Home > Mitel > Communications System > Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 55 Mitel manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 618
    Add page 91 to Favourites
    image text
    Enable zoom 
    							Shipping, Receiving, and Installation Information
TABLE 5-l
MAINTENANCE PANEL RS-232 CONNECTOR PIN ASSIGNMENTSDTEDCERS-232RS-232data terminal equipment data communication equipment
pinsignal[local (dte) port]
[remote (dce) port]
2TRANSMIT DATAfrom terminalto modem
3RECEIVE DATAto terminalfrom modem
4REQUEST TO SENDfrom terminalto modem
5CLEAR TO SENDto terminal
6DATA SET READYto terminal
7SIGNAL GROUND
8CARRIER DETECTto terminalfrom modem
20DATA TERMINAL READYfrom terminalto modem
Notes:Remote (DCE) connector may be on the Maintenance Panel or on the Power Distribution Panel at
rear of cabinet.
On the Universal Cabinet, RS-232 and PRINTER port connectors are wired as follows:
J5 DTE pins 6, 8, and 20 are tied together.
DCE pin 5 and DTE pin 20 are tied together.
J8 PRINTER pins 6, 8, and 20 are tied together.
Page 85
    Add page 92 to Favourites
    image text
    Enable zoom 
    							SECTION MITLSI 09-094-200-NATERMINAL
REMOTE 
- DEDICATED, PUBLIC NETWORK
REMOTELV LOCATED
TERMINAL
REMOTE 
- DIAL-UP
TO DPABX VIA
CENTRAL OFFICE
~0 PAIRCROSSCONNECTFOR AUTO-ANSWER
MODEM.REMOTELV LOCATED
TERMINAL
NOTE: The Auto-Answer MODEM is
permanently connected to 
onelocal station circuit (extension).
7707ElRFigure 5-18 Maintenance Terminal Connections 
- SX-200 Cabinet
Page 86
    Add page 93 to Favourites
    image text
    Enable zoom 
    							Shipping, Receiving, and Installation Information
REMOTE - DEDICATED, PUBLIC NETWORK
REMOTELY LOCATED
TERMINAL
REMOTE 
- DIAL-UP
REMOTELY LOCATED
TERMINAL
CONNECTAUTO-ANSWER
MODEM.
NOTE: The Auto-Answer MODEM is
permanently connected to one
local station circuit (extension).TO DPABX VIA
CENTRAL OFFICE
MODEM
KAOl97EOROFigure 5-19 Maintenance Terminal Connections 
- SX-200 Universal Cabinet
Page 87
    Add page 94 to Favourites
    image text
    Enable zoom 
    							CHART 5-18
INSTALL ATTENDANT CONSOLE-ISECTION 
MITL9109-094-200-NAStepActionComments
1.Unpack console and place it in position atRefer to Figure 5-20.
Attendant workstation.
2.Connect headset (or handset) to its cord, andThe two jacks are in parallel;
plug cord into jack at side of console.either may be used.
3.Plug the console modular cord into the jack atJack is marked LINE PORT.
the back of the console and into its assigned
modular telephone jack.
4.At the distribution frame, cross connect theFor wiring information for the
cable from the modular jack to the PABX; to the consoles and the console modular
console module of the Universal card. Refer tojacks, refer to Figure 5-25.
Figure 5-21.
The LCD Console connects to a Console Module on the Universal Card using a four-wire connec-
tion.
The Console jack on the Maintenance panel must be connected to its default position (Bay 2, Slot 3,
Position 1 of a COMBO backplane or Bay 1 Slot 5 of a 672-port Control Cabinet), to allow access to
the default connected to this jack, during installation and initial Customer Data Entry. The card slot
must contain a Universal Card with a Console module in position 1.
The maximum loop length from the cabinet to the console is 300 m (1000 ft) using 26-AWG wire.Notes:
Page 88
    Add page 95 to Favourites
    image text
    Enable zoom 
    							Shipping, Receiving, and installation Information
I,PRE-FORMED/ FOAM
PACKAGING
SHIPPING
CARTON
7959EOROFigure 5-20 Unpacking Attendant Console
Page 89
    Add page 96 to Favourites
    image text
    Enable zoom 
    							SECTION MITL9109-094-200-NA
DPABX
CROSS
- y!I’IyMODULAR
JACK
25 PAIR
CONNECTORIZEDCABLE
xQUAD
STATION
WIRE
CONSOLEMODULAR
CORDCONSOLE MODULE
ON UNIVERSAL
CARDNOTE:USE ONLY 
MITEL CABLE
P/N 559900007 FOR THE
CONSOLE MODULAR CORD.
770BEZRlFigure 5-21 Console Installation
Page 90
    Add page 97 to Favourites
    image text
    Enable zoom 
    							Shipping, Receiving, and Installation Information
CHART 5-19
INSTALL SUPERCONSOLE 1000TM ATTENDANT CONSOLE
StepActionComments
1.Unpack console and place it in position at
Attendant workstation.
2.
3.C 
)nnect handset (or headset) to its cord, andThe two jacks are in parallel;
plug cord into jack at side of console.either may be used.
Plug the console modular cord into the LINE
PORT jack at the back of the console and into
its assigned modular telephone jack.
4.At the distribution frame, cross connect the
cable from the modular jack to its assigned
Digital Line Card in the PABX. Refer to Figure
5-22.For console modular jack wiring
information, refer to Figure 5-25.
Notes:The Superconsole 1000 attendant console uses a two-wire connection to connect to one circuit on
a Digital Line Card (tip to tip and ring to ring).
The Console jack on the Maintenance panel must be connected to its default position (Bay 2, Slot 3,
Circuit 2 of a COMBO backplane or Bay 1, Slot 5, Circuit 2 of a 672-port Control Cabinet), to allow
access to the default database from a Superconsole 7000 attendant console connected to this jack,
during installation and initial Customer Data Entry. The card slot must contain a Digital Line Card.
The maximum loop length from the cabinet to the console is 1000 m (3300 
ft) using 26-AWG wire.
The RS-232 printer connector on the back of the Superconsole 1000 attendant console uses the
following pins:
pinsignalpinsignal
1frame ground6dataset ready
2transmit data7signalground
3receive data8carrierdetect
4ready to send20data terminal ready
5clear to send
Page 91
    Add page 98 to Favourites
    image text
    Enable zoom 
    							SECTION MITL9109-094-200-NA
PAEXCROSS
-..--_CONNECT
FIELDMODULAR
JACK
25 PAIR
CONNECTORIZED
CABLE
xSTATION
WIRE(1 PAIR)
CONSOLE
MODULAR
CORDTO ONE CIRCUIT ON
A DIGITAL LINE CARD
NOTE:USE ONLY MITEL CABLE
P/N 559900007 FOR THE
CONSOLE MODULAR CORD.
KAO’IIOEOROFigure 5-22 Superconsole 1000 Attendant Console Installation
Page 92
    Add page 99 to Favourites
    image text
    Enable zoom 
    							Shipping, Receiving, and Installation Information
CHART 5-20
INSTALL UNIVERSAL CARD AND MODULESStepActionComments
1.While wearing the antistatic wrist strap, unpackFigure 5-23 shows a Universal
the universal card(s) and its modules.Card and Modules.
2.Inspect for loose or missing components, andComplete repair tag, repack, and
for damage.return any damaged or incorrect
items.
3.Insert the modules into their assigned locations,Total power rating per universal
press them until they snap into their standoffscard cannot exceed 10.
and then insert the Universal card into its
assigned slot in the card shelf. Refer to Figure5-24.
4.
5.Complete the Tip & Ring Assignment form forFor Tip & Ring assignments for
each module on the Universal Card. Ensure thateach Universal Card module, refer
the correct equipment cross-connections areto Figure 5-25, Table 5-2, and
performed at the MDF to connect this card withTable 5-3. For module power
its associated equipment.ratings, refer to Table 5-4.
If a Console Module is not being installed in
Bay 2, Slot 3, Circuit 1, remove the maintenancepanel cable from J27 of the 
backplane.-TABLE 5-2
BACKPLANE T&R ASSIGNMENTS FOR EACH MODULE POSITION
Module
Position
1Tl RlT2 R2T3 R3
2T4 R4T5 R516 R6
3T7 R7
T8 R8T9 R9
4T10 RlOTll RllT12 R12
Page 93
    Add page 100 to Favourites
    image text
    Enable zoom 
    							SECTION MITL9109-094-200-NATABLE 5-3
TIP 
8i RING ASSIGNMENTS
Module
Tl RlT2 R2T3 R3
TX
nc
Relay 1Relay 2
(subcircult 5) (subcircuit 6)
PA outputrelay contacts
TRI RR1El Ml
Note: The relays on the Receiver card are program-controlled (and are NOT
associated with the DTMF receivers). The relay on the MOH/Pager is
operated when the paging circuit is in use (primarily for controlling an
external amplifier). The system will indicate an alarm and ignore the
universal card if its total module power rating is greater than 10. Therelay contacts must not be used to switch AC mains power to a device,
even if the device draws less current than the contact rating of 0.5 A.TABLE 5-4
MODULE POWER RATING
IModulePower Ratinn
Console
Receiver/Relay
MOH/Pager
E&M Trunk5
2
1
3TABLE 5-5
CONSOLE MODULAR JACK CONNECTIONS
Jack
Pair
PinColour
2yellow
5blackDescription
Tl - line out
Rl - line out
Page 94
    All Mitel manuals Comments (0)

    Related Manuals for Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual