Mitel SMART L CALL CONTROLLER Hardware Installation Manual
Have a look at the manual Mitel SMART L CALL CONTROLLER Hardware Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 55 Mitel manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
SECTION MITL8350-047-102-NA Table 3-l (Cont’d), SMarT-1 tm Hardware Specifications SPECIFICATION DIAL TONE CO SIDE FEED: Gain 300 Hz INTERNAL FEED: 350 Hz DTMF RECEIVER LEVEL LEVEL DIFFERENCE FREQ: To receive To not receive DURATION TIME BETWEEN TONES ROTARY RECEIVER MAKE IMPEDANCE MAKE DURATION BREAK IMPEDANCE BREAK DURATION RATE DTMF SENDER LEVEL FREQUENCY DURATION (Programmable) ROTARY SENDER TIMING (Programmable) TIMING (At 60/40): Make Break RATE (At 60/40) INTERDIGIT PAUSE (Programmable) OPERATING RANGE TEMPERATURE HUMIDITY ALLOWABLE VOLTAGE: connected to any point MIN. -2 -20 -6 -1.5 -3.5 40 30 20 8 20 7 -8 -1.3 40 40/30 35 55 9.9 400 0 0 TYP. 0 n/a -6 60 60/40 10 800 MAX. +2 +3 +6 +I.5 +3.5 700 100 100 20 -3 +I.3 130 60/40 45 65 10.1 1300 55 85 300 UNITS dB darn? dB % % ms ms fi ms KQ ms PPs dBmT % ms ms/ms ms ms PPs ms “C % Volts j+ With reference to 600~ Termination. Page 6
SECTION MITL8350-047-102-NA PARAMETER BAUD RATE: PARITY: BITS PER CHARACTER: BIT EIGHT SENSE: MODE: OPERATION: RS-232 PORT 3.02 Table 3-2 below contains the specifications for the SMarT-I’” Dialer RS-232 Auxiliary Port. This port may be used for pro- gramming or for SMDR Output. Table 3-2, RS-232 Port Specifications SPECIFICATION 110 to 9600 Baud programmable; default = 1200 Baud None Eight bits per character with one stop bit. Space On line. Full duplex mode. ELECTRICAL/MECHANICAL 3.03 Table 3-3 contains the Electrical and Mechanical specifications for the SMarT-1’” Dialer with PAV. These specifications apply to all models of the Controller (4- or 2-line units) unless otherwise noted. 3.04 This section does not contain all of the specifications for the Controller at present. Other specifications will be added as they are received. Table 3-3, Electrical/Mechanical Specifications PARAMETER DIMENSIONS: WEIGHT: Dialer Power MOUNTING: POWER: Range: CONNECTIONS: SUPPlY SPECIFICATION 7.625” (19.37cm) Wide X 10.625” (26.99cm) H X 1.375” (3.49cm) D 2 Ibs (0.907 kg) 1 lb (0.453 kg) (Approximately) Wall Mount with Supplied Bracket 115 Volts AC, 60 Hz 8 300 mA 103.5 to 126.5 VAC Standard RJ31X Network Connections
SECTION MITL8350-047-102-NA 3.05 The specifications in the Tables above are subject to change without notice. The inclusion of ‘n/a’ for a specific parameter means that the specification is not available at the time of this pub- lication. It will be added at a later date. Page 8
SECTION MITL8350-047-102-NA 4. UNPACKING, INSTALLATION AND ORDERING INFORMATION SHIPPING AND RECEIVING 4.01 The SMarT-I’” Dialer with PAV is shipped in a single carton that contains the Dialer, the Power Supply, a Wall Mounting Bracket, four RJ31X Cables and appropriate documentation. All of these items are protected within the carton by Styrofoam inserts. Note: Some production units do not require the wall mounting brackets since these units are mounted to a wall by use of keyslots included on the unit case. 4.02 In some instances where more than one unit is shipped, a larger carton may be used that would contain five of the small- er cartons. Each of the smaller cartons would contain the items listed in 4.01 above. Unpacking 4.03 The procedure below lists steps to take when unpacking the equipment (refer to Figures 4-l and 4-2): 1) Open carton and remove contents. 2) Check each item removed for damage. 3) Check each item against the packing list. 4) Notify the vendor if any items are missing or appear to be damaged or defective. Repacking 4.04 If an item is found to be defective or damaged and is to be returned to the vendor, it should be tagged and packaged to prevent damage. If units are to be shipped from one location to another, these units should also be packaged in such a manner as to prevent damage. Figure 4-1 shows how the equipment was originally packed. This method of packaging should be followed as closely as possible. 4.05 If the original packaging material is no longer available, the returned parts should be wrapped in several layers of air- cushion type of wrap, placed in a suitable container, and surrounded with paper to minimize the movement of the items. INSTALLATION REQUIREMENTS 4.06 The SMarT-1’” Dialer is position independent. It may be mount- ed anywhere that will accommodate the unit size as listed in the specifications in Table 3-3 on Page 7. 4.07 The Dialer will operate within a 0-55°C temperature and a Page g
SECTION MITL8350-047-102-NA RJ31WCA31A CABLES DOCUMENTATIOI DIALER CARDBOARD FLAP DETAIL Figure 4-1, Equipment Unpacking and Repacking Page 10
SECTION MlTL8350-047-102-NA SINGLE UNIT CARTON /-- /-- /-- _-- ‘Y--- /-- /.-- I- MULTI-UNIT CARTON Figure 4-2, Multi-Unit Packing and Repacking Page 11
SECTION MITL8350-047-102-NA O-85% humidity range. POWER REQUIREMENTS The customer must provide a single phase power receptacle with the following recommendations: 115V, 60Hz fused and capable of delivering 350mA per unit installed. The power receptacle should be wired and fused independently from all other receptacles that are not controller related. A warning tag should be attached to circuit breaker type fuses to prevent unauthorized manual operation. The power receptacle should not be controlled by a switch. The live and neutral conductors at the receptacle should be wired to their proper respective connections. The power receptacle must be a 3-wire type, with the ground wire connected to the ground of the electrical system. The receptacle should be easily accessible for the removal of the plug for maintenance. The receptacle location should be selected to prevent acciden- tal removal of the power cord. The power cord between the receptacle and the unit should not present a hazard to the user. MOUNTING 4.09 If the unit requires the wall mounting bracket, simply mount the bracket to a surface with screws. Mount the Dialer housing to the bracket by matching the four holes on the rear of the case with the mounting pins of the bracket. Press firmly into place. 4.10 If the unit is the keyslot type, mount by using the provided template to find screw locations. Insert #6 X 3/4 wood or self- tapping screws in these locations, leaving approximately l/8 inch gap between the surface and the cap-head. Mount the Dialer by positioning the keyslots over the screw heads, pressing toward and then down from the mounting surface. CONNECTIONS Note: The Dialer with PAV should be ing any connections. Refer to initialization procedure. initialized prior to accomplish- Part 6, paragraph 6.06 for the 4.11 Connections to the Dialer are made at the Connector Panel located along the bottom edge of the housing. Figure 4-l illus- trates the connection panel. The steps below outline the connection procedure: Page 12
SECTION MITL8350-047-102-NA TRUNK CONNECTIONS [Cl / COMPUTER PORT (RS-232) [Dl Figure 4-3, Controller I/O Connections 110 VAC cl 0 0 SMART-1 CONTROLLER POWER SUPPLY RJ3lX CA31A ’ 1 L__-_______I ‘L______--____-___I I L-,-,___,,__,__,,,,_,,I =n Figure 4-4, Typical Controller Installation Configuration Page 13
, SECTION MlTL8350-047-102-NA CENTRAL OFFICE LINES MDF DF CENTRAL OFFICE ‘SPLIT’ TYPE DEMARC STATION BLOCK i T_ a-_ T _-_ ST --- -- _ - -- SR - -- - -- - - -- _ EQUIPMENT - -- - - -- _ - -- - ‘66 BLOCK BRIDGE BRIDGE OR RJZlX CLIPS CLIPS 1 1 RJBlX I I MDF OR CAPlA (T) TIP (R) RING L--l-aI-,ld----J I I I Figure 4-5, Typical Connection Configuration 14 20 25 yrJ SIGNAL 1 FRAME GND 2 RxD (Signal in) 3 TxD (Signal Out) 4,5 TIED TOGETHER 6,8,20 TIED TOGETHER 7 GND c Figure 4-6, RS-232 Interface Connector (Viewed from outside Dialer) I Page 14
SECTION MITL8350-047-102-NA 1 I !- Figure 4-7, USOC RJ3lX Jack and Cable ASSY. Page 15