Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

							infinite” DVX I’BASIC 
KEYSET FEATURE OPERATIONDigital Key Telephone System
- [9] = busy and no answer calls.
Skipthe precedingstep forimmediate
4.Dial the three-digit Voice Mail group pilotnumber (440-447) for the group (l-8)
where calls are to be forwarded. Confirma-
tion tone will be heard.
5.Replace the handset or press the ON/OFFbutton.
To cancel Call Forwarding:1. Lift the handset or press the ON/OFF
button.
2. Dial the Call Forward Cancel code, 
[662]
on the dial pad,
or
Press the pre-programmed* FWD flex but-
ton. Confirmation tone will be heard.*Refer to Sec. 400.37, Flexible Button
Assignment.H.Call Forward 
- Hunt Groups
If you have been given the ability to forward
your calls:
1.Lift the handset or press ON/OFF button.2. Dial the Call Forward code, 
[640] on the
dial pad,
or
Press the pre-programmed* FWD flex but-
ton.3. Dial the desired code:
- [7] = no answer calls
- [8] = busy calls
- [9] = busy and no answer calls.
Skipthe precedingstep forimmediate
4.Dial the three-digit Hunt group pilot num-ber (450-457) for the group (l-8) where
calls are to be forwarded. Confirmation
wtone will be heard.
5.Replace the handset or press the ON/OFFbutton.
To cancel Call Forwarding:1. Lift the handset or press the ON/OFF
button.
2. Dial the Call Forward Cancel code, 
[662]
on the dial pad,
or
Press the pre-programmed* FWD flex but-
ton.*Refer to Sec. 400.37, Flexible Button
Assignment.405.5CALLING STATION TONE MODE
OPTION
The Basic keyset will initialize to the handsfree
mode any time it is powered up or reset. If theuser is in the tone ringing mode, he will be
returned to the handsfree mode if the power is
turned off or the system is reset.
When the tone ringing mode is desired:a. Dial the Tone Mode Option code 
[667] on
the dial pad. This code will toggle between
the handsfree and tone ringing mode.405.6CONFERENCE WITH PERSONAL
PARK
While connected to an outside line:
a. Press the TRANS button. Transfer dial tone
is heard.
b. Dial 
[438] on the dial pid. (1 st call is placed
in personal park).
c. Dial desired number for 2nd call.d. Press the TRANS button again. Transfer
dial tone is heard.
e. Dial 
(6641 on the dial pad. All three parties
are 
conferenced.f. Replace the handset to terminate confer-
ence.405.7CO LINE QUEUING
A station can queue only one line at a time. If
you see that a particular outside line is busy
and you wish to be placed on a list waiting for
that line to become available:
To Place a Queue:
a. Press the Pool button. Busy tone is heard.b. Press the pre-programmed* LINE QUEUE
button.
c. Replace the handset.
To Answer a Queue:If you hear ringing and an outside line of the
line group (or a Loop or Group Key), you queued
onto is rapidly flashing:a. Lift handset or press ON/OFF button.
b. Press flashing Pool button to answer.
If lyour station has betm pn-grtzmmed forPrqfmd Line Answer, you will have theline automaticalLy upon lifting the handset.
*A flex button must be programmed for this
feature to operate. Refer to Sec. 400.37, Flexible
Button Assignment.405-S
Issue 1, February 1994 
						

							infhitem DVX I’Digital Key Telephone SystemBASIC 
KEYSET FEATURE OPERATION
405.8DIRECTED CALL PICK-UP
When incoming, transferred, or recalling out-
side line ringing, intercom ringing, or Camp On
ringing is heard at an unattended telephone:
a. Dial the station number of the known ring-ing telephone. Receive 
ringback tone, or
call announce tone.b. Press the pre-programmed* PICK UP but-
ton to answer the call.*A flex button must be programmed for this
feature to operate. Refer to Sec. 400.37, Flexible
Button Assignment.
Conditions:l User must have access to the specific
outside line or a Loop button to do a
directed call pickup.405.9DO NOT DISTURB
If you have been given the ability to place yourphone in Do Not Disturb:
a. Lift the handset or press the ON/OFF but-
ton.b. Dial the Do Not Disturb code 
[631] on the
dial pad,
or
Press the pre-programmed* DND button.
DND button lights steady.
Removing Do Not Disturb
a. Dial the Do Not Disturb code 
[631] on the
dial pad,
or
Press the pre-programmed* DND button.
The button LED extinguishes and DND is
canceled.*Refer to Sec. 400.37, Flexible Button
Assignment.405.10 MESSAGE WAITING
If you dial a station that is busy, unattended,
or in DND, you can leave a message waiting
indication.
a. Lift the handset or press the ON/OFF but-
ton.b.Dial the desired intercom station. Busy
tone or DND tone is heard.
c. Press the TRANS button. Transfer dial tone
is heard.d. Dial the Message Wait code 
[623] on the
dial pad. Confirmation tone is heard.e. Replace the handset or press ON/Off but-
ton to end the call.Up to 
fivemessages canbekft atany
Answering a Message Waiting Indication
If your MSG WAIT lamp is flashing, you have a
message waiting for you. The first message left
will be the first one called.
a. Lift the handset or press the ON/OFF but-
ton.
b. Dial the message wait return code 
[663] on
the dial pad. Station that left message will
be signaled with tone ringing.
c. If called station does not answer, press theTRANS button. After receiving transfer
tone, dial the message wait code 
[623] to
leave message.*Refer to Sec. 400.37, Flexible Button
Assignment.405.11 
MUTE KEY
The MUTE feature provides privacy during
speakerphone or handset operation by dis-
abling the microphone.
To activate the Mute feature:a. Press the pre-programmed* MUTE button
while off-hook on speakerphone or hand-
set to activate.
To de-activate the Mute feature:a. Press the pre-programmed* MUTE button
again to deactivate.mute featureautomatically
*A flex button MUST be programmed for this
feature to operate.*Refer to Sec. 400.37,
Flexible Button Assignment.405.12 PBX/CENTREX TRANSFER
While connected to an outside line 
(PBX/Cen-
trex) :
a. Press the TRANS button. Receive transfer
dial tone.b.Dial 
[660] on the dial pad. A flash com-
mand will be presented to the PBX or Cen-
trex line. PBX or 
Centrex studder tone will
be heard.
c. Dial desired outside number.
d. Replace handset to complete transfer.405.13 PERSONAL PARK (Flip-Flop)
While connected to first call:
a. Press the TRANS button. The caller is puton Exclusive Hold.
Issue 1, February 1994
405-9 
						

							BASIC KEYSET FEATURE OPERATIONinfinite” 
DVK I’Digital Key Telephone System
b. Dial the Personal Park code 
(4381 on the
dial pad,
or
Press a pre-programmed* flex button. (callis placed in personal park). Dial tone will
be heard.The user can 
aZtemateZy connect to the
other call bg pressing the TRANS button
and dialing [4381 as many times as
necessary.
Retrieving a Parked Call:a. Dial the Personal Call Park location code
[438] on the dial pad,
or
Press the pre-programmed* PERSONAL
PARK button.
Both the station and the call will receive a
warning tone and then a talk path is estab-
lished between the two parties.405.14 
PROGRAMMING YOUR NAME
INTO THE LCD DISPLAY
The Basic Digital Terminal has the capability
for the user to program his name so that people
using display telephones will see the name in-
stead of the station number.
a. Lift handset.b. Dial 
[690] on the dial pad.
c. Enter your name (up to 7 letters) using thepattern shown below.
A=21M 
=611 =l#“ =OlB 
=22N =622 =2#, =02C 
=230 =633 =3#? =03D 
=31P=714 =4#/ =04E 
=32Q =745 =5#1=*1F 
=33R =726 =6#$ =*2G 
=41s =737 =7#& =*4H 
=42T=818 =8#* =*#
.I =43U =829 =9#(=#lJ 
=51V =830 =O#) =#2K 
=52w=91Space = 11+ =#3L 
=53x =92: =12= =#4Y 
=93- =13# =##
z =94’ =14d. Press the SPEED button to complete the
programming process.405.15 VOLUME CONTROL
A “slide” switch is provided on the front of the
in&&e Basic Digital Terminal to adjust the
volume of the voice and tones presented to the
terminal speaker.
- The “slide” switch controls the speaker
volume which controls all voice signals
sent to the speaker i.e. Speaker Phoneconversations, BGM, and Page an-
nouncements.
-The same “slide” switch also controls theringing volume which controls all tone
signals presented to the speaker i.e.
Ringing, splash tones, Camp-On etc...
Muted ringing is also controlled by the
slide switch. The muted ringing volume
will be proportionately quieter than nor-
mal ringing based on the current switch
setting.
Q405-10
Issue 1, February 1994 
						

							infznitem DVX I’Digital Key Telephone System
SLT FEATURE OPERATION
SECTION 410SLT FEATURE OPERATION
410.1INTRODUCTION
This section of the manual contains the operat-
ing instructions for Single Line users. It is de-signed to provide step-by-step instructions for
operating the Single Line telephones in the
system.Literature similar to these operating instruc-
tions has been prepared for use by the customerin the form of a Single Line Telephone User’s
Guide.
410.2ACCOUNTCODE
SLT stations can enter an account code to iden-
tify the call or calling station.
Entering Account Code before a call:
a. Lift the handset.b. Dial 
[627] on the dial pad.
c. Dial the account code. If the account codecontains fewer than la-digits, dial 
I%] to
return to intercom dial tone. Dial tone is
heard.
d. Dial 
191 or CO Access code and the desired
number.
Entering Account Code during a call:a. Depress the hookswitch momentarily.
Your call will be placed on hold while you
enter your account code.b. Dial 
[627] on the dial pad.
c. Dial the account code. If the account codecontains fewer than 
12digits, dial [X] to
return automatically to the call.
410.3AUTOMATIC CALL DISTRIBU-wTION (ACD)
Thisfeature is available with optional soft-
ware. When purchased, Uniform Call Distribu-tion (UCD) is not used and is replaced by the
ACD functions identified in the following. 16
Automatic Call Distribution (ACD) groups can
be programmed, each containing up to 16
three-digit station numbers.A. Agent 
Login/Logout Feature
The Agent Login/Iogout feature provides ameans for an agent to log into one of the
ACD groups and receive calls. For an agentto be placed into an active ACD state, the
agent must first login.1. Dial the 
LOGIN CODE [572] on the dial
pad, followed by the ACD group number
(5x4 that the agent is going to log into.2. The agent enters his unique AGENT ID
code (0000-9999). Confirmation tone is
heard and the agent is logged onto the
ACD group. When the agent logs in, an
ACD login event is sent to the SMDR port,
if active.If Q member is assigned to Q 
specifa ACD
~~enter and exzt an AW group other than hrsFor an agent to remove himself from the ACD
group as an active agent:
1.Dial the LOGOUT CODE [57 l] on the dial
pad. When the agent logs out and removeshimself from the ACD group, an ACD 
lo-gout event is sent to the SMDR port, if
active.
Conditions:l
If an agent logs into an ACD group froma station that is logged into another
ACD group, the station will be automat-ically removed from the previous ACD
group.
l An agent may log out while in wrap-up,
or unavailable.l An agent logging in will first be placed
in wrap-up mode before receiving an
ACD call.
l If an agent attempts to log into an ACD
group that already has 16 members,
that agent will receive error tone.l
The i.n@ntie Digital System will not verifyagent’s ID codes, other than requiring
four digits to be entered.
B.ACD Agent “HELP” button
The ACD Agent “HELP” feature provides a
means for an ACD agent to signal his as-
signed supervisor for assistance.
While on a call in progress, the agent:1. After hook-flashing, dial the “HELP” code
on the dial pad. The agent must 
hook-flash again to return to his call after the
code is dialed. If no supervisor is logged in,the agent will receive one-burst of error
Issue 1, 
February 1994
410-l 
						

							infznite” DVX InSLT FEATURE OPERATION
Digital Key Telephone System
2500 Type
2500 Type 
w/Msg Waiting Lamp on Top
2500 Type w/Message Waiting Lamp
2500 Type Wall Phone2500 Type w/Flash Key
410-2Issue 1, February 1994 
						

							infznitem DVX I’Digital Key Telephone System
SLT FEATURE OPERATION
Table 410-l SLT Numbering Plan
100-195
420 
ma421 
[=a43 
[Cl438
44 
WI45 
[HI55 
WI55 
WI56 
WI566
571572 55 [U]
6# [=I620
621622
623
624
625
626
627
631
633 [ZZ]633 [00]
638+[0-91
638+[%]
638+[#]640
640 
[7]640 
[8]640 
[9]640 
[SAC]660
661 
(YYj662
663
664
Station Intercom Numbers
Voice Mail Enable MSG Wait
Voice Mail Cancel MSG Wait
Call Park Location O-7 (system)
Personal Park
Voice Mail Group Pilot Numbers O-7
Hunt Group Pilot Numbers O-7
ACD* Group Pilot Numbers O-9
UCD Group Pilot Numbers O-7ACD* Group Pilot Numbers 
lo-15
ACD*/UCD Available/Unavailable
ACD* Agent LogoutACD* Agent 
Login
Tone Mode Ring Option
Camp-On
Line QueueCall Back
Message Wait
Conference
Executive Override
LCR Queue Cancel
Account Code Enter
Do Not Disturb
Personalized Messages
Clear Personalized Messages
Handset Receiver Gain
Handset Receiver Gain Increase
Handset Receiver Gain DecreaseAll Call Forward
No Answer 
- Call Forward
Busy 
- Call Forward
Busy/No Answer 
- Call Forward
Off-Net - Call Forward
SLT Flash Command to CO Line
SLT Station Speed Dial Programming
SLT Clear 
- Call Forward, DND,
Personal Messages
Message Wait return
SLT Conference 
W/ Personal ParkSLT Speed Dial Access
Name in Display Programming
All Call Page (Internal 
& External)
Internal Page Zone 1
Internal Page Zone 2
Internal Page Zone 3
Internal Page Zone 4
Internal All Call Page
External All Call Page (All Zones)External Page Zones l-7
Meet-Me-Page Answer
CO Line Group 1
(if LCR is enabled)
CO Line 
Gropp 2
CO Line Group 3
CO Line Group 4
CO Line Group 5
CO Line Group 6
CO Line Group 7
All CO line Groups
(CO Line Off-Net Forward)
LCR or CO Line Group 1
(if LCR is disabled)
Attendant
Group Call Pick Up (Key 
& SLT)
Directed Call Pick-up 
(SLT)
Call Park Pickup (Key and 
SLT)
Universal Night Answer668 
ywl690
70
71
72
7374
75
76 101
76 PI
77
81
8283
84
85
86
87
88
9
0
#O
#l [=I
#43 [Cl
#5
XXX = Intercom Station Numbers
W = Speed Dial Bin numbers
ZZ = Personalized Messages
U = ACD* (O-15), UCD (O-7) Group Number
C = 
CaIl Park Location O-7
H = Hunt Group Number O-7
V = Voice Mail Group Number O-7
P = External Page Zone Number l-7
*Features available with optional software.Issue 1, February 1994
410-3 
						

							SLT FEATURE OPERATIONinfinitem DVX I’Digital Key Telephone System
tone. The ACD supervisor station receivesa “HELP” message if a member of one of
the ACD groups he is assigned to initiatesa “HELP” request. The “HELP” function
also sends a Camp-On tone to the speakerof the supervisors 
keyset. The “HELP”
message takes precedence over any other
message and can be cleared by the super-visor by pressing his “HELP” button.
At the time the supervisor receives a
“HELP” request, he can press his “HELP”
flex button followed by his override featurebutton to bridge onto the ACD group
members call. The “HELP” button will
place an intercom call to the station re-
questing “HELP”. The “HELP” message
will be cleared after the supervisor’s
“HELP” button is depressed. In addition,
the “HELP” message will be cleared if the
agent was on a call and went back on hookbefore the supervisor could respond. In
this case, the “HELP” message will be con-
verted to a message wait indication.
Conditions:l Up to five messages can be left at any
supervisor station.
0 The supervisor can cancel the “HELP”
request signal by depressing his flash-
ing “HELP” button. In addition, a call
will be placed to the agent requesting
“HELP”. If the agent is on a call, the
supervisor can press his barge-in but-
ton to monitor the call or give assistance
on the call.C. ACD 
AvaiIable/UuavaiIable Mode
If you are a ACD agent, you may place yourstation in the Available mode to receive
ACD type of calls or you may place your
station in the Unavailable mode to block
wACD type calls from ringing your station.
To go Available:1. Dial 
[566] on the dial pad. Confirmation
tone will be heard through the handset.
You may now receive ACD calls.
To go Unavailable:1. Dial 
[5661 on the dial pad. Confb-mationtone will be heard through the handset.
You are now blocked from receiving ACD
calls.
410.4CALL BACK
You call a busy station and receive busy:a. Briefly depress and release the 
hook-
switch.b. Dial 
[622] on the dial pad.
c. Replace handset.
OnZg one Call Back request can be left at a
station; the second request wiZZ convert to
Message Waiting Request.
410.5CALL FORWARDING
To call forward calls to another station:
a. Lift handset.b. Dial 
[640] on the dial pad.
c. Skip Step c. for immediate forwarding, oth-
erwise dial the appropriate code:
- [7] = CaIl Forward No Answer
- [S] = Call Forward Busy
- [9] = Call Forward Busy/No Answer
- [a] = Call Forward,Off-Net (via speed
dial)d. Dial the three-digit extension number or
speed bin number where calls are to be
forwarded. Confirmation tone will be
heard.
e. Replace handset.
To Remove Call Forwarding:
a. Lift handset.b. Dial 
[640] on the dial pad or [662] on the
dial pad. Confirmation tone will be heard.
c. Replace the handset.410.6CALLING STATION TONE MODE
OPTION
Allows a calling station to override a called key
station’s 
“HF” or “PV” intercom switch setting.When placing a call to a key station and Tone
ringing is desired:a. Dial 
[6#] on the dial pad.
b. Dial three-digit station extension (call tone
rings station).
410.7CAMP-ON
After receiving intercom busy tone:a. Briefly depress and release the 
hook-
switch.
b. Dial 
[620] on the dial pad. When the called
party answers, consult with them.
While on a CO line you receive a Camp-on
warning tone through handset:a. Choose desired call (hang up on present
calI and take the new one, or ignore the
Camp-on signal). (also see Personal Park)410-4
Issue 1, February 1994 
						

							infmitem DVX I’Digital Key Telephone SystemSLT FEATURE OPERATION
410.8CALL PARK (System)
To place an outside call on hold and consult
with, page, or call an internal party before
transferring the outside call.
While connected to an outside line:
a. Depress and release the hookswitch. The
caller is put on Exclusive hold.b. Dial parking location (430 to 437) on the
dial pad. 
Confirmation tone is heard.
c. If you hear busy tone, depress and releasethe hookswitch and dial another parking
location.
Retrieving a Parked Call
a. Lift handset.b. Dial a pound 
[#I on the dial pad.
c. Dial parking location (430 to 437) where
the call was parked.
410.9CALL TRANSFER:
Making an Unscreened Transfera. Briefly depress and release the 
hook-
switch.
b. Dial desired intercom number.
c. Hang up to complete the transfer.
Making a Screened Transfer:a. Briefly depress and release the 
hook-
switch.
b. Dial desired telephone number. Announce
the call.
c. Hang up to complete the transfer.410.10 CLEAR CALL FORWARD, DND,
PERSONALIZED 
MESSAGES
SLTs can activate and cancel call forward by
dialing [6401 on the dial pad and DND by dialing
16311 and enable and cancel personalized mes-sages by dialing 
[633xx].
A convenient code 
[6621 has been incorporatedto cancel either Call forwarding, DND, or Per-
sonalized Messages when the SLT user has
forgotten which code has been programmed on
the phoneTo cancel Call Forward, DND, Personalized
Messages:a. Lift handset. Notification tone will be
heard.b. Dial 
[6621 on the dial pad. Confirmation
tone will be heard.
c. Replace the handset.410.11 CO LINE QUEUING
a. Dial outside line access code. Receive busy
tone.b.Briefly depress and release the 
hook-
switch.c. Dial 
[621] on the dial pad. Con&nation
tone is heard.410.12 CONFERENCE
You may set up a conference of 1 external and
1 other internal station.
a. Lift handset.
b. Make outside call.
c. Briefly depress and release the hookswitchto put the call on hold.
d. Dial number of interpal station you wish toadd.
e. When that station answers, briefly depress
and release the hookswitch again and all 3
parties will be connected.410.13 CONFERENCE WITH PERSONAL
PARK
While connected to an outside line:
a. Depress the hookswitch momentarily. In-
tercom dial tone is heard.
b. Dial 
[438] on the dial pad. (1 st call is placed
in personal park).
c. Dial desired number for 2nd call.
d. Depress the hookswitch momentarily. In-
tercom dial tone is heard.
e. Dial 
[664] on the dial pad. All three parties
are 
conferenced.
f. Hang up to terminate conference.
410.14DIRECT OUTSIDE LINE ACCESS
a. Lift handset.
b. Dial access code 
(9,8 1 - 87) on the dial pad.
c. Dial desired telephone number.410.15 DIRECTED CALL PICK-UP
Upon hearing an unattended telephone ring:
a. Lift handset.b. Dial 
[# 11 on the dial pad.
c. Dial station number of ringing telephone.
You will be connected to intercom, incom-
ing, recalling or transferred outside line.410.16 DO NOT DISTURB
Activating Do Not Disturb:
a. Lift handset.b. Dial 
[631] on the dial pad.
Issue 1, February 1994410-5 
						

							SLT FEATURE OPERATIONinfinitem DVX I’Digital Key Telephone System
c. Replace handset.To cancel Do Not Disturb:
a. Lift handset.b. Dial (6311 on the dial pad or 
[662] on the
dial pad.
c. Replace handset.410.17 PBX/CENTREX TRANSFER (Flash
Command to CO Line)
To initiate a PBX or Centrex Transfer command
from an SLT.
While connected to a PBX or 
Centrex line:a. Briefly depress and release the 
hook-
switch. Intercom dial tone will be heard.b. Dial 
[6601 on the dial pad. A Flash com-
mand will be presented to the PBX or Cen-
trex line.
c. PBX or 
Centrex studder tone will be heard.
Dial number of desired extension.
d. Replace handset to complete transfer.410.18 GROUP CALL PICK-UP
Upon hearing an unattended telephone ringing:
a. Lift the handset.b. Dial [#0] on the dial pad. You will be con-
nected to intercom or transferred or recall-
ing outside line call.
You must be in the same pickup group.410.19 PLACING CALLS ON EXCLUSIVE
HOLD
While connected to an outside line:
a. Briefly press and release the hookswitch.(Call is placed on Exclusive Hold).
To retrieve the call:
a. Press and release the hookswitch again.410.20 HANDSET RECEIVER GAIN
This feature allows an SLT user to increase/de-crease the handset volume while on a CO or
intercom call.
While on a CO or intercom call:a. Hookflash and dial the Handset Receiver
Gain code 
[638] on the dial pad.
b. Dial a one-digit entry [0] through [9] on the
(O=lowest, 
9=highest) on the dial pad,or
Press the [#I to increase or [?k] to decrease
the gain, one level at a time.
c. Hookflash again to return to call.
d. Repeat above procedures, if necessary.
e. Replace the handset to end the call.410.21 INTERCOM CALLING
a. You will hear ringing if called station is inthe ‘TN” answering mode; or two bursts of
tone if called station is in the 
“HP” or “PV
position.
b. Lift the handset.
c. Dial the three-digit intercom number:
-1 OO- 195 for infinite DVX ‘I1 System
d. Converse after the two tone bursts stop.
e. Replace the handset to end the call.
Answering an Intercom Call
a. Lift handset to converse.
b. Replace handset to end call410.22 LEAST COST ROUTING
To place an outside call when LCR has been
enabled in the system:
a. Lift the handset.b. Dial 
[9] on the dial pad.
c. Dial the desired seven-digit telephone
number (i.e.: 
l+ area code+7-digit num-
ber).
d. Wait for an answer, then converse.If all lines available to you are busy, remain
off-hook for four seconds to automatically be
queued onto LCR for an available line.
If an LCR Queue Callback has been activated:a. When telephone is signaled, answer the
Call.b. Desired telephone number will automat-
ically be re-dialed.
Only one LCR Queue Call Back request maybe initiated by CL station. When a second
request is made, the first request is
cance&d. >;If an LCR Queue Callback has been activated
and you wish to cancel that callback request:
a. Dial the LCR Queue Cancel code, 
[626] onthe dial pad.
b. Replace the handset.410.23 MESSAGE WAITING
Leaving a Message Waiting Indication
a. Lift handset.
b. Dial the desired intercom station. Receive
no answer, or DND tone.c. Briefly depress and release the 
hook-
switch.d. Dial 
[623] on the dial pad.
e. Replace handset.410-6
Issue 1, February 1994 
						

							infinitem DVX I’Digital Key Telephone System
SLT FEATURE OPERATION
Answering a Message Waiting Indication.
Your message waiting lamp is flashing:
a. Lift handset.
b. Dial 
[663] on the dial pad. Station that left
the message will ring.
Only SLT’s equipped with message waiting
lamp will have access to this feature. Opxstations do not have message waiting
capability.
410.24 OFF-HOOK PREFERENCE
If your phone has been programmed for 
Off-
Hook Preference, you will hear outside line dial
tone when lifting the handset.When this operation is enabled, you may not
have access to all features contained in this
User Guide. However, consult your 
Centrex or
PBX User’s Guide for additional features you
may have.410.25 PERSONALIZED MESSAGES
Each station can select a pre-assigned messageto be displayed on the LCD of any Key Tele-
phone calling that station. To select one of the
ten available messages:a. Dial 
[633] on the dial pad.
b.Dial the two-digit code for the message
which will appear.
- [00] = clears message
- [Ol] = ONVACATION
- [02]=RETURNAM
- [03] = RETURN PM
- [04]= RETURN TOMORROW
- [05] = RETURN NEXTWEEK
- [06] = ON TRIP
- [07] = IN MEETING
- [08] = AT HOME
- [09] = ON BREAK
- [lo] = AT LUNCHwThis featureisnot 
avaiZabZetothe
c. Replace the handset. (Activating DND or
Call Forwarding cancels selected mes-
sage.)410.26 PAGING
a. Lift handset.b.Dial the two-digit paging code. Wait for
page warning tone
- [70] = All Call - Internal & External
- [71] = Internal Zone 1
- [72] = Internal Zone 2
- [73] = Internal Zone 3
- 1741 = Internal Zone 4
- [75] = Internal All Call
-[76 ] (0) = External All Call (All Ext Zones)
- [76 l(Z) = External Zone l-7
c. Speak in normal tone of voice to deliver
message.Stations off-hook or in DND will not hear the
internal page announcement.When making a Zone Page OF 
AZ1 CaZZ Page
and the zone is busy, the page initiator wiZZreceive rincrback tone until the zone 1
~announ&ment .
becomes av&bZe. You will then hear a
warning tone and can make the page
- - j
d. Deliver page in normal tone of voice.
e. Replace handset to terminate page.410.27 MEET 
MI3 PAGE
To request another party to meet you on a page:a. Dial the desired two-digit or three-digit
paging code.
b. Request that party meet you on the page.c. Do not hang up; wait for the requested
party to answer. As soon as the paged party
answers and is connected to you, the page
circuit is released.
Answering a Meet Me Pagea. Go to the nearest telephone and dial 
[77]on the dial pad. You will be connected to
the party that paged you.
410.28 PERSONAL PARK (Flip-Flop)
While connected to first call:
a. Depress the hookswitch momentarily. In-
tercom dial tone is heard.
b. Dial 
[438] on the dial pad. (call is placed in
personal park).
c. Dial desired number for 2nd call.
d. Depress the hookswitch momentarily. In-
tercom dial tone is heard.e. Dial 
[438] on the dial pad. (1st call is re-
turned and 2nd call is placed in personal
park.The 
ussr can alternately connect to theother call by doing a hwksash and diaZing[438] as many times as necessary.
410.29 PROGRAMMING YOUR NAME
INTO THE LCD DISPLAY
Every SLT extension has the capability to pro-
gram the users name so that people using dis-
play telephones will see the name instead of the
station number.
a. Lift handset.Issue 1, February 1994
410-7