Home
>
Vodavi
>
Communications System
>
Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual
Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual
Have a look at the manual Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 60 Vodavi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 136
infinite TM Digiil SystemsTF NO: 58
Tl Tndc Card (Cti’d)
Tl Charnel Charactehstii:
Once the Tl is assigned to a slot, assign each Tl line (channel) or a range of lines individual characteristics.
There are two sets of assignments to the buttons in the FLASH 40 programming mode, Page A and Page B.
1.Press the FLASH button and dial [40]. The LCD displays the following:
2.Use the dial pad to enter a four-digit number for the range of Tl lines to program. The possible range
for these lines is 01-96. If only...](http://img.usermanuals.tech/thumb/5735/86551/w64_vodavi-infinite-dvx-iii-installation_d-135.png "Page 136
infinite TM Digiil SystemsTF NO: 58
Tl Tndc Card (Cti’d)
Tl Charnel Charactehstii:
Once the Tl is assigned to a slot, assign each Tl line (channel) or a range of lines individual characteristics.
There are two sets of assignments to the buttons in the FLASH 40 programming mode, Page A and Page B.
1.Press the FLASH button and dial [40]. The LCD displays the following:
2.Use the dial pad to enter a four-digit number for the range of Tl lines to program. The possible range
for these lines is 01-96. If only...")
![Page 138
infinife TM Digiil SystemsTF NO: 58
Tl Trunk Card (Cont’d)
3.Press the HOLD button. A confirmation tone is heard and the LCD display is updated. Default = LOOP
Start
For example: Entering
[7j on the dial pad produces:
To Program the Ringhck Option
1.Press the RINGBACK Button (Button #Q) toenable or disable a range of Tl spans. To program the
option enter
[l] on the dial pad to enable or [0] to disable the Ringback.The following message
displays on the LCD:
Where:
XX-XX= the range of CO lines (01-96)
O-l...](http://img.usermanuals.tech/thumb/5735/86551/w64_vodavi-infinite-dvx-iii-installation_d-137.png "Page 138
infinife TM Digiil SystemsTF NO: 58
Tl Trunk Card (Cont’d)
3.Press the HOLD button. A confirmation tone is heard and the LCD display is updated. Default = LOOP
Start
For example: Entering
[7j on the dial pad produces:
To Program the Ringhck Option
1.Press the RINGBACK Button (Button #Q) toenable or disable a range of Tl spans. To program the
option enter
[l] on the dial pad to enable or [0] to disable the Ringback.The following message
displays on the LCD:
Where:
XX-XX= the range of CO lines (01-96)
O-l...")
intinite TM Digiil SystemsTF NO: 58 Tl Trunk Card (Cont’d) (Fmnl INDCATIONS(Circuit Board)I Panel)-- RS232cCOllflWdbn(ml used with T-SEW IQNETWORKCorm&on (Rear Paler)EQUIPMENT FRAh4EPOWERConnecrionGROUNDSlud Figure 5 Channel Service Unit (CSU) Setup Page 24 of 46TF NO. 58
infinite m Diiital SystemsTF NO: 58 Tl Trunk Card (Cti’d) Telephone Company (Caer ) Lhs Power 1.Be sure the power jumper is set to the LINE position. 2.Connect a ground wire to either the Power terminal plug (Post 4) or to the frame ground stud on the rear of the CSU. (Do not use both at once) This is the only connection needed for the Line Power Option. WARNING..:...:.:.:...:..:.,. ,..:>:.:.:.:.: ::. .:....:: :. .:..I jj:, ,:.::.:.:: . . . . . .:.:.:..... :. :y;.,: ::,j:y.$+j& . . “ii.- Tl spa” is pia & #&g&i Og&u&&)US M= c&5(+ j3hi~~~‘E_(:;:i- ,::,,, j 130~) are psenl on the TELCO s#e of the CSU..l ‘, ::‘:.. 1 ...!.y:,:, ,.. :y:.::..:~.~ 1:‘:.. .: :-I::~-_-‘,:li,i:r,l,:~:i:.::~::: ‘. .: ..’.’”“.:::.. :y;: . . . . . . . ‘:.::..,:;.:::...: ;,. : . . . . . :,.: :.. . . . :(Rear Panel)’ FRAME Ground ALARM outputs (optional)FRAME Ground\ Page 25 of 46TF NO. 58 83ooLRmmIkivetkcomk&R65260lW=m
infinite m Diiital SystemsTF NO: 58 Tl Tank Card (Cont’d) Local Power 1. 2.Be sure the power jumper is set to the LOCAL position. The Tl Digital Trunk Card kit contains a power transformer to convert AC power to the 48 volt DC power supply required for the CSU. Using 20 gauge leads or larger, wire power to the six-post terminal plug and install the plug in to the rear panel. Connect Pin l- Battery Return (V+) and Pin 3- Battery (v-) to the transformer. NOTE: Usa either Post 4 of the power plug or the Frame ground stud for Frameground, BUT NOT BOTH.FRAME Ground outputs(optional) Pl Page 26 of 46TF NO. 58 83alE.Rarmmescclw&#R~6uWW-Qloo
infinite TM Digiil SystemsTF NO: 58 Tl Tfurk Card (Cont’d) I Line Bui#Out Options Proper setting of the Line Build-out switches is used to compensate for loss between the last repeater and the CSU. Set the Line Build-out switches using the following table.Distance from Repeater \Settha Maximum or if unit is connected to a smart jack or other network maintenance device Not Known or not specifiedO.OdB a -7.5dB Minimum Not Used -15.OdB -225dB Internal Switch Settbgs An 8position DIP switch S.300, controls the following operational modes of the CSU. The switch is at the side of the board. Use a small screwdriver to set the switches. The following table lists the switch settings. SWitCllIFunction On Positionoff PositiiIII SW#lLoopbackLineloop*TestloopI ISW#2Pulse Stuffing!Stuff after 47sStuff after 15.II SW#3ORSSNo logic error*Per AT&T 624111 SW#4Pulse Density SW#5Keep AliveSW # 6,7,8Not Used l Default posrtion set at factory.Disables Unframed*Enables l FramedPage 27 of 46TF NO. 58
infinite m Digital SystemsTF NO: 58 Tl Tnrnk Card (Cont’d) 4.CONNECTING THE CSU TO THE Tl CIRCUIT When the options have been set and the TI type and Line fype have been programmed for each Tl channel, slidethe stand-alone card into the card guides of the mounting shell. Secure the card in position with the screws provided. Connect the system to the Tl circuit. 1.Connect the CSU to the Network interface through the NETWORK connecto$ (P2). Plug the 15pin connector on the cable provided into the P2 connector on the CSU board. Plug the 8-pin RJ-48X Connector on the other end of this cable to connect to the Tl line.L 2.Connect the CSU to the infinite DVX illDigital System using the Equipment connector (J4) on the rear of the CSU. If all connections have been made, and the Tl trunk is active, check the front panel of the Tl trunk card. The Test Mode LED should flash at a one second rate. The Receive Carrier Loss LCD (DS2) should be off. Page 28 of 46TF NO. 58 63alLniMmMuesamd&R65260ww443-~
a ,~a RJ-48XNetwork Interface 7rEmpty cards slot to the left of the Tl tplnk cardTl trunk cards\\I\Wire Jl to P3 on Tl trunk cardRIReceive clodc recovery11cable connections to show Jl - Equipment sideconnecting points - notactual routing of receivedock recovery cable csu [+d52 - Network side, Test connections and LEDs48 volt DC power supply Connect to AC source Figure 6 Tl Trunk Card Setup Page 29 of 46TF NO. 58 WaviCommuJealbm Systems
&iWfe TM Digiil Systems Trunk Card (Cant’d) 3.installing the Adtran Channel Service Unit (CSU) and connect it to the trunk card. TF NO: 58 The stand-alone Channel Service Unit (CSU) provided in the Tl kit can be mounted on a desk or on the wall. Mounting instructions are provided. Before mounting the CSU, a number of options need to be checked and set. To perform the installation: 1. 2. 3. 4. 5. Set Line Build-Out Options. Connect to the Carrier and Customer Premise Equipment (CPE). Connect power (if not from Carrier). Understand additional features of the ADTRAN CSU. Mount on wall bracket. \ Use the diagram below to help set options. Be we that each chafne#s 75 m and .ti.Qpct Zs~defbwd NOTEhsyslempmgmmmhgbefci&contbuhgw&hfhe hstam Page 30 of 46TF NO. 58 83alLlwltreelmsamdb+R65260WI-~
infinite TM Digital SystemsTF NO: 58 Tl Tnrnk Card (Cont’d)Step 1. Set Line BuiI&Out Options Set the Line Build-out switches to compensate for loss between the last repeater and the CSU. The five-position switch on the front of the CSU selects Line Build Out (LBO) Separate LBOs set the transmit levels for the Network and CPE sides of the CSU. Receivers on both sides of the CSU contain Automatic Line Build Out circuitry to compensate for loss of signal (LOS) from the network. Set the Line Build-out switches using the following tables: Table 1. Netwo& LB0 Switch Position Settbgs IONIOFFj-7.5dBIa OFFON-15.0dB OFFOFF -22.548 i Table 2. Customer LB0 Switch Positii SetthgsPOSITION 4 OFF ONPOSITION 5 ON OFF CABLELENGTH FEET) o-1 33 134-266 ON.QF.F ’267-399 OFF OFF 400533 - o‘Fi’“‘.: . ”OFF534-655 Recommended Settings Position 1ONPosition 2 ON Position 3OFF Position 4OFFPosition 5 ON Which is equivalent to 0 (dB) attenuation and a cable length of O-133 feet.Page 31 of 46TF NO. 58 8300LiwltmRk~Rw260(=I-~
infinite TM Digital SystemsTF NO: 58 Tl TN& Card (Cont’d) Step 2. Comection to the Network and Customer Premise Equ@ment (CPE) Two RJ48 modular connectors are located on the bottom of the CSU.First connect modular connector labeled “NET” to the Network using the Network cable. Then connect the “CPE” from the CSU to the Tl in the DVX ill. Se sure to connect the CSU to the Network demarcation before connecting to the infinite DVX ‘nfiniteIll. Step 3. Powerhg Options The ADTRAN CSU kit contains an external power adaptor. Always use this adaptor in all ipstallations.The power connection is located on the bottom of the CSU. Adtmn CSU Power Connections This end attaches to customer power This end plugs into the CSUPage 32 of 46TF NO. 58 8aooLRiMmDlhafftrblakR6lJ(w-~
hlfnite JM Digital SystemsTF NO: 58 Tl Trunk Card (Cord’d)infinite DVX ” Digital System Adtran Connections “:,:,:::::.:::,:‘:.:::::::.,:.:::::~cable connections toshow connecting points Figure 9 Adtran Tl Connection Page 33 of 46TF NO. 58