Home > Mitel > Communications System > Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 55 Mitel manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 618
    							Customer Data Entry (CDErTABLE 5-l (CONT’D)
    PROGRAMMING ERROR MESSAGES
    Error Message
    comnent sNon-existent account code
    value has been entered.
    Mean i ngCDE Forms are not saved.
    During a search in Form 32, CDE Data Print,
    the entered Account Code does not exist.
    Select another Account Code.
    No 
    NCIN-DIAL-IN trunk cards are A card that supports Non-Dial-In Trunks must
    programnedbe defined in Form 01, System Configuration.
    No STATION or 
    SUPERSE-T cardsA card that supports Rotary Dial or DTMF sets
    are programnedor a card that supports SUPERSET telephones
    must be defined in Form 01, System
    Configuration.
    No trunks are assigned toThe trunk circuit descriptor number entered
    circuit descriptor number Xhas not been specified in Form 13, Trunk
    Circuit Descriptor.
    NUvlBER OF DIGITS TO ABSORBIn the M field of Form 15, Dial-In Trunks,
    must be in the range (0 - 8)the maximum quantity of digits allowed is 8.
    MUS Port access code XXXXXThe access code entered for the Music Source
    does not existFollowing a Recording is non-existant or
    illegal.
    Dption XX conflicts with thisThe selected option is mutually exclusive
    opt ion.with the option number shown.
    Option number XXX is out ofThe selected option number is out of range.
    range;must be between XXX and For CDS Options, the valid range is 100 to
    xxx908. For System Options, the valid range is 1
    to 52.
    Overflow Agent Groups must beThe selected overflow agent group is a
    un i queduplicate of an overflow already specified for
    this path,or it is the primary agent group
    for this ACD path.
    Recording access code XXXXXThe access code entered for a recording is
    does not existnon-existant or illegal. The code must be for
    a recording hunt group.
    The power rating of theThe power rating of the Universal Card is 10.
    LNIVERSAL CARD is exceeded.Therefore,the number of modules that can be
    installed on the Universal Card depends on the
    individual power rating of the modules. The
    Console Module has a power rating of 5, the
    Receiver/Relay Module has a power rating of 2,
    the Music on Hold/Pager Module has a power
    rating of 1 and the E&M Trunk Module has a
    power rating of 3.
    Previous transactionDue to the I/O failure, the last write
    encountered a permanent I/Oprocess did not occur. Exit CDE Mode, reset
    Page 
    189 
    						
    							SECTION MITL9109-094-210-NATABLE 5-1 (CONT’D)
    PROGRAMMING ERROR MESSAGES
    Error Message
    Meaning
    failure; data was not writtenthe system and re-enter CDE Mode.
    to disk
    Print Option out of range.In Form 32, Customer Data Print, there are
    Valid range is
    (1- 50).
    only 50 Print Option numbers. Select a new
    Print Option number.
    This printer specification has
    System already contains printer parameters.
    already been programned.
    Recording 
    1 Start Time must beThe values for these two i terns must be> = Delay For Ringbackadjusted as indicated.
    ROUTE LIST out of range.The selected Route List number is invalid.
    Valid range is (1 - 100)The range is 1 to 100. Refer to Form 24, ARS:
    Route Lists.
    RGUTE out of range. Valid
    range is (1 - 200)The selected Route number is invalid. The
    range is 1 to 200. Refer to Form 23, ARS:
    Route Definition.
    ROUTE PLAN out of range. Valid The selected Route Plan number is invalid.
    range is (1 - 501The range is 1 to 50. Refer to Form 25, ARS:
    Route Plans.
    RTE 
    PLN= X, DZ= X, TZ= X,
    The entered Route List number does not have a
    Field= ROUTE LIST: Error= entry corresponding entry in the START l-WR field.
    must be blankTherefore,
    the ROUTE LIST field must be
    cleared or a starting time must be specified
    in the START 
    KUR field. Refer to Form 25,’ ARS: Route Plans. _
    RTE PLN= X, DZ= X, TZ= X,The START HDUR field entry is less than or
    Field= START HOUR, Error =equal to the previous START l-KJUR field entry.
    Entry < = previous entryThe entries in the START HIUR field must be
    listed in ascending order. Refer to Form 25,
    ARS: Route Plans.
    RTE PLN= X, DZ= X, TZ= X,A blank entry in the START l-KlUR field
    Field= START HOUR, Error= Entry represents 24 hours. Therefore, the subsequent
    cannot be deletedentry in the START HCIUR field is less than or
    equal to the blank entry. Starting times must
    be listed in ascending order. Refer to Form
    25, ARS: Route Plans.
    Start time of a recording mustAdjust the start time as indicated.
    be < Interflow timeout
    Start time of a recording mustThe recording start times should be adjusted
    be < start time of the nextas indicated.
    recording
    Supervisor XXXXX does notA Supervisor with ID XXXXX, cannot be
    Page 190 
    						
    							Customer Data Entry (CDE)
    TABLE 5-l (CONT’D)
    PROGRAMMING ERROR MESSAGES
    Error MessageMeaning
    existdisplayed, as requested via the FIND SUPER
    key, because this access code has not been
    assigned to a supervisor.
    TENANT NUIBER is out of range.
    IThere are a maximum of 25 Tenant Groups.
    Valid is 1 to 25.-1The 
    TREK NWIBER XXX is
    already assigned
    The 
    TRUUK NUMBER XXX has not
    been assignedTrunk numbers can be assigned to only one
    trunk. Trunk numbers are assigned in Form 14,
    Non-Dial-In Trunks and Form 15, Dial-In
    Trunks.
    Entered trunk number does not correspond to a
    trunk. It must be defined in Form 14,
    Non-Dial-In Trunks or Form 15, Dial-In Trunks.
    The value X is outside valid
    IThe selected bay number is invalid.
    range for BAY (I - 5)is 1 to 5.
    The value XX is outside validThe selected circuit number is invalid.
    range for CIRCUIT 
    (I - XX)IThe value XX is outside valid
    range for CIRCUIT DESCRIPTORS
    (1 
    - 25)There are a maximum of 25 trunk circuit
    descriptors.
    The value XX is outside validThe selected 
    CDR Group number is out of
    range for CDR (1 - 25)range. The range is 1 to 25.
    The value XX is outside valid
    range for CDS 
    (1 - 50)The selected CDS number is out of range; the
    range is 1 to 50.
    The value XX is outside valid
    range
    for ENTRY 
    NLI+lBER (I - XX)In Form 18, Miscellaneous System Ports, there
    are only 38 Entry Numbers.
    The value X is outside validThe selected Hunt Group number is invalid
    range for 
    l-WIT GROUP (I - 50)The range is 1 to 50.
    The value XX is outside valid
    range for INTERCONNECT 
    NIJIBER(1 -xx)In Form 30, Device Interconnection Table,
    there are only 25 Interconnect Numbers.
    The value XX is outside the
    valid range for KEY 
    NUIBERS (2- 15)The selected 
    SUPERSET key number is
    invalid. Key numbers range from 2 to 15.
    SUPERSET key 1 is reserved for the Prime
    Line and cannot be programned in theSUPERSET Telephone Lines form.
    The value XX is outside valid
    IThe selected Pickup Group number is invalid;
    range for PICKUP GROUP (I - 50) the range is 1 to 50.IPage 191 
    						
    							SECTION MITLSI 09-094-210-NATABLE 5-l (CONT’D)
    PROGRAMMING ERROR MESSAGES
    Error Message
    Mean i ngThe value XX is outside theThe selected timer value is invalid. Refer to
    valid range for the selectedTable 4-25, Trunk Hardware Options for a list
    tirer optionof valid timer values.
    The value XX is outside validThe selected slot number is invalid.
    range for SLOT 
    (I - XX)The value XX is outside validIn Form 25, ARS Route Plans, the START HOUR
    range for START 
    WlJR (0 - 23)specifies the starting time for each time
    zone. The time is represented by two digits in
    24 hour format.
    The value XX is outside validSubcircuits 1 to 4 refer to the DTMF
    range for SUBCIRCUIT 
    (X - X)Receivers;they cannot be accessed. The only
    subcircuits that can be accessed are the
    relays on the Receiver/Relay Module. These are
    Subcircuits 5 and 6.
    The value XX is outside validThe selected Tenant Group number is invalid;
    range for TENANT 
    (1 - 25)the range is 1 to 25. Tenant Group numbers are
    used in the following forms:
    Form 05, Tenant Interconnection Table,
    Form 06, Tenant Night Switching Control,
    Form 07, Console Assignments,
    Form 09, Station/SUPERSET Telephones ,
    Form 12, Data Assignment,
    Form 14, Non-Dial-In Trunks,
    Form 15, Dial-In Trunks and
    Form 19, Call Rerouting Table.
    The value X is outside validThe selected Trunk Group number is invalid.
    range for 
    TRWK GROUP (1 - 50) The range is 1 to 50.
    The value XXX is outside valid Trunk numbers range from 1 to 200.
    range for 
    TRIJJK NLBIBERS (1 -200)
    TOTAL DIGITS EXPECTED must beIn Form 15, Dial-In Trunks, the N field
    in the range 
    (I - 9)(total digits expected) is restricted to
    digits 1 to 9.
    Total number of 
    SUPERSETThe power supply restricts the total number
    sets programed in Bayof SUPERSET telephones for the Control Cabinet
    3 cannot exceed 64to 64.
    Total number of 
    SUPERSETsets programned in Bays
    4 and 5 cannot exceed 64
    Total string is too long.
    Limit is 26 digitsThe power supply restricts the total number
    of SUPERSET telephones for the Peripheral
    Cabinet to 64.
    The total number of digits in the DIGITS TO
    BE ANALYZED field plus the digits in the
    LEADING DIGITS field cannot exceed 26. Refer
    to Form 26, ARS Digit Strings.
    Page 192 
    						
    							Customer Data Entry (CDE)
    TABLE 5-l (CONT’D)
    PROGRAMMING ERROR MESSAGES
    Error MessageMeaningTRUUK GROUP must be enteredTo complete the Route definition, the Trunk
    for a route to be defined
    Group number must be specified. Refer to Form
    23, ARS: Route Definition.
    TREK NWIBER XX does notOnly CD trunks can be assigned as DTS in the
    correspond to a CC trunkSUPERSET Telephone Lines form.
    TWK NWBER XXX is a memberThe selected trunk number is a member of the
    of TRUUK GROUP Xx.Trunk Group shown. A trunk number can be a
    member of only one Trunk Group at a time.
    Unable to delete 
    - A device is Circuits are assigned to the selected card in
    programned for thethat bay and slot. Cannot delete the card in
    Bay/Slot/Circuit 
    - XX/XX/XXthat slot until the devices are deassigned
    from the forms.
    Unable to locate extension
    XXXXX assigned to a PICKUPThe selected extension number is not assigned
    to any station or set. Refer to Form 09,
    GROUPStation/SLJPERSET Telephones.
    Unable to stop 
    CDE print. Try
    The Customer Data print process cannot be
    again later.halted. Try again later.
    Undefined access number or
    digit stringIn Form 31, System Abbreviated Dial Entry,
    either the Index Number or the Digit String is
    blank. Specify the required Index Number or
    Digit String.
    Unmatched Account code length;The length of the entered Account Code does
    system option account codenot match the Account Code Length specified in
    length enabled.System Option 49. (See Form 04, System
    Options/System Timers). Enter a new Account
    Code or change the Account Code Length option.
    Jpdate of database failed.
    The changes to the database were not stored
    properly on the diskette(s). Ensure proper
    positioning of the diskette(s) in the
    drive(s).
    Valid CDS range must beBefore a print operation can occur, a valid
    entered before CDS print isCDS range must be entered 
    (1 to 50). Refer to
    initiatedForm 03, COS Define.
    Valid TRK CCT 
    DESC range mustThis error occurs in Form 32, CDE Data Print.
    be entered before print isThe valid Trunk Circuit Descriptor range is 1
    initiatedto 25.
    The value XX is outside valid
    range for ACD Agent GroupThe ACD Group number entered is out of range.
    (I-50)
    The value 0 is outside validThe selected ACD Path or Priority is invalid.
    Page 193 
    						
    							SECTION MITLSI 09-094-210-NA
    H
    :
    vidPTABLE 5-1 (CONT’D)
    PROGRAMMING ERROR MESSAGES
    Error Message
    ‘ange (I-99)
    Mean i ng
    lerified account codes systemIn Form 33, Account Code Entry, the Accountoption must be enabled first.Code can only be modified if System Option 05,
    Verified Account Codes is enabled. Refer to
    Form 04, System Options/System Timers.
    iarning: This path will beThe user attempted to QUIT this form with
    leleted unless 1st two status“Access Code for This ACD Path” or “Primary
    ines are assignedACD Agent Group” field blank. A path is
    meaningless without these two pieces of
    information. The user is now provided with twc
    keys: 
    GUIT, which quits the form and deletes
    this path, and BACK TO FORM (softkey 0). which
    returns the user to the form.
    farning: Reassigning agentThe inserted ID is one that is already
    :rom group XX. CONFIRM orprogramned in group XX. This agent will be:ANCELreassigned now to the current ACD Group. Press
    either the CONFIRM or CANCEL softkey.farning:
    Ret X info will beThe user attempted to QUIT the form while
    leleted unless Start Time &only one of the indicated status fields forrecess Code assignedRecording X was assigned. Recording info is
    meaningless without both these pieces of info.
    The user is provided with two keys now: QUIT,
    which quits the form and deletes all entered
    info about Recording X, and BACK TO FORM
    (softkey 0) which returns the user to the
    form.
    Page 194 
    						
    							MITEL STANDARD PRACTICESECTION MITL9109-094~320-NAIssue 1, April 1988
    SX-200” DIGITAL
    PRIVATE AUTOMATIC BRANCH EXCHANGE (PABX)
    SYSTEM TEST PROCEDURES
    @Copyright 1988, MITEL Corporation. All rights reserved.
    T”Trademark of MITEL Corporation
    ‘Registered Trademark of MITEL Corporation 
    						
    							SECTION MITL9109-094-320-NA
    NOTICEThe information contained in this document is believed to be accurate in all respects but is
    not warranted by 
    Mite1 Corporation (MITEL). The information is subject to change without
    notice and should not be construed in any way as a commitment by 
    Mite1 or any of its
    affiliates or subsidiaries. 
    Mite1 and its affiliates and subsidiaries assume no responsibility
    for any errors or omissions in this document. Revisions of this document or new editions of
    it may be issued to incorporate such changes. 
    						
    All Mitel manuals Comments (0)

    Related Manuals for Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual