Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

							infinite TM Diiieal SystemsTF NO: 58
Tl TN& Card (CotWd)
Program Button # 2:
Prints out the attributes of each line in the 
Tl channel bank.
1.Press the CO line attribute flexible Button (Button # 2). The following message displays on the phone LCD:
2.Once the system sends information to the printer, the following is a sample report:CO LINE 
ATTkIBUTES
------------------
co 01
-----
LINE 01
SIGNAL TYPE UNA CONF PRIDTMF CO YY Y
SUPV DISA FLTM GRP COS DIR RDNN
lo 113 0
SIG RING DIAL VOL2Y Y7
RING ASSIGNMENTS100B
Page 45 of 46TF NO. 58
83allLkmw~&dbd&RE526uWW~ooO 
						

							PRODUCT NOTICE
PN0023
infinite Digital Systems
October 27,1995AFFECTED PRODUCTS:
SUBJECT:
UPDATES:
1.
2.
4
b)
cl-
d)
Software Version 3.1 jDVX I, DVX II, and DVX 
III Systems
S/w Release for DVX Systems
A change in administration programming has been 
add,ed to SNV version 3.lj and
above. This change is as follows:
On DVX I & DVX ii systems the station ID programming (Page B, button 1) hasbeen changed. Station ID 7 now reflects a relay/sensor box and Station ID 8
now reflects a 
DDIU unit. The complete station ID map for all DVX digital
systems is now:
[0] = 
ID0 Digital
[l] = ID1 DSS Map 1
[2] = ID2 DSS Map 2
[3] = ID3 DSS Map 3 (DVX III only)
[4] = ID4 DSS Map 4 (DVX III only)
[5] = ID5 SLT/OPX
[6] = ID6 SLT wl MSG
[7] = ID7 Relay/Sensor Box
[8] = ID8 DDIU Unit
[9] = ID9 DSS Map 5 (DVX III only)
In addition to the above programming change, the following information applies to
S/W version 3.1 j and above:The forward override code 
(5#) will allow an OHVO function to be performed at a
busy station that is busy forwarded.
The 300 baud rate function of the PC Interface mode (648) is not supported. Always
select 1200, 2400, or 4800 baud. Do not utilize 300 baud.
Camp on ringing to a station cannot be picked up via directed call pickup. The
current technical manual states that this can be done. (Page 400.18, Directed Call
Pickup)The CO transmit volume option will not function unless the handset receiver gain
option is enabled. The handset receiver gain option is programmed in FLASH 05,
BUTTON 13.
Page 1 of 3Vodavi Communications Systems
8300 E. 
Raintree DriveScottsdale, AZ 85260(602) 443-6000 
						

							PRODUCT NOTICEINFINITE DIGITAL SYSTEMS
PN00234Issue 2 of the Technical Manual inadvertently left out information regarding the RAN
Hunt Group feature that was added to FP3 software. This enhancement allows an
ACD RAN to be directed 
+o a hunt group to permit up to eight (8) callers to receive
the RAN announcement at a time. There can be up to four (4) RAN hunt groups in
the system.Programming hunt groups:
1.At station 100, dial **3226.
2.Press the FLASH button and dial 30.
3.The button layout for Hunt Group programming is now as follows:
Entering hunt groups in announcement tables:
1.At station 100, dial ‘*3226.
2.Press the FLASH button and dial 62.
3.Enter the desired string of digits using the keypad. The order entry
is:TYPE NUMBER
[llco Port
PISLT Port
[31Hunt Group
INDEX NUMBER
[Ol-961CO Line
[loo-3151Station Number
[458-4611Hunt Group
Page 2 of 3Vodavi Communications Systems
8300 E. Raintree DriveScottsdale, AZ 85260(602) 443-6000 
						

							PRODUCT NOTICE
INFINITE DIGITAL SYSTEMS
PN0023
Conditions:1.
2.
3.
4.
5.RAN hunt group pilot numbers are 458-461.
RAN hunt group numbers can be chained together by placing theRAN group number (458-461) as the last member in the desired
group.
Hunt group pilot numbers 458-461 are reserved exclusively for RANfunctions. Both guaranteed and regular RAN announcements can
be directed to a RAN hunt group.
Both guaranteed and regular RAN announcements can be directed
to a RAN hunt group.
4RAN hunt groups are pilot type only and cannot be changed. Only
SLT stations can be entered into these type of hunt groups.
f)A comprehensive RAM test has been added to the software. If this RAM test fails.
the red heartbeat LED will flash rapidly. If this rapid flashing continues for more than
5 minutes, the RAM test has failed,
If the RAM test fails, the problem is in the DVX I Basic KSU, DVX II CPU, or the DVXIII CPU/Memory Expansion Kit. On the DVX 
III, verify the following:
Check the seating of the memory expansion kit if installed.
If the memory expansion kit is installed, check that jumper J4 is installed
between 
Dins 1 & 2.
9)Software 3.lj now supports disconnect supervision for ground start emulation of Tlcircuits. This was not available in previous versions of software. Disconnect
supervision is not supported for loop start emulation of 
Tl circuits.
Page 3 of 3Vodavi Communications Systems
8300 E. Raintree DriveScottsdale, AZ 85260(602) 443-6000 
						

							INPN0032infinite Digital Systems
October 1997
Revision B
Software Version-3.4 SeriesAFFECTED PRODUCTS:DVX I, DVX II, DVX 
Ill Systems
SUBJECT:
UPDATES:New Software Release for infinite Digital Systems
1.Please note that when the System Speed Dial and Directory Dial areas are
initialized, Station Speed bins will be initialized.
2.A correction was made to allow a Group Pickup buttonlfhat was programmed in
Administration to be used with Directed Call Pickup and be programmed at the
station level.
3.The software will correctly
adjust the year on the LCD and SMDR printout to 00 when the year 2000 is reached. Prior versions showed the yearas 
A0 on the LCD for 24 hours before properly updating to 00. Prior versions also printed out the year as 000 for 24
hours before properly updating to 00.
4.Caller ID information will now be presented on the LCD when utilizing the Call Pickupfeature. In previous versions the Call Pickup message would be displayed in place
of the Caller ID information.
5.Several new programming areas have been added to aid in connecting multiple
Infinite Digital Systems together via TIE trunks or 
Tl trunks. These areas are:
Leading Digit Translation
Four Digit Numbering
Centrex DigitsThese features will allow multiple systems to easily communicate via a four digit
numbering plan. In the case of 2 systems (System A and System B), System A
station numbers could be 1000 series and System B station numbers could be 2000series. A System A user wishing to dial a System B user would simply dial the
desired 2000 series station number. The call would then route over the TIE trunk to
the desired destination station.
Vodavi Communications SystemsPage 1 of 6
8300 E. Raintree DriveScottsdale, AZ.. 85260(602) 443-6000 
						

							PRODUCT NOTICEINFINITE DIGITAL SYSTEMS
INPN0032
PROGRAMMING LEADING DIGITS:
This feature provides the ability for the system to have the dialing plan modified to
accommodate multiple systems connected via TIE/T1 trunks. The dialing plan is
changed to a four digit access with a programmable leading digit. All Feature AccessCodes (except those starting with 8, 9, or 0) and Station Numbers will be dialed by
dialing the programmable leading digit first followed by the standard dialing plan.
Enter Programming mode and to
goFLASH 09,Button 1thru 7. Button1representsdigit 
1, Button 2 digit 2 etc. throughdigit 7. TheLCD willindicate:
Enter a one digit entry on the keypad O-8.
0=NONE3=TrunkGroup3(83)6=Trunk Group 6(86)
1=Trunk Group1(81)4=TrunkGroup4(84)7=Trunk Group 7(87)
2=Trunk Group2(82)5=TrunkGroup5(85)8=Leading Digit*
* 8 is not available on Button 7 (digit 7), only O-7 are available on Button 7.
Press the HOLD button to save the entry. Confirmation tone will be heard and the
LCD will indicate the change.
CONDITIONS:
The leading digit does not apply to Feature Access Codes starting with 8, 9, or 0.
The remaining digits for the Infinite system may be used as CO Line Group Accessfor 
Centrex dialing applications.
PROGRAMMING THE LEADING DIGIT OPTION:
This feature will enable/disable the Leading digit Integration feature
option on a system wide basis.Enter Programming mode and go to FLASH 09, Button 8. The LCD will display:
Enter a 0 or 1 on the keypad: 0 
= disable 1 = enable
Press the HOLD button to save the entry, Confirmation tone will be heard and the
LCD will indicate the change.
Page 2 of 6
Vodavi Communications Systems8300 E. 
Raintree DriveScottsdale, AZ.. 85260(602) 443-6000 
						

							PRODUCT NOTICEINFINITE DIGITAL SYSTEMS
INPN0032
CONDITIONS:
This feature is disabled by default.
PROGRAMMING THE LENGTH OF CENTREX DIGITS:
This feature determines the length of 
centrex digits in the system. When a leading
digit marked as Trunk Group Access is dialed, the remaining 3 or 4 digits will be
collected and the system will access the desired trunk group and outpulse the digits.This program determines when the end of dial is by the amount of digits dialed.
Enter programming mode and go to FLASH 09, Button 9. The LCD will display:
Enter a 4 or 5 on the keypad:aPress the HOLD button to save the entry. Confirmation tone will be heard and the
LCD will indicate the change.CONDITIONS:
The default value is 4 digits.
Vodavi Communications Systems
8300 E. Raintree DriveScottsdale, AZ.. 85260 
						

							PRODUCT NOTICEINFINITE DIGITAL SYSTEMS
INPN00326.Caller ID Name and Number Display
A new feature has been added to allow a station user to program a flexible button
to enable the user to view both the number and name on the LCD when receiving
a Caller ID CO call. The top line of the LCD will display the number of the caller and
the bottom line of the LCD will display the name.
The user must program a Flexible Button onto their telephone. SPEED + SPEED +
FLEX + 653.If the feature is enabled, LED lit solid, the name and number will be displayed.
During the call, the user can press the flexible button to view the normal call
information.
CONDITIONS:
1.When enabled, this display will override transfer call LCD messages, ACD
Ring messages, Call Pickup messages, and Ansrer messages. If the user
wishes to view the Line Number/Call Timer and the standard call informationthey can press the flexible button to toggle between the name number and
normal mode.
2.By default no button is assigned on telephones.
3.The printout of the Station Button will indicate CID as the button designationfor this type of flexible button.
4.The number and name will be formatted on the LCD in he same manner as
the current caller ID display.
7.Four Digit Voice Mail ID Enhancement
This feature modifies the station and CO Voice Mail identification fields such that themaximum length of these fields is increased from 3 digits to 4 digits.
OPERATION
The entry in FLASH 50, PAGE B, BUTTON 12 shall accept up to a four digit
entry. These digits can be O-9.The entry in FLASH 40, PAGE B, BUTTON 6 shall accept up to a four digit
entry. These digits can be O-9.The 256 entries in FLASH 68 shall accept up to a four digit entry. These
digits can be O-9.CONDITIONS
This feature applies to S/W Versions 3.41 and above on the DVX
III digital systems.I, II, and
Page 5 of 6
Vodavi Communications Systems8300 E. 
Raintree DriveScottsdale, AZ.. 85260(602) 443-6000 
						

							-*.PRODUCT NOTICE
INFINITE DIGITAL SYSTEMS
INPN0032
PROGRAMMING:
1.FLASH 09 Button 10123456789012345678901234
~
2.Enter a 3 or 4 on the keypad.
3.Press HOLD
8.Direct CO Access
This feature modifies the way digits are dialed when CO senderization is enabled inthe system. If senderization is enabled in the system, 
thd’system will wait for the
length of the pause timer before sending the first dialed digit. The system will accept
digits from the station as rapidly as the station dials. This applies to direct line accessvia a CO button or line access via a trunk group access code.
9.Initialization EnhancementThis feature modifies the way the memory correction function operates. In previous
versions of software, if the system detected any contamination of the memory it
would default the database to correct the contamination. This feature allows the
administrator to choose if the software will initialize the system or simply report a
contamination error.
PROGRAMMING:
1.FLASH 06 Button 11123456789012345678901234
2.Enter a 0 or 1 on the keypad. (DISABLE/ENABLE)
3.Press HOLDThe first four digits represent specific areas of the memory. A 0 indicates the
memory area has no contamination, a 
1 indicates the area has contamination. The
areas are as follows:
First digit =
Second digit =Third digit 
=Fourth digit 
=
Station areaCO area
LCR and Toll areas
ICLID and SystemPage 6 of 6
Vodavi Communications Systems
8300 E. 
Raintree DriveScottsdale. AZ.. 85260(602) 443-6000 
						

							PRODUCT NOTICEINFINITE DIGITAL SYSTEMS
INPN0032
Station 1100
System A
Trunk Group
connected tcSystem B
Dial 1100 Dial 2101System 
6Trunk Group
connected to
System AStation 2100
Station 
2101
AEXAMPLE APPLICATION:
System A connected to System B via TIE trunks.Program the leading digit 1 (FLASH 09 Button 
1, dial 8 on the keypad) to be a leading digit on System A.
Program the leading digit 
2(FLASH 09 Button 2, dial 8 on the keypad) to be a leading digit on System B.
Enable the leading digit option on System A and System 
B(FLASH 09 Button 8, dial 1 on the keypad).
Program the leading digit 
2(FLASH 09 Button 2, dial l-7 on the keypad) on System A to be the trunk group
access to System B. Enter the Trunk Group (l-7) that the TIE trunks connected to System B are programmed
in.Program the leading digit 1 (FLASH 09 Button 
1, dial l-7 on the keypad) on System B to be the trunk group
access to System A. Enter the Trunk Group (l-7) that the TIE trunks connected to System A are programmed
in.
Page 4 of 6Vodavi Communications Systems6300 E. 
Raintree DriveScottsdale, AZ.. 85260(602) 443-6000