Home > Mitel > Communications System > Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 55 Mitel manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 618
    							Shipping, Receiving, and Installation InformationTAB1E&M TRUNK MODUL
    FunctionPABX to Line Gain
    3 dB
    -13 dBLine to PABX Gain
    -4 dB-11 
    dBTermination
    600 ohmComplex
    Transmission
    2 wire
    4 wire
    Signaling
    Type 1
    Type 50= open, 
    I= closet,x= not applicable
    E 5-6E SWITCH SETTINGS
    Switches12345678
    oxxxxxxx
    Ixxxxxxx
    xoxxxxxx
    xlxxxxxx
    xx10xxxx
    xx01xxxxxxxxlxxx
    xxxxoxxx
    xxxxxlxx
    xxxxxoxx
    Page 95 
    						
    							SECTION MITL9109-094-200-NA
    ZzEz-
    -D----MUSIC ON
    HOLD/PAGER
    MODULERECEIVER/RELAY
    CONSOLEMODULEMODULE-SWITCH
    LED’s000
    UNIVERSAL CARD
    KAOOZlEOROFigure 5-23 Universal Card and Modules
    Page 96 
    						
    							Shipping, Receiving, and installation Information
    Figure 5-24 Installation of Module onto Universal Card
    Page 
    97 
    						
    							SECTION MITL9109-094-200-NACROSS-CONNECTION
    MODULE MODULE
    FIELD FIELDT/R PAIR
    GN
    T24--LINE
    9.2=
    aCONSOLE
    T3MODULAR
    NO CONNECTIONSJACK
    CONSOLE MODULE
    R3DIGITAL
    LINE
    CARDT2
    R2GN 
    ----
    RSUPERCONSOLE 1000pRCONSOLE 1000pATTENDANT CONSOLE
    NDANT CONSOLE
    I
    MUSIC’ 
    MIAo;;s -IIN1
    , MIB-PA
    SVSTEM
    ICONTACT RATING i ;q$-!300 OHMS,
    MU_SIC-ON_ H_OLp/PAGlNG_ M_OD_UL_E _
    II
    CONTROLIPAIR
    ‘CUSTOMER-SUPPLIED 
    EGUIPMENTL-----------FROM 533 ON BACKPLANE----------_-(UNIVERSAL CABINET ONLV)I
    (NIGHT BELL CONNECTION)
    icil
    Q
    l_CUsToM_ER-S_P_PL~D-N~H~ EELLFROM RELAV ON
    RELAV MODULE
    300 OHMS
    --iz+-K5AK5BEach NO relay contact
    SUBCIRCUIT 5300 OHMSmay be used to control
    STa device, as required.
    RELAV
    KBAK6BSUBCIRCUIT 6RELAY MODULE
    1NOTE 1. All wiring must be done in accordance with the National
    Electrical 
    Code (USA) or Canadian Electrical Code and/orlocal electrical inspection authorities.
    NOTE 2. Refer to Part 
    6 of this Section for Cross-connect Field pin
    numbers for each module; their assignment depends upon
    the position of the Universal Card and Module.
    NOTE 3. This relay contact may be connected only to a secondary
    circuit that has no direct connection to a primary circuit,
    and receives its power from a transformer, 
    cunverter, or
    equivalent isolation device situated within the equipment.NOTE 4. For 336, 456 and 480 port
    configurations, the relay
    for the night ball 
    must be
    in digital bay 1 or 2.
    NOTE 5. For 672 pert configuration,
    the relay for the night bell
    may be in any peripheral bay.
    NOTE 6. The Superconsole 1000” attendant
    console which connects to the
    default position must use circuit
    2 to match default wiring from
    the maintenance panel. Other
    Superconsole 1000nlattendantconsoles may connect to any port
    on a Digital Line Card.
    Figure 5-25 Music, Paging, and Relay Connections
    Page 98 
    						
    							Shipping, Receiving, and Installation Information
    CHART 5-21
    INSTALL FLOPPY DISK DRIVE PN 9109-124-000Remove or install diskette in drive while power is on and LED is off.
    Remove power from the Bay before removing or installing a disk drive.
    StepAction
    Comments
    1.While wearing antistatic wrist strap, unpack and
    inspect new disk drive.
    2.Install drive into its slot in Bay 2, and secure itInstall second disk drive in Bay 1.
    with its latch and locking screw.
    3.If installing drive into an SX-200 weldedDisk drive 9109-124-000 requires
    cabinet, open rear door of cabinet.Disk Drive Adapter 9109-038-000.
    4.Remove ground wire and tie strap which holdsRefer to Figure 5-27.
    it, from side of shelf.
    5.Attach ground wire from adapter to frame of
    shelf using screw, external tooth washer, and
    nut.
    6.
    7.
    8.
    Plug adapter into DIN connector of floppy disk
    drive.
    Connect adapter ribbon cable to J35 and powerNote: Bay 1 adapter,
    cable to J39 on Control Shelf backplane. Refer9 109-037-000, connects to J37
    to Figure 5-27.
    and J33.
    Power up and initialize system.
    Page 99 
    						
    							SECTION MITL9109-094-200-NA
    LOCKING
    SCREW
    PN9109-124-000
    8536ElMFigure 5-26 Floppy Disk Drives
    Page 100 
    						
    							Shipping, Receiving, and Installation InformationPOWER /’CABLE
    RIBBON 
    -CABLEGROUND
    WIRE
    KAOlB6EOROFigure 5-27 Disk Drive Connections
    Page 101 
    						
    							SECTION MITL9109-094-200-NACHART 5-22
    UNPACK AND INSTALL PRINTED CIRCUIT CARDS
    WARNING
    ANY CONNECTION OF AN ONS LINE CARD, A DIGITAL LINE CARD, OR A COV LINE CARD, TO AN
    OFF PREMISE APPLICATION, AN OUT OF PLANT APPLICATION, OR TO ANY OTHER EXPOSED
    PLANT APPLICATION MAY RESULT IN A SAFETY HAZARD, AND/OR DEFECTIVE OPERATION,
    AND/OR EQUIPMENT DAMAGE.
    StepAction
    Comments
    CAUTION: Do not open or unpack any printedTHE ANTISTATIC WRIST STRAP
    circuit card cartons unless you are wearing
    MUST BE CONNECTED TO THEthe antistatic wrist strap.
    PABX CHASSIS, WHICH MUST BE
    CONNECTED TO AN APPROVED
    GROUND TO PROVIDE
    PROTECTION FROM STATIC
    DISCHARGES.
    1.
    2.Attach the antistatic wrist strap to your wrist,
    The system configuration and/or
    and handle printed circuit cards by their edgesthe Tip 
    & Ring Assignment forms
    only. Typical card packaging is shown in Figureidentify which card type goes into5-28.
    each slot.
    Unpack and inspect the Bay Power Supply (BPS) Return damaged or defective
    module.
    items, and report missing items
    according to local procedures.
    3.Insert the BPS into its slot in Bay 2, and tightenEnsure that the BPS I/O (ON/OFF)
    the thumbscrew at the upper front of the BPSswitch is in the 0 (OFF) position.
    to secure it to the cardfile.The first BPS must be in Bay 2; if
    any cards are to be installed inBay 1, a BPS must also be
    installed in Bay 1.
    4.At the rear of the Control cabinet, connect the
    Refer to Figure 4-3.
    AC line cord to the BPS plug.
    5.Unpack and inspect the Main Control Card andNote: Whenever a new release of
    the Decryption module, which is packaged with
    system software is received, the
    the system software diskette.system must be powered down,
    so that the new Decryption
    module can be installed on the
    MCC. Each software release has a
    unique Decryption module
    associated with it.
    6.Install a RAM module, a DX module, and aJumper and switch settings for
    Decryption module onto the MCC as defined in
    the MCC are factory set and doChart 5-23.
    not require changing. Refer to
    Figure 5-31.
    7.Install the MCC into its slot in the Control Shelf.Page 102 
    						
    							Shipping, Receiving, and Installation Information
    CHART 5-22 (CONT’D)
    UNPACK AND INSTALL PRINTED CIRCUIT CARDSStepActionComments
    8.480-PORT CONFIGURATIONInstall Digital Interface 
    Cards (DIC) in Bays 3, 4,
    and 5. Connect PCM cables to their associated
    DIC (each PCM cable connector is labeled to
    identify the DIC it connects with).
    336-PORT CONFIGURATION
    Install Bay Control Card (BCC), Bay Power
    Supply (BPS), and PCM cables to each digital
    Bay.
    456-PORT CONFIGURATION
    Install Bay Control Card (BCC) and Bay Power
    Supply (BPS) in Bay 3. Install Digital Interface
    Cards (DIC) in Bays 4 and 5. Connect PCM
    cables to their associated DIC (each PCM cable
    connector is labeled to identify the DIC it
    connects with).
    672 PORT
    In Bay 0, install Main Control Card (with
    modules), Switch Matrix Card (replaces DX
    module on MCC), two Floppy Disk Drives, Install
    Bay Control Card into each Peripheral bay.
    9.Unpack trunk cards (for Control and PeripheralRefer to Chart 5-26 through Chart
    bays), set switches or jumpers, and install into5-30.
    assigned slots.
    IO.Unpack, inspect, and install the remaining PCB
    cards according to the equipment assignment
    for this system.
    11.Retain some packing material for returning
    cards for repair. Discard the remainder
    according to local practice.
    Note:The following Digital Peripheral Cards are high power cards and are installed only in upper
    slots:
    - COV Line Card
    - OPS
    - DID
    - Universal
    The 
    LWGS, DLC and ONS cards are low power cards and can be installed in upper or lower
    slots.
    Page 103 
    						
    							SECTION MITL9109-094-200-NA
    7105EOROFigure 5-28 Printed Circuit Card Packaging
    Page 104 
    						
    All Mitel manuals Comments (0)

    Related Manuals for Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual