Toshiba Strata Dk14, Dk40i, Dk424 Installation And Maintenance Manual

							Strata AirLink Systems
RWIU System Installation
Strata DK I&M 5/9916-39
Strata AirLink Systems
 
Important!For Strata DK40i, if there are 8 handsets, the RWIU can be installed in any of the 
expansion cabinet slots (15, 16, and 18). If there are 16 handsets, the RWIU must be 
installed in slot 15 and Slot 16 must be vacant. This system cannot support 24 or 32 
handsets because of a port limitation.
Step 4: Install the RWIU/WWIS into the Strata DK
1. Insert the RWIU (WWIS and components facing right) into the appropriate slot of the Strata 
DK and apply firm, even pressure to ensure proper mating of connectors.
CAUTION!Strata DK power must be off before inserting the RWIU.
2. After installing the RWIU, gently pull the PCB outward. If the connectors are properly seated, 
a slight resistance is felt.
Step 5: Run the Cable
1. Do not exceed these cabling distances between the Base Stations and WWIS for Category 5, 
24 AWG:
©2,000 feet for line power
©3,300 feet for local power
2. Use Category 5 cable. Using a mix of Categories 2, 3, 4, and 5 is acceptable but can effect the 
total possible cable length.
Table 16-14 Strata DK424 and DK280 Base and Expansion Cabinet Slot Assignments
CabinetPhysical
SlotsVacant
Slots
NumberTy p e
1 DK424 Base 13~1613/14
1
1. Slot must be vacant for RWIU handsets 9~16 (2 slot RWIU positions).15/16
1
2 DK424 21~2821/22123/24125/261/272/28
2 DK280 21~2621/22
123/24125/261
3 DK424 31~3831/32133/341/352/363
2. Slot must be vacant for RWIU handsets 17~24 (3 slot RWIU positions).
3. Slot must be vacant for RWIU handsets 25~32 (4 slot RWIU positions).37/38
1
3 DK280 31~3631/32133/341/352/36
4 DK424 41~4841/42
143/441/452/4647/481
4 DK280 41~4641/42143/441/452/46
5 DK424 51~5851/52
153/541/552/5657/581
5 DK280 51~5651/52153/541/552/56
6 DK424 61~6861/62
163/641/652/6667/681
6 DK280 61~6661/62163/641/652/66
7 DK424 71~7871/72
173/741/752/7677/781
7 DK280 Cannot be seventh cabinet 
						

							Strata AirLink Systems
RWIU System Installation
16-40Strata DK I&M 5/99
3. Connect one end of each cable into the RJ-45 
jacks on the RWIU/WWIS (Point B in Figure 
16-26) and the other end (reversed) into the EMI 
box (Point A in Figure 16-26). The RJ-45 transmit 
and receive pins are shown in Figure 16-25.
4. Connect each end of the other set of cables into 
the RJ-45 jacks of the EMI box (Point C - To Base 
Stations in Figure 16-26) and run the opposite end 
out to the Base Stations.
 
Figure 16-26 EMI Connections to the RWIU/WWIS
CAUTION!
©Do not use bridge taps between the RWIU and Base Stations because of potential 
transmission problems.
©Do not use current-limiting (fuse style) primary protectors on the transmit and 
receive pairs between the RWIU and Base Stations. 
©Do not connect the RWIU to power at this point.
Step 6: Determine Base Station Power Supply
A Base Station can receive input (line) power from the RWIU or an optional local power supply. 
Using a local power supply increases the distance Base Stations can be located from the RWIU.
Customers with 220VAC outlets can:
©Purchase another power cord to fit the universal connector (three-pronged IEC 320 power 
inlet) on the power supply
©Replace the 110VAC plug on the cable with an appropriate 220VAC plug
©Connect a North American 220VAC adapter to the 110VAC plug
RJ-45
Transmit
Receive 12 65 4 3
3512
RJ-45 RJ-45 RJ-45
Figure 16-25 RJ-45 Pin Configuration
RWIU1A (side)
WWIS1A (side)
3724
1234A BC - 
To Base Stations
EMI 
						

							Strata AirLink Systems
RWIU System Installation
Strata DK I&M 5/9916-41
Strata AirLink Systems
Step 7: Connect the Power Supply
The maximum available PBX power for each RWIU PCB is one amp (+5VDC).
1. Use the external power supply (see Figure 16-27) to 
increase the amps for each Base Station.
The power supply has a -40VDC power connector 
for direct connection to the RWIU.
2. Connect to 110VAC power, but do not power on.
Step 8: Use the Proper Power Factor (PF)
äCheck the +5VDC PF using Table 16-15 as a 
reference. Calculation examples are shown in Ta b l e s  
16-16 and 16-17.
NoteThe maximum voltages for the RPSU280A 
Power Supply are 25.0 (+5VDC) and 65.0                
(-24VDC).
 
Table 16-15 Strata DK40i and DK424 PCB and Power Supply PFs
PCB Type+5VDC PF-24VDC PFNotes
IMDU 0.1 0.16
PCOU1, 2 1.9 2.0
PDKU1, 2 0.8 0.3 With 8 DKTs.
PEKU 1.6 0.7 With 8 EKTs.
PEPU 1.1 6.5
PESU 1.5 0.5 With 4 EKTs and 2 SLTs.
PIOU 2.0 6.5
PIOU2 1.1 6.5
PIOUS 0.75 4.0
RSTU/RSTU2 (-24VDC) 1.4 0.5 With 8 SLTs.
R40S 0.0 2.8 Does not use +5VDC.
RATU 1.7 0.3
RBSS 0.6 0.3
RBSS2 0.0 0.3 Does not use +5VDC.
RBSU + RBSS 3.2 0.3
RBSU 2.5 1.0
3923
AC IN
110VAC
Power Cord
DC OUT
40VDC
DC OUT OK
AC/DC OUT
OK
DC/DC OUT
OK
RWIU - 40 VDC
Power Connector
DC IN
24VDC
Backup
Batteries
Figure 16-27 RWIU Power Supply 
						

							Strata AirLink Systems
RWIU System Installation
16-42Strata DK I&M 5/99
RBSU2 0.0 1.0 Does not use +5VDC.
RBUS 0.0 0.3 Does not use +5VDC.
RBUU 0.0 1.0 Does not use +5VDC.
RCIS 0.3 0.1
RCIU, RCIU2 0.7 0.2
RCMS 0.6 0.3
RCOS, RCOS2 1.7 2.0
RCOU (4 CO) 2.5 2.0
RCOU + RCOS (8 CO) 3.6 4.0
RCOU, RCOU2 1.9 2.0
RCTUA 2.0 1.0
RCTUB 4.0 1.0
RCTUBA/BB 4.0 1.9
RCTUC/D 4.5 1.9
RCTUE/F 10.0 1.9
RDDU 2.6 7.0
RDSU/RDSS (-24VDC) 1.1 0.3 With 4 DKTs and 4 SLTs.
RDSU + R48S (-48VDC) 1.1 0.5
RDTU 1.8 1.0
REMU2/PEMU 1.0 7.5
RGLU, RGLU2 2.1 2.5
RMCU 0.7 0.3
RMDS 0.35 0.16 2400 bps MODEM.
RPTU 2.6 1.0
RRCS-12 1.5 1.0
RRCS-4 0.4 0.3
RRCS-8 1.0 0.5
RSIS 0.35 0.15
RSIU 1.0 0.3
RSSU 0.7 0.3
RSTU + R48S (-48VDC) 1.4 1.0 With 8 SLTs.
RSTU2 4.0 2.3 With 8 MWs.
RWIU 9.2 0.0 With 8, 16, 24, or 32 handsets. Table 16-15 Strata DK40i and DK424 PCB and Power Supply PFs
 (continued)
PCB Type+5VDC PF-24VDC PFNotes 
						

							Strata AirLink Systems
RWIU System Installation
Strata DK I&M 5/9916-43
Strata AirLink Systems
 
Step 9: Program the Strata DK
Important!Do not use a DKT that has an intercom button for Speed Dial programming.
1. Determine how many handsets, PDKU ports, and available slots are required before 
programming the Strata DK. Up to 32 handsets per RWIU are allowed.
2. Use the following programs:
©Program 03 for Code 61 (slot assignments).
©Program 32 for Auto Preference.
©Program 39 for flexible button assignments.
©Programs 81~89 for line ringing on the handsets.
©Program 91-9 for automatic PCB recognition.
©Programs *71~73 for DID ringing on specific handsets.
Refer to Strata DK Programming Manual for specific information and Table 16-18 for 
available Strata DK station features.
Table 16-16 Example of Strata DK424 Base Cabinet Configuration with RCTUA4A
PCBQuantity+5VDC PF-24VDC PF
RCTUA4A 1 2.0 1.0
RRCS-4 1 0.4 0.3
PDKU2 2 1.6 0.3
RCOU + RCOS 1 3.6 4.0 (8 COs)
RBSU + RBSS 1 3.2 0.3
RWIU 1 9.0 0.0
Total 7 19.8 5.9
Table 16-17 Example of Strata DK40i Expansion Cabinet Configuration
PCBQuantity+5VDC PF-24VDC PF
RCOU + RSOU 1 3.6 4.0 (8 COs)
RBSU + RBSS 1 3.2 0.3
RWIU 2 18.0 0.0
Total 4 24.8 4.3
Table 16-18 Available Station Features
Feature Name
Account Code Continuous DTMF Tones
Automatic Call Distribution (ACD) DISA Security Code Revision
Automatic Busy Redial (ABR) Do Not Disturb (DND)
Automatic Call Back (ACB) DND Override (receive)
Automatic Hold Exclusive Hold
Automatic Line Selection Door Phone 
						

							Strata AirLink Systems
RWIU System Installation
16-44Strata DK I&M 5/99
Step 10: Connect the PC
äRun the RS-232-C cable to the back 
of the PC (COM port 1) and insert 
the 6-pin connector into the RWIU 
jack (see Figure 16-28).
Busy Override/Busy Station Transfer/Busy 
Station RingingHeadset Interface
Call Forward: Headset Receiver Volume Control
lAll Calls Hearing Aid Compatible
lBusy Liquid Crystal Display (LCD)
lNo Answer Message Waiting Indication
lBusy/No Answer Multiple Message Waiting
lFixed Microphone Control (fixed) - Mute Only
lExternal Microphone Sensitivity Control
Call Park Orbits: Loud Ringing Bell (headset)
lPark/Page Night Lock
Call Pickup: Night Transfer
lNight Bell Off-hook Call Announce (OCA) - Handset Mode
lTenant Ringing Lines (four groups) Page Access
lStation Groups (20 groups, all call types) Phantom Message Waiting Indication
lAny Ringing LIne Pooled Line
lDirected Station (all call types) Private CO Lines
lHeld CO Lines (selectively) Push-button Dialing
lParked Call Release and Release/Answer
lExternal Page Remote Retrieval of Held/Parked Calls
Centrex/PBX Compatible Ringing Line Preference
CO/Centrex Saved Number Redial
Conferencing Timed Reminders
Dial Pulse DTMF Mode Change Toll Restriction Override Code Revision
Direct Station Selection (DSS) User Programmable Feature Buttons
DSS Console Features Table 16-18 Available Station Features
 (continued)
Feature Name
3333
RS-232-C 6-pin Jack
RWIU (side view)
Figure 16-28 RWIU 6-pin Jack 
						

							Strata AirLink Systems
RWIU System Installation
Strata DK I&M 5/9916-45
Strata AirLink Systems
Step 11: Initialize the RWIU
1. Open the RWIU Manager software.
2. Turn on the Strata DK. The RWIU checks Base Station status and connections.
3. Check the LEDs on the Base Stations. If all the LEDs are OFF, the initialization is complete.
4. Check the handsets for dial tone. If there is dial tone, the initialization is complete.
Step 12: Install the RWIU Manager
1. Check the PC hardware/
software against the required 
minimums.Refer to “Check the System Hardware and Software 
Requirements” on Page 16-3.
2. Close any open applications 
in Windows.
3. Insert the RWIU Manager 
floppy disk into the A:\ drive.
4. In Windows 98/95, click Start 
and Run
...or in Windows 3.11/3.1, 
open Program Manager and 
click File and Run.A dialog box displays requesting the location of the setup 
disk.
5. Type A:\Setup and click 
OK.The Windows setup screen warns Windows applications 
should be closed.
6. Click Yes A dialog box displays recommending a destination path of 
C:\Wireless.
...or No if applications need 
to be closed.
7. Click OK  C:\Wireless is accepted as the destination directory.
...or change the destination 
drive/directory.
8.  Click OK. A dialog box displays requesting verification of the 
software location (its program directory or the Windows 
system directory). Using the program directory is 
recommended.
9. Select the program directory.
10. Click OK. The files are copied to the hard disk. A program group is 
created. 
						

							Strata AirLink Systems
RWIU System Installation
16-46Strata DK I&M 5/99
Step 13: Start the RWIU Manager
Step 14: Set General Settings
1. Make sure that the PC is 
connected to the RWIU.
2. From the RWIU program 
group, double-click on the 
Manager icon.
After a few seconds, the Desktop Toolbar displays.
1. From the Desktop Toolbar, 
click the Config icon.
2. Click General Settings and 
assign COM port 1.
3. Click OK.
4. Click System ID.
5. Enter the System ID.
6. Click OK. General Settings window displays.
3347
3348
3349
3351 
						

							Strata AirLink Systems
RWIU System Installation
Strata DK I&M 5/9916-47
Strata AirLink Systems
Step 15: Enter the Handset IDs
Step 16: Enable UTAM
7. Click Time and Date.
8. Enter the Date and time.
9. Click OK.
1. From the Desktop Toolbar, 
click the Config icon.
2. Click User Database.
3. Download the settings from 
the RWIU.Default IDs display.
Handset IDs do not have 
to be in numerical order 
and can be changed at any 
time.
4. Click OK. The Desktop Toolbar displays.
5. Upload the settings to the 
RW IU .The new IDs are saved.
1. From the Desktop Toolbar, 
click the UTAM Activation 
icon.
3354
3746
3356 
						

							Strata AirLink Systems
RWIU System Installation
16-48Strata DK I&M 5/99
Step 17: Store the IDs in the Handset
2. Click Get UTAM Code from 
RW IU .
3. Enter the password 
LABUTAM.
4. Click OK twice. The Desktop Toolbar displays.
5. Click Get UTAM code from 
RW IU .The new 20-digit UTAM activation code displays. Call the 
UTAM Activation desk at (949) 598-4980 between the 
hours of 8:00 a.m. and 5:00 p.m. (Pacific Standard Time), 
Monday through Friday with this number.
6. Click OK. The Desktop Toolbar displays.
7. Click Send UTAM 
Activation Code to RWIU.
8. Input the 10-digit code given 
to you by the Activation Desk
9. Press Enter.“Permission granted successfully” displays. If an error 
message displays, repeat Steps 1~7.
NoteIf UTAM is required, the Base Stations have one 
power LED ON (green), two (center) transmission 
LEDs ON (red), and four additional LEDs that are 
red.
1. Press 
3:5. The handset turns on.
2. Press 
)&1.
3357
3358
MENU
OPERAT ION
12 : 15