Canon Maxify Ib4020 User Guide

							Setting of the Access Point Mode
The initial value of the access point mode is set as follows.SSID (access point name)XXXXXX-iB4000series
* "XXXXXX" is the last six digits of MAC address of the printer.Security settingWPA2-PSK (AES)PasswordSerial number of the printer
Note
•
To confirm the MAC address of the printer, print out the network setting information.
Printing Out Network Setting Information
•
You can change the security setting and the password using IJ Network Tool.
If you change the access point mode setting of the printer, also change the access point setting of the
external device such as a computer or a smartphone.
211
 
						

							Information about Network Connection
Useful Information about Network Connection
212
 
						

							Useful Information about Network Connection
Default Values Set at Factory (Network)
Connecting the Printer to the Computer Using a USB Cable
When Detecting the Printers Have the Same Name during Setup
Connecting to Other Computer with LAN/Changing the Connection Method
from USB to LAN
Printing Out Network Setting Information
213
 
						

							Default Values Set at Factory (Network)Default Values of the LAN ConnectionItemThe defaultChange LANLAN inactiveSSIDBJNPSETUPCommunication modeInfrastructureWireless LAN securityDisableIP address  (IPv4 )Auto setupIP address  (IPv6 )Auto setupTCP/IP settingsIPv4/IPv6Enable/disable IPv6ActiveEnable/disable WSDActiveTimeout setting1 minuteEnab./disab. BonjourActiveService name (Bonjour settings)Canon iB4000 seriesLPR settingActiveDRX setting  (Wireless LAN )ActiveDRX setting (Wired LAN )Active
Default Values of the Access Point Mode
ItemThe defaultSSID (access point name)XXXXXX-iB4000seriesSecurity settingWPA2-PSK (AES)PasswordSerial number of the printer
(XXXXXX is the last six digits of MAC address of the printer.)
214
 
						

							Connecting the Printer to the Computer Using a USB CableConnect the printer and the computer using a USB cable as the illustration below. The USB port is located
on the rear of the printer.215
 
						

							When Detecting the Printers Have the Same Name during SetupWhen the printer is detected during setup, you may see multiple printers of the same name on the detectionresult screen.
Select a printer with checking the MAC address or the serial number set to the printer against that on the detection result screen.
Note
•
A serial number may not be displayed on the detection result screen.
To check the MAC address of the printer, print out the network setting information.
Printing Out Network Setting Information
216
 
						

							Connecting to Other Computer with LAN/Changing the Connection
Method from USB to LAN
To add the computer connecting the printer with LAN or to change the connection method between the
printer and the computer from USB to LAN, perform setup with the Setup CD-ROM or perform it according
to the instructions on our website.
Connecting to Other Computer with LANTo add the computer connecting the printer with LAN, perform setup with the Setup CD-ROM or perform it
according to the instructions on our website.
Changing the Connection Method from USB to LAN
To change the connection method to LAN while you are using the printer with USB connection, perform
setup again with the Setup CD-ROM or perform it again according to the instructions on our website and
select  Change Connection Method .217
 
						

							Printing Out Network Setting InformationYou can print out the current network settings of the printer.
Important
•
This print out contains valuable information about your computer. Handle it with care.
1.
Make sure that the printer is turned on.
2.
Load a sheet of A4 or Letter-sized plain paper.
3.
Press the  Setup button.
The  Setup menu  screen is displayed.
4.
Use the  button to select  Device settings, then press the OK button.
5.
Use the  button to select  LAN settings, then press the  OK button.
6.
Use the  button to select  Print LAN details , then press the OK button.
The printer starts printing the network setting information. The following information on the printer's network setting is printed out.
ItemExplanations of the itemSettingWireless LANWireless LANEnable/DisableConnectionConnection statusActive/InactiveMAC AddressMAC AddressXX:XX:XX:XX:XX:XXSSIDSSIDSSID of the wireless LAN/SSID of the access
point modePasswordPasswordPassword of the access point mode (8 to 10
alphanumeric characters)Communication ModeCommunication ModeInfrastructure/Access Point ModeChannel *1ChannelXX (1 to 13)EncryptionMethod of the Encryptionnone/WEP/TKIP/AESWEP Key LengthWEP Key LengthInactive/128/64AuthenticationMethod of the Authenticationnone/auto/open/shared/WPA-PSK/WPA2-PSKSignal StrengthSignal Strength0 to 100 [%]TCP/IP VersionTCP/IP VersionIPv4 & IPv6/IPv4IPv4 IP AddressSelected IP Address (IPv4)XXX.XXX.XXX.XXX
218
 
						

							IPv4 Default GatewayDefault Gateway (IPv4)XXX.XXX.XXX.XXXSubnet MaskSubnet MaskXXX.XXX.XXX.XXXIPv6 IP Address *2Selected IP Address (IPv6)XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXXIPv6 Default Gateway *2Default Gateway (IPv6)XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXXSubnet Prefix Length *2Subnet Prefix LengthXXXIPsec *3IPsec settingActiveSecurity Protocol *3Method of the Security ProtocolESP/ESP & AH/AHWireless LAN DRXDiscontinuous reception (wireless
LAN)Enable/DisableWired LANWired LANEnable/DisableConnectionStatus of the Wired LANActive/InactiveMAC AddressMAC AddressXX:XX:XX:XX:XX:XXTCP/IP VersionTCP/IP VersionIPv4 & IPv6/IPv4IPv4 IP AddressSelected IP Address (IPv4)XXX.XXX.XXX.XXXIPv4 Default GatewayDefault Gateway (IPv4)XXX.XXX.XXX.XXXSubnet MaskSubnet MaskXXX.XXX.XXX.XXXIPv6 IP Address *2Selected IP Address (IPv6)XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXXIPv6 Default Gateway *2Default Gateway (IPv6)XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXXSubnet Prefix Length *2Subnet Prefix LengthXXXIPsec *3IPsec settingActiveSecurity Protocol *3Method of the Security ProtocolESP/ESP & AH/AHWired LAN DRXDiscontinuous reception (wired
LAN)Enable/DisableOther SettingsOther settings-Printer NamePrinter namePrinter name (Up to 15 alphanumeric
characters)WSDWSD settingEnable/DisableWSD TimeoutTimeout1/5/10/15/20 [min]LPR ProtocolLPR protocol settingEnable/DisableBonjourBonjour settingEnable/Disable
219
 
						

							Bonjour Service NameBonjour service nameBonjour service name (Up to 52 alphanumeric
characters)DNS ServerGetting DNS Server automaticallyAuto/ManualPrimary ServerPrimary server addressXXX.XXX.XXX.XXXSecondary ServerSecondary server addressXXX.XXX.XXX.XXXProxy ServerProxy Server settingEnable/DisableProxy PortSpecifying Proxy Port1 to 65535Proxy AddressProxy AddressXXXXXXXXXXXXXXXXXXXX
("XX" represents alphanumeric characters.)
*1 Depending on the country or region of purchase, one of the channels from 1 to 11 is printed.
*2 Only when IPv6 is enabled, the status of the network is printed.
*3 Only IPv6 and the IPsec setting are enabled, the status of the network is printed.
220