your notes.
NECA 340-414-220 Revision 2.0 Page 1 of 2 MCU 5000A Multipoint Control Unit SPR-121 MLP MODE SETTING TERMINAL MODE RELATED MLP Mode (A: +240H ~ 241H) (B: +2A0H ~ +2A1H) Note: MCU 5000A does not support MLP, when RCON mode. b7 b6b5 b4 b3 b2 b1 b0 Default = 00H 0 fixed0 fixed 0 fixed0 fixed 0 fixed 0 00 fixed A: +240H B: +2A0H b1 : MLP-4k b2 : MLP-6.4k b7 b6b5 b4 b3 b2 b1 b0 Default = 00H 0 fixed0 fixed 0 fixed0 fixed 0 fixed 0 fixed 0 fixed0 fixed A: +241H B: +2A1H
Page 2 of 2 NECA 340-414-220 Revision 2.0 SPR-121 MCU 5000A Multipoint Control Unit This page is for your notes.
NECA 340-414-220 Revision 2.0 Page 1 of 2 MCU 5000A Multipoint Control Unit SPR-122 NETWORK CLASSIFICATION MODE SETTING TERMINAL MODE RELATED Network Classification Mode (A: +242H ~ 243H) (B: +2A2H ~ +2A3H) b7 b6b5 b4 b3 b2 b1 b0 Default = 01H 0 fixed0 fixed 0 fixed0 fixed 0 fixed 00 fixed A: +242H B: +2A2H b0 : 64 kbps (unrestricted) b1 : 56 kbps (restricted) 0 fixed b7 b6b5 b4 b3 b2 b1 b0 Default = 00H 0 fixed0 fixed 0 fixed0 fixed 0 fixed 0 fixed 0 fixed0 fixed A: +243H B: +2A3H
Page 2 of 2 NECA 340-414-220 Revision 2.0 SPR-122 MCU 5000A Multipoint Control Unit This page is for your notes.