Home > Mitel > Communications System > Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 55 Mitel manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 618
    							Customer Data Entry (CDE)Dataset. Because the DATASET 1102 is a dual DATASET, a second line
    appears for subcircuit 2 of the port.
    3-DSI 102 CCTP:This softkey appears after the DATA DEV TYPE
    softkey has been pressed on the second line of a port assigned as a
    DATASET 1102. It is the only softkey available in this situation. Press-
    ing the DS1102 CCT2 
    softkey assigns the device type for subcircuit 2
    of the port as an Asynchronous Rack Mount 
    Dataset.
    4-DSllOl: This softkey appears after the DATA DEV TYPE softkey has
    been pressed. Pressing this 
    softkey assigns the device type as a data
    cartridge.
    7-DS2102: This 
    softkey appears after the DATA DEV TYPE softkey has
    been pressed. Pressing this 
    softkey assigns the device type as an
    Asynchronous/Synchronous Rack Mount 
    DATASET.8-DS2103: This 
    softkey appears after the DATA DEV TYPE softkey has
    been pressed. Pressing this 
    softkey assigns the device type as an
    Asynchronous/Synchronous Rack Mount 
    DATASET.
    9-DSCONS: This softkey appears after the DATA DEV TYPE softkeyhas been pressed. Pressing this 
    softkey assigns the device type as a
    Mk 2 Console printer port.
    P-FIND EXT: Pressing the FIND EXT 
    softkey displays the ENTER EX-
    TENSION NUM prompt. When a valid extension number of a 
    DATASETis entered, its physical location is displayed on the command line.
    3-FIND AVL:Pressing this 
    softkey prompts the user to enter an
    extension number. When a valid extension number of an associated
    voice set is entered, and the ENTER 
    softkey is pressed, the physical
    location of the 
    DATASET which is associated with the selected voice
    set is displayed on the command line.
    5-RANGE: This softkey facilitates block programming of data devices.
    Pressing this 
    softkey displays FROM BAY; SLOT: and CIRCUIT: TO BAY:
    SLOT: CIRCUIT: prompts on the command line. The range of devices is
    then specified by entering valid bay, slot and circuit numbers for the
    first and last devices. The entry is completed by pressing the ENTER
    softkey. When the extension number for the first device is entered, the
    system automatically assigns incremented extension numbers, the
    same COS, COR, CDN, and DTE for each device in the block. A dual
    circuit 
    DATASET cannot be included in range programming.
    6-QUIT: Pressing this 
    softkey returns the display to the level before
    DATASET DEV TYPE was selected.
    7-BAY/SLT/CCT: When this softkey is pressed the command line
    displays: BAY: SLOT: CIRCUIT: prompts. Once the location is specified,
    and the 
    softkey ENTER is pressed, the command line updates with
    information about the device and the cursor moves to the 
    TYP field. If
    an invalid number is entered the system inhibits subsequent cursor
    movement.
    Page 69 
    						
    							SECTION MITL9109-094~Zl O-NA8-DELETE: This 
    softkey appears when the cursor is positioned at data
    on the command line. Pressing the DELETE 
    softkey removes the entry
    from the form. The deletion is completed by pressing the 
    softkey:
    ENTER.O-DELETE FIELD: This 
    softkey appears when the cursor is positioned
    in the AVL or HOTLINE field, when a value has been already pro-
    grammed. Pressing the DELETE FIELD 
    softkey removes the value which
    is programmed in that field. The deletion is completed by pressing the
    ENTER softkey.O-ENTER: This 
    softkey appears after data has been modified. Pressing
    the ENTER 
    softkey commits each modification one at a time to the
    database.Page 70 
    						
    							Customer Data Entry (CDE)
    Form 13 - Trunk Circuit Descriptors
    4.60Trunk circuit descriptors are similar to Classes of Service. A
    trunk circuit descriptor specifies the hardware options for eachtype of Trunk Card. Refer to Table 4-23, Trunk Circuit Descriptors for
    the form layout. Trunk circuit descriptors are complemented by the
    switch settings on the SX-200 type Trunk Cards. Refer to the Trunk
    Card Switch Assignments Forms in Part Number 
    9109-094-206-NA,
    Installation Forms. There are 12 Trunk Card types and are as follows:4-Circuit CO6-Circuit DID
    6-Circuit COE&M Trunk4-Circuit 
    DISAE&M Trunk DISA6-Circuit 
    DISAE&M Trunk Module DISA2-Circuit DID/TIE2 Circuit TIE 
    DISA
    EM MOD 
    DISATl Trunk
    Each Trunk Card type has its own set of parameters as detailed in
    Table 4-25, Trunk Hardware Options. The system supports a maximum
    of 25 trunk circuit descriptors.TABLE 4-23
    FORM 13 
    - TRUNK CIRCUIT DESCRIPTORS
    CDE TERMINAL DISPLAY
    12:Ol AM 15-JAN-88alarm status = NO ALARM
    DESCR I PTORTRLhlK TYPENlblBER OF TRKS ASSIGNEDcoMlENTs
    014-CIRCUIT CO0
    024-CIRCUIT CO0
    xi4-CIRCUIT CO06-CIRCUIT Co4
    056-CIRCUIT co3
    x;2-CCT DID/TIE04-CIRCUIT DISA
    xi2-CCT DID/TIEx2-CCT DID/TIE0
    :c:2-CCT DID/TIE04-CIRCUIT DISA124-CIRCUIT DISA8
    014-CIRCUIT 
    CD0l-6 
    CZT CO2-6 CCT DISA3-E&M MOWLE4-6 CCT DID5-** MORE **
    B-QUIT7-DESC NWlBER8-SEL. OPTION9-EM MCD DISAO-ATTENDANT CONSOLE DISPLAY
    DESCR I PTORTRUUK TYPENWIBER OF TRKS ASSIGNEDCCMENTS014-CIFWIT Co0F1>6 CCT coF2>8 CCT DISAF3>E&M MCIXJLEF4>6 CCT DID F5>F6XU I TF7>DESC NUdBERF8>SEL. OPTIONF9>FO>
    4.61Field Description
    DESCRIPTOR: This field lists the trunk circuit descriptors, numbers 
    01
    to 25.
    Page 71 
    						
    							SECTION MITLSI 09-094~Zl O-NATRUNK TYPE: This field lists one of eight trunk types for each trunk
    circuit descriptor. Note that the selected trunk type (the one that
    appears on the command line) is not displayed on the softkeys.
    NUMBER OF TRKS ASSIGNED: This field records the number of trunks
    which use each trunk circuit descriptor. The trunk circuit descriptor
    can be assigned a 
    new trunk type only if this field is zero. To clear the
    NUMBER OF TRKS ASSIGNED field, the trunks must first be deassigned.
    Refer to Table 4-27, Non-Dial-In Trunks and Table 4-28, Dial-In Trunks.
    When a trunk type is assigned to a trunk circuit descriptor, the system
    prohibits any changes by clearing those 
    softkeys that can alter the
    trunk types.
    COMMENTS: This field is reserved for additional data (a maximum of
    20 characters). It is stored by the system but not used.
    4.62 Commands
    l-6 CCT CO: Pressing this 
    softkey specifies the selected trunk circuit
    descriptor as a CO Trunk type. Pressing the ENTER 
    softkey completes
    the selection and the TYPE field displays the 6-CIRCUIT CO prompt.
    1-4 CCT CO: This 
    softkey appears when the MORE softkey has been
    pressed. Pressing this 
    softkey assigns the CO Trunk type to the se-
    lected trunk circuit descriptor. Pressing the ENTER 
    softkey completes
    the selection and the TYPE field displays the 4-CIRCUIT CO prompt.
    l-T1 LS/GS: This softkey appears when the MORE softkey has been
    pressed for the second time. Pressing this 
    softkey defines the selected
    trunk circuit descriptor as a 
    Tl Trunk simulating an LS/GS Trunk.
    l-T1 CO DISA: This softkey appears when the MORE softkey has been
    pressed for the third time. Pressing this 
    softkey defines the selected
    trunk circuit descriptor as a 
    T’l Trunk simulating a CO DISA Trunk.
    2-6 CCT DISA: Pressing this 
    softkey assigns the DISA Trunk type to
    the selected trunk circuit descriptor. Pressing the ENTER 
    softkey com-
    pletes the selection and the TYPE field displays the 6-CIRCUIT 
    DISAprompt.
    2-4 CCT 
    DISA: This softkey appears when the MORE softkey has been
    pressed. Pressing this 
    softkey selects the DISA Trunk type for that
    trunk circuit descriptor. Pressing the ENTER 
    softkey completes the
    selection and the TYPE field displays the 4-CIRCUIT 
    DISA prompt.
    2-Tl E&M: This soltkey appears when the MORE softkey has been
    pressed for the second time. Pressing this 
    softkey defines the selected
    trunk circuit descriptor as a 
    Tl Trunk simulating an E&M Trunk.
    2-Tl E&M DISA: This softkey appears when the MORE softkey has
    been pressed for the second time. Pressing this 
    softkey defines the
    selected trunk circuit descriptor as a 
    Tl Trunk simulating an E&M DISA
    Trunk.Page 72 
    						
    							Customer Data Entry (CDE)
    3-E&M MODULE: Pressing this softkey programs the selected trunk
    circuit descriptor as an E&M Trunk Module. Pressing the ENTER 
    softkeycompletes the selection and the TYPE field displays the E&M MODULE
    prompt.
    3-E&M TRUNK: This 
    softkey appears when the MORE softkey has
    been pressed. Pressing this 
    softkey programs the selected trunk circuit
    descriptor as an E&M Trunk Card. Pressing the ENTER 
    softkey com-
    pletes the selection and the TYPE field displays the E&M CARD prompt.
    3-Tl DID/TIE: This softkey appears wh.en the MORE softkey has been
    pressed for the second time. Pressing this 
    softkey defines the selected
    trunk circuit descriptor as a 
    Tl Trunk simulating a DID/TIE Trunk.
    3-Tl TIE DISA: This softkey appears when the MORE softkey has been
    pressed for the third time. Pressing this 
    softkey defines the selected
    trunk circuit descriptor as a 
    Tl Trunk simulating a TIE/DISA Trunk.
    4-6 CCT DID:Pressing this 
    softkey programs the selected trunk
    circuit descriptor as a DID Trunk. Pressing the ENTER 
    softkey com-
    pletes the selection and the TYPE field displays the 6 CCT DID prompt.
    4-DID/TIE: This 
    softkey appears when the MORE softkey has been
    pressed. Pressing this 
    softkey specifies the selected trunk circuit de-
    scriptor as a DID/Tie Trunk. Pressing the ENTER 
    softkey completes the
    selection and the TYPE field displays the 2-CCT DID/TIE prompt.
    5-** MORE **: This softkey presents mbre trunk type selections, each
    time it is pressed until it returns the 
    softkeys to their original format.
    (Refer to Table 4-23, Trunk Circuit Descriptors and Figure 4-13, More
    Trunk Types). Note that the current selected trunk type 
    softkey is left
    blank.l-4 
    aT co2-4 CCT DISA3-E & M TRWK4-DID/TIE5-
    6-QUIT7-DESC 
    NlNBER8-SEL. O!JTlcN9-EM TRK DISAO-TIE DISA
    l-T1 LWGS2-Tl E&M3-Tl DID/TIE 4-5-
    B-QUIT‘I-DESC NLMBER8-SEL. OPTION 9-O-
    l-T1DISAB-QUIT2-3-4-
    7-DESC 
    MhlBER8-SEL. OPTION 9-Figure 4-13 More Trunk Types5-O-6-QUIT: Pressing the QUIT 
    softkey when editing this form returns the
    display to the level before the field was modified. The change is not
    saved. At all other times, pressing this 
    softkey exits Form 13 and
    returns the display to the level where the forms are selected.
    B-CANCEL: This 
    softkey appears after a programming error has oc-Page 73 
    						
    							SECTION MITLSI 09-094-ZIO-NA
    curred. Pressing the CANCEL softkey returns the display to the level
    where the programming error occurred. The CANCEL 
    softkey appears
    with an error message.
    7-DESC NUM:Pressing this 
    softkey displays ENTER DESC NUM:
    prompt. This 
    soltkey selects a trunk circuit descriptor number. The
    selection is completed by entering a valid number (1 to 25).
    8-SEL. OPTIONS: Pressing the SEL. OPTIONS 
    softkey displays a new
    form. This form displays the options (parameters) associated with the
    trunk type that is assigned to that trunk circuit descriptor. Refer to
    Table 4-24, Trunk Circuit Descriptor Options.
    9-EM TRK DISA: This softkey appears when the MORE softkey has
    been pressed. Pressing this 
    softkey commits the (E&M) analogue trunk
    as a 
    DISA trunk.
    9-EM MOD DISA: Pressing this softkey programs the selected trunk
    circuit descriptor as an EM MOD DISA.
    O-REVIEW: Pressing the REVIEW 
    softkey displays a new form (refer to
    Table 4-26, Review List for Form 13). This form displays a list of trunks
    that use the selected trunk circuit descriptor. Note that this 
    softkeyappears only if “NUMBER OF TRKS ASSIGNED” on command line is
    greater than zero.
    O-ENTER: This 
    softkey appears only after data for an entry has been
    modified. Pressing the ENTER 
    softkey commits each modification one
    at a time to the database.
    O-TIE DISA: This 
    softkey appears when the MORE softkey has been
    pressed. Pressing this 
    softkey commits the DID/TIE (analog) trunk as a
    DISA trunk.
    Page 74 
    						
    							Customer Data Entry (CDE)
    Options for Trunk Circuit Descriptors
    4.63 This form appears only when the SEL. OPTIONS softkey is
    pressed (refer to Table 4-23, Trunk Circuit Descriptors). This
    form displays the options (parameters) associated with each trunk type
    assigned to each trunk circuit descriptor. Refer to Table 4-24, Trunk
    Circuit Descriptor Options.
    TABLE 4-24
    TRUNK CIRCUIT DESCRIPTOR OPTIONS FOR FORM 13
    CDE TERMINAL DISPLAY
    4:26 PM 15-JAN-88alarm status = NO ALARM
    I4CCTCOTRU’JK: 2I OPTION NAME [SUPERVISION PARAMETER]STATUS
    Far-end gives answer supervision
    Inhibit automatic supervision
    LizNo seize alarmYESNo release alarmYESToll office
    No
    Is this a CO
    YES
    DTMF
    YESImpedance
    COMPLEXDictation TrunkNOFar-end gives answer supervision
    No
    1 -YES2-
    3-4-5-
    6-QUIT7-
    8-9-O-ATTENDANT CONSOLE DISPLAY
    [ 4CCTCOTRWJK:2 1 OPTION NAME [SUPERVISION PARAMETER]
    Far-end gives answer supervision
    Fl>YESF2>F3>F4>F5>F6>oU ITF7>F8>F9>FO>STATUS
    NO4.64Field Description.: The header line displays the trunk type, the
    trunk circuit descriptor number and the type of parameter under
    observation. The parameter types are: Supervision, Transmission, In-
    coming, Outgoing and In/Out Going. Refer to Table 4-25, Trunk Hard-
    ware Options for a complete list of these options.
    STATUS: This field lists the option selected for each parameter.
    4.65 Commands
    l-YES, NO, COMPLEX, 600 OHM, 
    60/40, IMMEDIATE: This softkeytoggles the status of the parameters.
    2-30/20, WINK: This softkey toggles the status of the parameters.
    3-66/33, DELAY: This softkey toggles the status of the parameters.
    4-DELAY INTEG: This 
    softkey toggles the status of the parameters.
    6-QUIT: Pressing the QUIT 
    softkey when editing this form returns the
    Page 75 
    						
    							SECTION MITL9109-094-210-NAdisplay to the level before the field was modified. The change is not
    saved. The following warning prompt appears on the command line:
    DATA HAS BEEN CHANGED BUT NOT YET SAVED IN DATABASE --
    “ENTER” TO SAVE. At all other times, pressing this softkey returns the
    display to the point where the SEL. OPTION 
    softkey was pressed.6-CANCEL: This 
    softkey appears after a programming error has oc-
    curred. Pressing the CANCEL 
    softkey returns the display to the level
    where the programming error was made. The CANCEL softkey appears
    with an error message.O-ENTER: This 
    softkey appears only after data for an entry has been
    modified. Pressing the ENTER 
    softkey commits each modification one
    at a time to the database. After all changes have been completed, theuser must press the ENTER 
    softkey again to commit the form to the
    database.TABLE 4-25
    TRUNK HARDWARE OPTIONS
    4-CIRCUIT 
    Co TRWJK and 4-CIRCUIT DISAReverse to Idle
    Far-End Gives Answer Supervision
    Inhibit Automatic Supervision
    No Seize Alarm
    No Release Alarm
    Toll Office
    Is this a CC
    DTMFImpedance (600 Ohms or Complex)
    Dictation Trunk
    6-CIRCUIT 
    CC TRUVK and 6-CIRCUIT DISAReverse to Idle
    Far-End Gives Answer Supervision
    Inhibit Automatic Supervision
    No Seize Alarm
    No Release Alarm
    Toll Office
    Is this a CC
    DThlFImpedance (600 Ohms or Complex)
    Post Call Metering 
    (0 -+ 15 seconds)
    Calling Party Disconnect Timer (I * 12 minutes)
    Dictation Trunk
    Ignore Remote Disconnect
    Disconnect Timer (100 
    -) 9900 ms)(100 ms increments)
    Supervision Direction:Incoming Trunk Calls Also
    Guard Timer (0 
    + 3000 ms) (100 ms increments)
    Ring Cycle Timer (6 -+ IO seconds)
    Ignore Line Reversal During Seizure
    Ringing Expected
    Ringing 
    Debounce Timer (5 + 12 seconds)
    Seize Timer (IO -) 60 s) (IO s increments)
    Flash Timer (200 + 700 ms)(100 ms increments)
    Interdigit Timer (300 4 600 ms)(100 ms increments)
    Digit Outpulsing Ratio (60/40, 30/20, 66/33)Page 76 
    						
    							Customer Data Entry (CDE)
    TABLE 4-25 (CONT’D)TRUNK HARDWARE OPTIONS
    Type :E&M 
    M(WXILE and E&M MCDJLE DI SA
    Reverse to Idle
    Far-End Gives Answer Supervision
    Inhibit Automatic Supervision
    No Seize Alarm
    No Release Alarm
    Toll Office
    Is this a CC
    Dl%lFImpedance ** Use Module Dip Switches to Program ** (600 Ohms or (Complex)
    E Lead Invert
    M Lead Invert 
    ** required for type 5 operation **Disconnect Timer (150 4 300 msl(50 ms increments)
    Release Acknowledge Timer (2000 + 9900 ms)(100 ms inc)
    Guard Timer (200 -+ 1000 ms)(100 ms increments)
    Dictation Trunk
    Incoming Start Type 
    (Imned, Wink, Delay)Debounce Timer (20 -+ 150 ms)(IO ms increments)
    Wink Timer (150 + 300 ms) (50 ms increments)
    Outgoing Start Type (lamed,Wink, Delay or Delay Integ)Digit Outpulsing Ratio (60/40, 30/20, 66/33)Outpulse Delay Timer (100 -+ 2000 ms)(100 ms inc)Flash Timer (200 + 700 ms)(100 ms increments)
    Interdigit Timer (300 - 800 ms)(100 ms increments)
    Wait for Delay Timer (300 --) 5000 ms)(100 ms inc)
    Remote End is a Satellite
    Remote End is a Satellite with OPS Lines
    E&M TRUUK CARDReverse to Idle
    Far-End Gives Answer Supervision
    Inhibit Automatic Supervision
    No Seize Alarm
    No Release Alarm
    Toll Office
    Is this a CC
    DTMFImpedance (600 Ohms or Complex)
    Remote End is a Satellite
    Remote End is a Satellite with OPS Lines
    Dictation Trunk
    2-CCT DID/TIE and 2 CCT TIE DISAReverse to Idle
    Far-End Gives Answer Supervision
    Inhibit Automatic Supervision
    No Seize Alarm
    No Release Alarm
    Toll Office
    Is this a 
    CoDlIlFImpedance (600 Ohms or Complex)
    Remote End is a Satellite
    Remote End is a Satellite with OPS Lines
    6-CCT DID
    Reverse to Idle
    Far-End Gives Answer Supervision
    Inhibit Automatic Supervision
    Page 77 
    						
    							SECTION MITL9109-094-210-NATABLE 4-25 (CONT’D)
    TRUNK HARDWARE OPTIONS
    6-CCT DID (CCM’D)No Seize Alarm
    No Release Alarm
    Toll Office
    Is this a- CD
    DTMFImpedance (600 Ohms or Complex)
    Disconnect Timer (150 
    -) 300 ms)(50 ms increments)
    Release Acknowledge Timer (2000 -+ 9900 ms)(100 ms inc)
    Guard Timer (200 -+ 1000 ms)(100 ms increments)
    Start Type (Inmed)Debounce Timer (20 --) 150 ms) (10 ms increments)
    Wink Timer (150 --( 300 ms) (50 ms increments)
    Remote End is a Satellite
    Remote End is a Satellite with OPS Lines
    ‘1 E&l and Tl E&M DISAReverse to Idle
    Far-End Gives Answer Supervision
    Inhibit Automatic Supervision
    No Seize Alarm
    No Release Alarm
    Toll Office
    Is this a CD
    DTMFDisconnect Timer (150 --( 300 ms) (50 ms inc)Release Acknowledge Timer (2000 -+ 9900 ms) (100 ms inc)Guard Timer (200 + 1000) (100 ms inc)Incoming Start Type (Iraned. Wink or Delay)Debounce Timer (20 + 150 ms) (10 ms inc.)
    Wink Timer (150 -) 300 ms) (50 ms inc)Outgoing Start Type (Imned, Wink, Delay or Delay Integ)Digit Outpulsing Ratio (60140, 60/20, 66133)Outpulse.Delay Timer (100 + 2000 ms) (100 ms inc)Flash Timer (200 -+ 700 ms) (100 ms inc)Interdigit Timer (300 + 600 ms) (100 ms inc)Wait for Delay Timer (300 + 5000 ms) (100 ms inc)
    Remote end is a satellite
    Remote end is a 
    sate1 I i te with OPS Lines
    ‘1 DID/TIE and Tl TIE DISAFar-End Gives Answer Supervision
    Inhibit Automatic Supervision
    No Seize Alarm
    No Release Alarm
    Toll Office
    Is this a CD
    DTMFDisconnect Timer (150 -+ 300 ms) (50 ms inc)
    Release Acknowledge Timer (24 120 s)Guard Timer (200 + 1000) (100 ms inc)
    Start Type (Irmted, Wink or Delay1Debounce Timer (20 + 150 ms) (10 ms inc)
    Wink Timer (150 + 300 ms) (50 ms inc)
    Outgoing Start Type (Imned, Wink, Delay or Delay Integ)Digit Outpulsing Ratio (60140, 80/20, 66133)Outpulse Delay Timer (100 --) 2000 ms) (100 ms inc)
    Flash Timer (200 + 700 ms) (100 ms inc)
    Interdigit Timer (300 + 800 ms) (100 ms inc)Wait for Delay Timer (300 -( 5000 ms) (100 ms inc)
    Remote End is a Satellite
    Remote End is a Satellite With OPS Lines
    Page 78 
    						
    All Mitel manuals Comments (0)

    Related Manuals for Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual