Home > Mitel > Communications System > Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 55 Mitel manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 618
    							Shipping, Receiving, and installation InformationILUE9pOORANGE
    (+WYELLOW(-5v)I I
    IIGBEENNELLOWI I I
    INTERCONNECT
    TB301-3
    BROWNI 
    -
    BAY 3
    KAO015ElRlFigure 5-4 Interconnect Card Ground and DC Power Cable Connections
    Page 63 
    						
    							SECTION MITL9109-094-200-NA
    KAO604EOROFigure 5-5 DC Power Cable (PN114904501)
    Page 64 
    						
    							Shipping, Receiving, and Installation Information
    UPPER SUPPORTIIREAR DOOR
    POWER SUPPLV
    KAO580EOROFigure 5-6 Installation of Rear Door Power Supply and Supports
    Page 65 
    						
    							SECTION MITL9109-094-200-NAREAR 
    DbOR.
    FAN ABSEMBLV
    KAOOlBElRZFigure 5-7 Installation of Fan Assembly
    Page 66 
    						
    							Shipping, Receiving, and Installation Information
    CHART 5-10 (CONT’D)
    INSTALL DIGITAL PERIPHERAL BAYStepAction
    7.At rear of cabinet, connect PCM cable to J17A of Bay backplane; connect PCM groundleads to associated 
    faston connectors. In a 336 port system, Bay 3 connects to J17Aand Bay 4 connects to 
    J17B of the COMBO backplane. In a 672 pert system, PCM
    cables come from Bay 0 or from the Intercabinet Cable Assembly (672 port).
    8.At rear of cabinet, cut off cable ties securing power cable to bottom of cabinet in a
    336 port configuration, or to side rail in a 672 port configuration.
    9.Route power cable from AC distribution along inside side of cardfile side plates, tying
    power cable and braided ground cable to cardfile, and connect plug to Bay Power
    SUPPlY.
    10.
    If installing Digital Backplane kit concurrently, proceed to INSTALL DIGITAL
    BACKPLANE ASSEMBLY instructions.
    11.
    12.
    13.Connect signal cables to Bay backplane, route out of cabinet with existing signal’
    cables, and cross connect at MDF.At front of cabinet, attach antistatic wrist strap to your wrist, and install Bay Control
    Card and new peripheral cards.
    Close doors, power up system, and update CDE to include new equipment.
    INSTALL 
    DIGiTAL BACKPLANE ASSEMBLY
    1.
    2.
    3.
    4.
    5.
    6.
    7.
    8.
    Unpack and inspect Digital Backplane kit.Power down system, and open rear door.
    Attach backplane to cardfile with six screws, flat washers, and lock washers (as
    existing Bay); place double tab connector at lower left corner instead of a flat washer.
    Connect two ground wires to Bays, as shown in Figure 5-9, using hex nuts and split
    lock washers. Refer to Figure 5-10 and Figure 5-12 for details of ground connections.
    Open front door and install Bay Power Supply in its slot.At rear of cabinet, cut off cable ties securing power cable to bottom of cabinet in a
    336 port configuration, or to side rail in a 672 port configuration.
    Route Bay AC power cord up inside side of cardfile, tie-wrap in place, and plug into
    Bay Power Supply.
    At rear of cabinet, connect PCM cable between Control Bay backplane and 
    J17A of
    digital peripheral Bay backplane; connect PCM ground leads to associated 
    faston
    connectors.
    9.
    10.Connect signal cables to connectors, and route out of cabinet with existing signal
    cables, and cross connect at MDF.
    At front of cabinet, while wearing the antistatic wrist strap, unpack and install new
    circuit cards.
    11.Close doors, power up system, and update CDE to include new equipment.
    Page 67 
    						
    							SECTION MITLSI 09-094-200-NA
    KA0239E2R2Figure 5-8 Install Digital Peripheral Bay and Panel
    Page 68 
    						
    							Shipping, Receiving, and Installation informationAC LINE
    CORD-, J17APCM CABLES
    WITH GROUNDS
    TO 
    FASTON TABS
    x AC CORDS
    -GROUND WIRES
    _ BRAIDED GROUNDING SHIELD
    KAO23BElROFigure 5-9 Digital Peripheral Bay Connections
    Page 69 
    						
    							SECTION MITL9109-094-200-NA
    KAD107EDAFigure 5-10 Digital Peripheral 
    Cardfile Ground Connection Details
    Page 
    70 
    						
    							Shipping, Receiving, end Installation Information
    Figure 5-l 1 Digital Peripheral Ground Connection DetailsPage 71 
    						
    							SECTION MITL9109-094-200-NA
    KAO240ElRlDIGITAL BAY
    Figure 5-12 Digital Peripheral Backplane Ground Connection Details
    Page 72 
    						
    All Mitel manuals Comments (0)

    Related Manuals for Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual