Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

							infinite n Digital SystemsTF NO: 53-.
Direct Inward Dialing (Cont’d)
Programming Steps:
1.Press FLASH and dial [24]. The following message will be shown on the display:
Where:
S 
= Station Board (KT12)
C 
= CO Line Board (CO12)/DlD
D 
= DTMF/Sta Combo Card
E 
- TIE Line Interface Board (TIE)T 
- Tl Trunk card
##- Blank (unused card slot)
- 2. The buttons 1 through 18 indicate peripheral card slots 1 through 18. When the Flexible Card Assignments
program is initially entered, Flex Button 
#l LED will be lit indicating that the user ,fs programming the card in
peripheral card slot 1. Press the appropriate flex button for a different peripheral card slot.
3.Enter a one-digit to indicate the type of card is plugged into the current peripheral card slot.
0 
- Key Telephone Board (KT12) or Single Line Board (SL12)
1 
- CO Loop Interface Board (CO12)/DiD Interface Board
2 
- TIE Line (E&M) interface Board
3 
- 8x8 Combo Card
4 
- Tl Interface Board
#I Delete slot
Vodav Communication8 !Sysbms
Page 8 of 27TF NO. 53
8300EkiflhDfiWscot$dale,Az85260w4 44s@oo 
						

							infinite ” Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
4.Press the HOLD button to complete the entry. Confirmation tone will be heard and the display will now update.
NOTE: 
Affer the card slots have been re-arranged, the system MUST be reset for full activation of the database
programming to take effect.
Default: The system defaults to a configuration that designates peripheral slots 1,2,3 and 4 for Station boards,
peripheral slots 
5,6,7 and 6 for CO boards, and peripheral slots 9, 10, 11 and 12 for the remaining station boards.
Slots 13 thru 16 are unassigned by default.
Page 9 of 27
TF NO. 53
83OOEReintreeDrivescaclak,Az85260w ~ 
						

							infinite m Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
A. Direct Inward Dialing (DID) Table Programming:
The buttons on the digital terminal are defined as shown below when entering the DID programming area:
1.Press FLASH and dial 1441. The following message is shown on the display phone:
Where:
- RRR- Route Number (000-199)
- ###I DID Number (Directory W from C.O.) (7 digits)
- n..n- Name Assigned to DID Number (8 characters)
To program the Route Number:
1.The top left button (ROUTE) in the flexible button field will be lit for programming the Route number. The LEDs
for the UP Button (Button 
#18), the DOWN Button (Button #19) will also be lit.
wTo change to a different DID Route Number, press either the UP Button (Button #18), or the DOWN Button
(Button 
#19).
2.Enter the threedigit Route Number (000-199) to be associated with the DID Number. This Route Number is
the same Route Number in the 
ICLID Ringing Assignments Table (Flash 43) and determines the destination
of the DID number associated with this Route Number.
3.The display will show the route number as it is entered. Press the HOLD button to save the entry. Confirmation
tone will be heard.
Vcdavi Communications Sysbmr,
Page 10 of 27TF NO. 53
E3wERain~hfsco~Az8960w - 
						

							Infinite n Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
To program the DID Number:
1.Press the NUMBER Button (Button #2) in the flexible button field for programming the DID Number.
2.Enter the DID Number to be associated with a three-digit Route Number (009199). Up to 7 digits can be
entered. By default, only the last three digits will be used for routing. Thii is determined in Flash 45. (Refer to
Page 8).
3.The display will show the DID number as it is entered. Press the HOLD button to save the entry. Confirmation
tone will be heard. If the DID number is already in the DID Translation Table, the Route Number associated
with the DID number 
will be displayed.
NOTE: By default, the DID Table is 
filled with numbers. If error tone is received when the HOLD button is pressed,
the DID Table is full and an entry needs to be deleted to make room for this new phone number.
To program the name assigned to the DID Number:
1.Press the NAME Button (Button ##3) to program the desired name for the DID trunk. Maximum number of
characters is eight. The BACK SPACE Button (Button #5) can be used to erase the current letter to correct for
errors.
The following table is used for name entries.
3.The display will show the DID Name as each letter is entered. Press the HOLD button to save the entry.
Confirmation tone will be heard.
v&vi -cations sysbm
Page 11 of 27TFN0.53
63OOERaintreeDriwscott3dale,&8960’@=I-I
._.. _ 
						

							infinite n Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
To erase a DID Table entry:
1.Press the CLEAR ENTRY Button (Button #4) to clear an entire Phone Number, Name and Route from the DID
Table. Press the HOLD button to save the entry. Confirmation tone will be heard and the entry cleared.
To change to a different DID Route:
1.Press the UP Button (Button #18) to advance to the DID Route Number.
OR
2.Press the DOWN Button (Button #19) to go back to a previous DID Route Number.
Default:By default, all entries in the DID Table (000-999) have phone numbers assigned. The following table
shows the default configuration for the DID Table entries and the ICLID Ringing Assignment Table:
I999I199I199
I499I
l Route 009 in the ICLID Ringing Assignment Table is used as the intercept route. Calls to numbers not contained
in the DID table will follow Route 000. If Route 000 is defaulted to “none”, the call will follow Route 001.
Page 12 of 27TFN0.53
83OOEfhinteeDrivescott9a,k896o(so2) 443aw
_. 
						

							inttnite m Digital Systems
Direct Inward Dialing (ConY)
B. Direct Inward Dialing Parameters:TF NO: 53
The buttons on the digital terminal are defined as shown below when entering the DID programming area:
1.Press FLASH and dial [45J. The following message is shown on the display phone:
To program the number of DID digits:
1.Press the DIGITS Button (Button #l) in the flexible button field for programming the number of digits the system
will look at for routing purposes. The following message is shown on the display phone:
2.Enter a one-digit entry (2-7) on the dial pad which corresponds to the number of digits used for the routing of
the DID number.
3.Press the HOLD button to save the entry. Confirmation tone will be heard and the display will update.
Default: By default, the number of DID digits is set to 3.
To program the type of DID Signaling:
1.Press the SIGNALING Button (Button #I2) in the flexible button field for programming the type of DID signaling
desired. The following message is shown on the display phone:
s
2.Enter a one-digit entry (O-l) on the dial pad.
[0] 
= Wink
[l] - Delay
Page 13 of 27TF NO. 53
83OOEWntmDriwScomk8526u@w 443-mo 
						

							infinCfe ” Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
3.Press the HOLD button to save the entry. Confirmation tone will be heard and the display will update.
Default: By default, the type of DID Signaling is set for wink
To change the Wink Timer:
1.Press the WINK TIMER Button (Button #3) in the flexible button field for changing the Wink Timer settings. The
following message is shown on the display phone:
2.Enter a three-digit value on the dial pad which corresponds to 100-300 milli-seconds.
3.Press the HOLD button to save the entry. Confirmation tone will be heard and the display will update.
Default: By default, the Wink Timer is set for 140 milli-seconds.
To change the Delay Timer:
1.Press the DELAY TIMER Button (Button #4) in the flexible button field for changing the Delay Timer settings.
The following message is shown on the display phone:
2.Enter a threedigit value on the dial pad which corresponds to 000-200 milliseconds.
3.Press the HOLD button to save the entry. Confirmation tone will be heard and the display will update.
Default: By default, the Delay Timer is set for 140 milliseconds.
Page 14 of 27TF NO. 53
83lOERaintrwDrksa&dak,kB’@=I 443emo 
						

							infinlfe ” Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
C. 
InNalization of DID Tables:
Description:This section describes the procedures and steps necessary to initialize the system database returning 
any
programmed data to 
its original or default value. The entire system database may be initialized or various portions
of the database may be individually initialized. In addition to initialization of the entire database, a system reset
(Button 
#20) command is also included in this section for clearing meantime errors without initializing the database.
The buttons on the digital terminal are defined as shown below when entering the Initializing 
DataBase ParameterS
programming area:
Programming:
1.Press FLASH and dial (801. The following message is shown on the display phone:
If the 
ICLID/DID Table(s) need to be initialized:
-2.Press the lCLlD/DID TABLES Button (Button #9). The following message will be shown on the display phone:
3.To initialize the ICLfD/DID Table(s), press the HOLD button. Confirmation tone will be heard.Page 
15of 27TF NO. 53
8300ERahtmeDrive-Ar=w4 - 
						

							infinite m Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
If the DID Timers need to be initialized:
1.Press the DID-TIE TMRS Button (Button #14). The following message will be shown on the display phone:
3.To initialize the DID Timers, press the HOLD button. Confirmation tone will be heard.
Vcdavi bmmunicetions Systems83DOE.&ll@WDrive
Page 16 of 27
saadak,k8960TF NO. 53w4 4434ow 
						

							Infinite ” Digital SystemsTF NO: 53
Direct Inward Dialing (Cont’d)
D. Printing of DID Tables:
Description:
This section describes the procedures and steps necessary to print Data Base Parameters and various portions of
the system.
The buttons on the key telephone are defined as shown below when entering the Print Data 
Bass Parameters
programming area.
With a printer connected to the RS-232C port (Port 
#3) on the Backplane I/O Expansion Module, the currently stored
customer database can be printed or “downloaded” to a file. This command allows the entire database to be
“dumped” as a permanent record which can serve as a hard copy of the database .
The system Baud rate must match that of the printer or receiving device.
Defautt: None
Related Programming: Refer to Sec. 710.10, Baud Rate Assignments for setting the baud rate of the RS-232C
port on the Backplane 
f/O Expansion Module on the infinite DVX “I system.
Page 17 of 27TF NO. 53
83OOE&lbMDliWsuAtde,Az8960’@=I ~