Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

							SECTION MITL9109-094-320-NACHART 3-3 (CONT’D)
TESTING LINE LOCKOUT ALARM
StepActionVerify
14While a lockout alarm isAll other consoles stop their long-short-long cadence and
active, exit from aresume any other cadence that may be active.
maimenance or CDE user
intetface at a consoleThe user at this donsole is prompted for 3 seconds to
(time-out or log out).press SHOW LOCKOUT after which the display is returned
to the application state and all other consoles start the
long-short-long cadence again at which time they can
show lockout alarms.
Notes:1. There can be 32 lockout alarms active at any one time; any further lockout alarm(s) will
only be recorded in the maintenance logs.
2. The long-short-long cadence will still ring if COS option 100 (Attendant Bell Off) is
enabled.3. The lockout alarm feature will operate with COS option 701 (No Dial Tone) enabled.
4. When a console is in restricted service, the long-short-long cadence will ring but the
user will not be able to read the alarm or turn the warbling off; the restricted access
code must be re-dialed before the user can press the APPLICATION hard key.
5. When there are no DTMF receivers available, the 45 second time period before the
lockout alarm occurs will be increased by the time waiting for an available receiver.
Page 46 
						

							System Test Procedures
4. STATION FEATURE TESTSGeneral
4.01This Part describes the station tests for the SX-200 DIGITAL
PABX. These tests are performed prior to the PABX being
brought into service in order 
tc verify the correct operation of the
stations and the features associated with them. Refer to Section
MITL9109-094-105-NA, Features Description, for details of the features
tested.
4.02Some of the features may be COS-restricted. Consequently, not
all features may be accessed from all stations. Refer to the
customer database (either by checking station COS levels at the Main-
tenance Terminal, or by referring to Section 
MITL9109-094-206-NA,Installation Forms) to determine which COS level is assigned to which
stations, and to determine which COS options are enabled within each
COS level.
4.03Satisfactory completion of the station feature tests confirms
that the stations have been installed and programmed correctly
according to the instructions provided in Section 
MITL9109-094-206-NA, Installation Forms, and Section 
MITL9109-094-210-NA, Customer
Data Entry, and that the features operate properly according to the
features descriptions in Section 
MITLSI 09-094-l 05-NA, Features De-
scription.
The tests performed in this Part cover the following features:
Abbreviated Dial
Broker’s Call
Call Forwarding (All Types)
Call Hold
Call Hold Retrieve (Local and Remote)
Callback Busy
Callback No-Answer
Camp-on
Conflict Dialing
Dial Call Pickup
Directed Call Pickup
Do Not Disturb
Extension Reset
Flash for Attendant
Hunt Groups
Line Lockout
Station Conference
Station-to-Station Call
Station Transfer.
Charts 4-l through 4-19 show the steps for testing station
features.
Page 47 
						

							SECTION MITL9109-094-320-NAStepActionCHART 4-l
ABBREVIATED DIAL
Verifv
1
2Station “A” lifts handset.Station “A” receives dial tone.
Station “A” dials the
Abbreviated Dial Access
Code and number.
3 1 Return handset.Test complete.
StepActionVerify
1
2Station “A” lifts handset.Dial tone is returned.
Station “A” dials station “B’
directory number.
3Station “B” lifts handset.
4Station “A” flashesStation “A” receives Interrupted Dial Tone. Station “B”
switchhook.receives silence (Consultation Hold).
5Station “A” dials station “C’
and establishes a
connection.
6Station “A” flashesStation “C” receives silence (Consultation Hold). Stations
switchhook.“A” and “B” are connected.
7
6
9
10Station “A” flashesStation “B” receives silence (Consultation Hold). Stations
switchhook.“A” and “C” are connected.
Station “A” replaces
handset.Station “A” lifts handset.
Replace all handsets.Test completed. Dial tone is removed on the first dialed digit. Following
the last dialed digit, outpulsing may be heard (if the
selected number is external). 
Ringback or busy tone is
returned.
CHART 4-2
BROKER’S CALL
Station “B” rings. 
Ringback tone is heard at station “A”.
Station “B” stops ringing. 
Ringback tone removed from
station “A”. Stations “A” and “B” are connected.
As above, Steps 2 and 3, except for stations “A” and “C”.
Stations “B” and “C” are NOT connected together.
Station “C” receives silence, and goes to a locked-out
condition if handset is not replaced. Station “B” receives
ringback tone. Station “A” rings. Station “A” lifts handset.
Station “A” and “B” are connected.
Page 48 
						

							System Test Procedures
CHART 4-3
CALL FORWARDING (ALL TYPES)StepActionVerify
CALL FORWARDING 
- BUSY
Part 1- Testing activation of Call Forwarc’ing -. Busy
1Station “A” lifts handset.Dial Tone returned.
2Station “A” dials CallDial Tone removed on first digit of access code dialed.
Forwarding 
- Busy accessDial Tone returned after station “C” directory number has
code, followed by stationbeen entered. (Call Forwarding 
- Busy activated.)
“C” directory number, then
sets handset on-hook.
3Station “A” stays off-hook.Station “B” receives Ringback Tone. Station “C” rings.
Station “B” dials station “A”
directory number.
4Station “C” lifts handset.Station “C” stops ringing. Ringback Tone removed from
station “B”. Stations “B” and “C” are connected.
5All stations replacePart 1 completed.
handsets.Part 2 
- Testing deactivation of Call Forwarding - Busy
1Station “A” lifts handset,Dial tone removed on first digit of access code dialed.
dials any Call Forwarding(Call Forwarding deactivated.)
access code and goes
on-hook.
2Station “A” lifts handset.
Station “A” receives Dial Tone. Station “B” receives Busy
Station “B” dials station “A” Tone.
directory number.
3Replace all handsets.Test completed.
Page 
49 
						

							SECTION MlTL9-7 09-094-320-NACHART 4-3 (CONT’D)
CALL FORWARDING (ALL TYPES)
StepActionVerify
CALL FORWARDING 
- NO ANSWER
Part 1 -Testing activation of Call Forwarding - No Answer
1Station “A” lifts handset.Dial Tone returned.
2Station “A” dials CallDial Tone removed on first digit of access code dialed.
Forwarding
- no AnswerDial Tone returned after last digit of station “C” directory
Access Code, followed bynumber. (Call Forwarding 
- No Answer activated.)
station “C” directory
number, then sets handset
on-hook.
3Station “B” dials station “A” Station “B” receives Ringback Tone. Station “A” rings for
directory number.two ringing cycles. Station “A” stops ringing and station
“C” rings.
4Station “C” goes off-hook.Station “C” stops ringing and Ringback Tone is removed
from station “B”. Stations “B” and “C” are connected
together.
5Set handsets on-hook.Part 1 completed.
Part 2 
- Testing deactivation of Call Forwarding - No Answer
1Station “A” lifts handsetDial Tone removed after first digit of access code dialed.
and dials any Call(Call Forwarding 
-No Answer deactivated.)
Forwarding Access Code
and hangs up.
2Station “B” dials station “A” Station “A” rings; station “B” receives Ringback Tone.
directory number. Allow
station “A” to ring for more
than two ringing cycles.
3Station “A” goes off-hook.Station “A” stops ringing; Ringback Tone removed from
station “B”. Stations “A” and “B” are connected together.
4Set handsets on-hook.Test completed.
Page 50 
						

							System Test Procedures
CHART 4-3 (CONT’D)
CALL FORWARDING (ALL TYPES)StepActionVerify
CALL FORWARDING 
- BUSY/NO ANSWER
Part 1 
-Testing activation of Call Forwarding - Busy/No Answer
1Station “A” lifts handset.Dial Tone returned.
2Station “A” dials CallDial Tone removed on first digit of access code dialed.
Forwarding 
- Busy/NoDial Tone returned after last digit of Station “C” directory
Answer access code,number. (Call Forwarding 
-Busy/No Answer activated.)
followed by Station “C”
directory number, and
remains off-hook.
3Station “B” dials Station “A” Station “B” receives Ringback Tone. Station “C” rings.
directory number.
4
Station “C” lifts handset.Stations “B” and “C” are connected.
5All stations replaceStation “B” receives Ringback Tone. Station “A” rings
handsets. Station “B” dialstwice, then stops ringing. Station “C” rings.
Station “A”.
6Station “C” lifts handset.Stations “B” and “C” are connected.
7Replace handsets.Part 1 completed.Part 2 
- Testing deactivation of Call Forwarding - Busy/No Answer
1Station “A” lifts handsetDial Tone removed after first digit of access code dialed.
and dials any Call(Call Forwarding 
-Busy/No Answer deactivated.)
Forwarding access code,
then hangs up.
2Station “B” dials StationStation “A” rings. Station “B” receives Ringback Tone.“A”. Allow Station “A” to
Station “C” does not ring (call not forwarded to Stationring for more than two
T’).
ringing cycles.
3Station “B” goes on-hook.Station “A” stops ringing.
4
Station “A” lifts handset,Station “A” receives Dial Tone.
and Station “B” dials
Station “B” receives Busy Tone.
Station “A”.
5Replace all handsets.Test completed.
Page 51 
						

							SECTION MITL9109-094-320-NACHART 4-3 (CONT’D)
CALL FORWARDING (ALL TYPES)
StepActionVerify
CALL FORWARDING - FOLLOW ME
Part 1
- Testing activation of Call Forwarding - Follow Me
1Station “A” lifts handset.Dial Tone returned.
2Station “A” dials CallDial Tone removed on first digit of access code dialed.
Forwarding 
- Follow MeDial Tone returned after station “C” directory number has
Access Code, followed bybeen dialed. (Call Forwarding 
- Follow Me activated.)
station “C” directory
number, then sets handset
on-hook.
3Station “B” lifts handset.Dial Tone returned.
4Station “B” dials station “A” Station “B” receives Ringback Tone. Station “C” rings.
directory number.
5Station “C” goes off-hook.Station “C” stops ringing. Ringback Tone removed from
station “B”. Stations “B” and “C” are connected together.
6Set handsets on-hook.Part 1 completed.
Part 2 
- Testing deactivation of Call Forwarding - Follow Me
1Station “A” lifts handset.Interrupted Dial Tone returned.
2Station “A” dials any CallDial Tone removed on first digit of access code dialed.
Forwarding Access Code,
then sets handset on-hook.
3Station “B” dials station “A” Station “A” rings. Station “B” receives Ringback Tone.
directory number andWhen station “A” lifts handset, stations “A” and “B” are
Station “A” lifts handset.connected together.
4Set handsets on-hook.Test completed.
Page 52 
						

							System Test Procedures
CHART 4-3 (CONT’D)
CALL FORWARDING (ALL TYPES)StepActionVerify
CALL FORWARDING 
- I’M HERE
Par,: 1- Testing activation of Call Forwarding - I’m Here
1Station “B” lifts handset.Dial Tone returned.
2Station “B” dials CallDial Tone removed on first digit of access code dialed.
Forwarding 
- I’m HereDial Tone returned after station “A” directory number
Access Code followed bydialed. (Call Forwarding 
- I’m Here activated.)
station “A” directory
number, then sets handset
on-hook.
3Station “C” lifts handsetStation “C” receives Ringback Tone. Station “B” rings.
and dials station “A”
directory number.
4Station “B” lifts handset.Station “B” stops ringing; Ringback Tone removed from
station “C”. Stations “B” and “C” are connected together.
5Set handsets on-hook.Part 1 completed.
Part 2 
- Testing deactivation of Call Forwarding - I’m Here
1Station “A” lifts handset.Interrupted Dial Tone returned.
2Station “A” dials any CallDial Tone removed on first digit of access code dialed.
Forwarding Access Code,(Call Forwarding 
-I’m Here deactivated.)
then sets handset on-hook.
3Station “C” lifts handsetStation “C” receives Ringback Tone; station “A” rings.
and dials station “A”
directory number.
4Station “A” lifts handset.Station “C” and station “A” are connected together.
5Set handsets on-hook.Test completed.
Page 53 
						

							SECTION MITL9109-094-320-NACHART 4-3 (CONT’D)
CALL FORWARDING (ALL TYPES)
StepActionVerify
CALL FORWARDING - EXTERNAL
Part 1
- Testing activation of Call Forwarding - External
1At Attendant Console,Refer to Section MITL9109-094-315-NA, Attendant
program a number external Console Description, for information regardingto the PABX as an
programming of Abbreviated Dialing numbers at the
Abbreviated DialingAttendant Console.
number.
2Station “A” lifts handset.Dial Tone returned.
3Station “A” dials a CallDial Tone removed on first digit of access code dialed.
Forwarding Access Code,Dial Tone returns after last digit of Abbreviated Dialing
followed by Abbreviatedentry number.
Dialing access code and
entry number.
4Station “A” sets handset
on-hook.
5Station “A” remains
on-hook if Call Forwarding
- No Answer, Call
Forwarding - Busy/No
Answer, or Call Forwarding
- Follow Me selected.
Station “A” establishes acall to station 
“C“ if Call
Forwarding - Busy
selected.
6Station “B” dials station “A” Station “B” receives Ringback Tone. Station “B” is routed
directory number.to external number. External number rings. Station “B”
receives external call 
ringback (or Busy Tone, if external
number is off-hook).
7External line goes off-hook. Station “B” and external number are connected together.
8External line and station “B” Part 1 completed. Go to Part 2.
set handsets on-hook.Page 54 
						

							System Test Procedures
CHART 4-3 (CONT’D)
CALL FORWARDING (ALL TYPES)StepActionVerify
CALL FORWARDING 
- EXTERNAL
Part 2 
-Testing Deactivation of Call Forwarding - External
1Station “A” lifts handset.Dial Tone returned.
2Station “A” dials any callDial Tone removed on first digit of access code dialed.
Forwarding Access Code,(Call Forwarding deactivated.)
then sets handset on-hook.
3Station “B” lifts handsetStation “A” rings. Station “B” receives Ringback Tone.
then dials station “A”
directory number.
4Station “A” lifts handset.Station “A” and station “B” are connected together.
5Set handsets on-hook.Test completed.
Page 55