Vodavi Starplus Triad S Installation Programming Manual

							Speed Dial2-215
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the SPEED flexible button (Button #6). The following message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … System Speed Dialing is enabled at all stations.
Operation
The first programmed attendant uses the same procedures to store system speed dial 
numbers, program multiple speed dial numbers, and to erase existing speed bins as 
described in the operation of station speed dial numbers.
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
System Speed Bin Access
Description
The System Speed Bin Access feature has 900 entries available. A station can be allowed or 
denied access to bins 9100-9999. Access to system speed bins 9020-9099 can not be 
restricted. Stations are granted the ability to dial all Speed Dial Numbers within the specified 
range.
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers
XXX -  XXX  PAGE A
ENTER  BUTTON  NUMBERSXXX      PAGE A
ENTER  BUTTON  NUMBER
XXX-XXX = fixed station range XXX = 3- or 4-digit flexible number
SYSTEM  SPEED 0-1 
ENABLED 
						

							2-216Sp ee d Di al
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #21. The display updates to reflect current programming for Page C.
5. Press the SYS BIN RANGE button (Button #6). The following message displays:
6. Enter a range of speed bins to be allowed (100-999). The leading digit 9 is not reflected on 
the LCD and is not used for your entry.
7. Press HOLD to save the entry.
Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers
STATION ATTRIBUTES
SELECT A STATION RANGEENTER STATION NUMBER
If HOLD is pressed without entering a station range, ALL stations are selected.
Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers
XXX -  XXX  PAGE A
ENTER  BUTTON  NUMBERSXXX      PAGE A
ENTER  BUTTON  NUMBER
XXX-XXX = fixed station range XXX = 3- or 4-digit flexible number
Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers
XXX -  XXX  PAGE C
ENTER  BUTTON  NUMBERSXXX      PAGE C
ENTER  BUTTON  NUMBER
XXX-XXX = fixed station range XXX = 3- or 4-digit flexible number
SYS BIN RANGE 100-999
###-### 
						

							Speed Dial2-217
Chapter 2 - Features and Operation
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Speed Bins/Chaining
Description
Speed dial bins can be chained together. This is helpful for accessing Long Distance carriers 
or banking services when account codes are required.
Operation
 To chain speed bins together, simply press one speed bin and then another as required.
Initialize System/Station Speed Numbers
Description
System and Station Speed bins may be initialized to reset all bins to their original default 
value (empty). All bins 9000-9999 are reset to their default value (empty) upon initializing.
Programming Steps
1. Press the SPEED NO flexible button (FLASH 80, Button #6). The following message 
displays:
2. Press the HOLD button. A confirmation tone sounds.
INITIALIZE  SYS  SPEED   NO
PRESS   HOLD 
						

							2-218Sp ee d Di al
Chapter 2 - Features and Operation
Print System Speed Numbers
Description
The System Speed Numbers command dumps the entire database as a permanent record 
which can serve as a hardcopy of the database. The system baud rate must match that of the 
printer or receiving device.
Figure 2-15: System Speed Numbers Printout
Programming Steps
1. Press the SYSTEM SPEED flexible button (FLASH 85, Button #6). The following message 
displays:
2. To print the System Speed bins, press the HOLD button. The following message displays:
When the system finishes sending the requested information to the printer, a 
confirmation tone sounds.
SYSTEM SPEED NUMBERS
20 37
21 38
22 39
23 40
24 41
25 42
26 43
27 44
28 45
29 46
30 47
31 48
32 49
33 50
34 51
35 52
36 ... and so on through Speed Number 999
PRINT  SYS  SPEED  NO
PRESS  HOLD
PRINTING  SYS  SPEED  NO 
						

							Station Attributes2-219
Chapter 2 - Features and Operation
Station Attributes
Initialize Station Attributes
Description
The Station Parameters may be initialized setting all data fields to their original, default 
values. The following data fields are returned to their default value upon initializing the 
Station Attributes.
Table 2-17: Station Attribute Defaults
Program 
CodeFlexible
ButtonFeaturesDefault Value
(after initialization)
 FLASH 50 1 Paging Access Enabled
PAGE A 2 Do Not Disturb Enabled
3 Conference Enable/Disable (Per Station) Enabled
4 Executive Override Disabled
5 Privacy (Per Station) Enabled
6 System Speed Dial Access Enabled
7 Line Queuing Enabled
8 Preferred Line Answer Enabled
9 Off-Hook Voice Over (OHVO) Disabled
10 Call Forwarding Enabled
11 Forced Least Cost Routing (LCR) Disabled
12 ACD Supervisor Monitor with Barge-In Disabled
13 Executive Override Blocking Disabled
14 CO Line Ringing Options Muted Ring
15 Name/Number Display at Idle Name (Enabled)
16 ACD Zap Tone Disabled
17 CO, Loop, Pool Disabled
18 Admin Access Disabled 
						

							2-220Station Attributes
Chapter 2 - Features and Operation
Programming Steps
1. Press the STATION ATTRIBUTES flexible button (FLASH 80, Button #3). The following 
message displays:
2. Press the HOLD button. A confirmation tone sounds.
FLASH 50
PA G E  B1 Station Identification 006 (24-Btn Keyset)
6 (SLT w/o MW )
2 Station Day Class of Service (COS) COS 1
3 Station Night Class of Service (COS) COS 1
4 Speakerphone/Headset Programming 0=Full Speakerphone
5 Pick-Up Group(s) Programming Group 1
6 Paging Zone(s) Programming Zone 1
8 Line Group Access - Station Group 1
9 LCR Class of Service (COS) 0 (Unrestricted Access)
10 Off-Hook Preference Programming 00=No specific button 
preferred; Enabled
11 Flexible Button Programming (blank)
12 Keyset Mode Inactive Mode
13 Voice Mail ID Translation XXXX=Station #
14 Display Flexible Buttons None
15 Light Control None
17 Cordless Key Telephone Unit (CKTU) Button 00=No button assigned
FLASH 50
PA G E  C1 Internal No Answer Forward None
2Internal Busy Forward None
3 External No Answer Forward None
4External Busy Forward None
5No Answer Timer 10 sec
6 Speed Dial Access None
INITIALIZE   STATIONS
PRESS   HOLD
Table 2-17: Station Attribute Defaults
Program 
CodeFlexible
ButtonFeaturesDefault Value
(after initialization) 
						

							Station Attributes2-221
Chapter 2 - Features and Operation
Print Station Attributes
Description
The Print Station Attributes command can be used to print specific flexible station 
parameters or to print the entire database in fixed number order.
The Print Station Attributes command can dump the entire database as a permanent record 
which can serve as a hardcopy of the database. The system baud rate must match that of the 
printer or receiving device.
When printing the Station attributes the following data prints:
>>> All Current Station Parameters
Figure 2-16: Station Attributes Printout
STATION ATTRIBUTES
STA 100 STA 101
PAGE ACCESS ENABLED PAGE ACCESS ENABLED
DO NOT DISTURB ENABLED DO NOT DISTURB ENABLED
CONFERENCE ENABLED CONFERENCE ENABLED
EXEC OVERRIDE DISABLED EXEC OVERRIDE DISABLED
PRIVACY ENABLED PRIVACY ENABLED
SYSTEM SPEED ENABLED SYSTEM SPEED ENABLED
LINE QUEUING ENABLED LINE QUEUING ENABLED
PREF LINE ANSWER DISABLED PREF LINE ANSWER DISABLED
OFF HOOK VOICE OVER DISABLED OFF HOOK VOICE OVER DISABLED
CALL FORWARD ENABLED CALL FORWARD ENABLED
FORCE LCR DISABLED FORCE LCR DISABLED
ACD SUPV BARGE IN DISABLED ACD SUPV BARGE IN DISABLED
EXEC OVERRIDE BLOCK DISABLED EXEC OVERRIDE BLOCK DISABLED
CO RING OPTIONS MUTED RING CO RING OPTIONS MUTED RING
NAME AT IDLE LCD EXT NUMBER NAME AT IDLE LCD EXT NUMBER
ACD ZAP TONE DISABLED ACD ZAP TONE DISABLED
STATION ID KEYSET - SP 24BTN STATION ID KEYSET - SP 24BTN
CO LOOP POOL FLEX DISABLED CO LOOP POOL FLEX DISABLED
DAY COS 1 DAY COS 1
NIGHT COS 1 NIGHT COS 1
SPEAKERPHONE  FULL SPEAKERPHONE SPEAKERPHONE FULL SPEAKERPHONE
PICKUP GROUPS 1 PICKUP GROUPS 1
PAGE ZONE 1 PAGE ZONE 1
INTERNAL NO ANSWER #### INTERNAL NO ANSWER ####
INTERNAL BUSY #### INTERNAL BUSY ####
EXTERNAL NO ANSWER #### EXTERNAL NO ANSWER ####
EXTERNAL BUSY #### EXTERNAL BUSY ####
NO ANSWER TIMER 10 NO ANSWER TIMER 10
LINE GROUP ACCESS 1 LINE GROUP ACCESS 1
LCR CLASS OF SERVICE 0 LCR CLASS OF SERVICE 0
OFFHOOK PREFENCE BTN 00 ENABLED OFFHOOK PREFENCE BTN 00 ENABLED
KEYSET MODE INACTIVE MODE 2400 KEYSET MODE INACTIVE MODE 2400
VOICE MAIL ID 100 VOICE MAIL ID 101
CORDLESS KEY BTN 00 DISPLAY LCD MSG NONE
BUTTONS: CORDLESS KEY BTN 00
01S0100 02S0101 03S0102 BUTTONS:
04S0103 05S0104 06S0105 01S0100 02S0101 03S0102
07S0106 08S0107 09S0108 04S0103 05C0201 06C0202
10S0109 11S0110 12S0111 07LOOP 08PL03 09CBAK
13L001 14L002 15L003 10PKUP 11DND 12LINEQ
16L004 17L005 18L006 13L001 14SPD 15UNA
19LOOP 20PL01 21CBAK 16ICM 17VMREC 18HFREE
22PKUP 23DND 24LINEQ 19LNR 20SLGIN 21SLOUT
25FLASH 26XFER 27SPEED 22PKUP 23RPARK 24MUSIC
28CONF 29MSG 30FWD
31MUTE 32CAMP 33MON
34HOLD 35VOL 36VOL ... and so on through all stations
NOTE: The button printout for the 8-button keyset displays all flexible AND fixed buttons, the same as the 24-button keyset. 
						

							2-222Station Identification
Chapter 2 - Features and Operation
Programming Steps
1. Press the STATION ATTRIBUTES flexible button (FLASH 85, Button #3). The following 
message displays:
2. To print data for:

All stations, press HOLD.

One station, enter the flexible station number, then press HOLD.
Then the following message displays and the requested information prints:
When the system finishes sending the requested information to the printer, a 
confirmation tone sounds.
Station Identification
Description
Each system port must be programmed to identify the type of station that operate on that 
port. Each station type must be identified.
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
PRINT  STATIONS
PRESS  HOLD
PRINTING  STATIONS
When identifying a station as a DSS / DLS console, you must also enter the station 
number of the key telephone to which the DSS / DLS console is associated. To 
associate a DSS console with Station 100, the entry would be 1100 [HOLD].
Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers
STATION ATTRIBUTES
SELECT A STATION RANGEENTER STATION NUMBER 
						

							Station Identification2-223
Chapter 2 - Features and Operation
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display updates to reflect current programming for Page B.
5. Press the STATION ID flexible button (Button #1).
6. Enter a valid number on the dial pad to identify type of telephone:
7. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … All Key Telephone Boards (DTIB) default to ID 006 (24-Button Digital Telephone), 
all Single Line Boards (SLIB) default to ID 6.
If HOLD is pressed without entering a station range, ALL stations are selected.
Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers
XXX -  XXX  PAGE A
ENTER  BUTTON  NUMBERSXXX      PAGE A
ENTER  BUTTON  NUMBER
XXX-XXX = fixed station range XXX = 3- or 4-digit flexible number
Flash 50 - Fixed Numbers Flash 51 - Flexible Numbers
XXX -  XXX  PAGE B
ENTER  BUTTON  NUMBERSXXX      PAGE B
ENTER  BUTTON  NUMBER
XXX-XXX = fixed station range XXX = 3- or 4-digit flexible number
STATION  ID 0-8
KEYSET - SP 24BTN
[1-2] = DSS Console [007] = 12-Btn Phone
[6] = SLT w/o Msg Wait [008] = 8-Btn Phone
[7] = SLT w/Msg Wait (90 VDC) [015] = SLA
[006] = 24-Btn Phone [016] = Lg Disp 30-Btn Phone
When designating a station as a DSS Console with map 1 or map 2, you must follow 
the entry with the station number for which the DSS is to be associated. Refer to 
“Station ID for DSS / BLF Console With Map” on page 3-18. 
						

							2-224Station Identification
Chapter 2 - Features and Operation
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Station ID Lock
Description
The Station ID Lock feature provides a means for the installer/programmer to lock the station 
ID of all stations in the system. After locked, attempts to plug unlike devices (e.g., a DSS into a 
24-button port) results in the device not working. This feature is designed to prevent loss of 
station programming that results when a different station type is plugged into a port already 
designated as another station type.
To change the Station ID with the Station ID Lock feature enabled:
1. Enter programming mode and disable the Station ID Lock feature.
2. Plug the new device type into the jack. The set is automatically identified.
3. Enter programming and perform Station ID programming (FLASH 50, Page B, Button #1). 
Set is automatically identified.
4. Enter programming mode and enable the Station ID Lock feature.
Programming Steps
1. Press the STATION ID LOCK flexible button (FLASH 06, Button #8). The following 
message displays:
2. Enter a 0 or 1 on the dial pad to enable/disable the use of this feature.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Station ID Lock feature is disabled.
STATION  LOCK 0-1
DISABLED