Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

							REMOTE ADMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
TABLE RM-AW 
PROGRAM 55-O 
LCR MODIFIED DIGITS-DELETE . 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter B m B 1 
q . P 
2 Enter Program Number 55 P 55 
Press 
q P55 
3 Enter Modified Digits Table Number P55 1 
Refer to the System Record Sheet and enter the modified 
digits table number (1 - 6). 
Example: Enter modified digits table number 1, entern . 
4 Enter Code 0 P55 10 00 10 
The system will display any previously entered number of 
digits to be deleted (01 - 10). 
Refer to the System Record Sheet and change number if required. 
Example: Change to 10, enter:0 1. 
5 
To Exit Program/Store Data P55 10 00 10 
A) To store data, press 
q . 
P55 ## 
B) Continue returning to step 3 until all data has been entered 
P 
for this program. 
C) To exit this program, press @ 1 
q . ‘: 
-46-  
						

							REMOTEADMIN &MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AX 
PROGRAM55-1 
LCR MODIFIED DIGITS-ADD 
;TEP ACTION 
DISPLAY/PRINTOUT 
I Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter i m m a 
q . P 
2 Enter Program Number 55 P 55 
Press 
q . P55 
3 Enter Modified Digits Table Number P55 1 
Refer to the System Record Sheet and enter the required 
modified digits table number (1 - 6). 
Example: Enter table number 1, enter [ . 
4 Enter Code 1 P55 11~~~ (up to22 digits) 
The system will display any previously entered digits (up to 22). 1234P3 
Refer to the System Record Sheet and enter new numbers, 
if required. 
Example: Enter~~~~~~ . 
NOTE: Pause codes may also be entered. To enter pauses, 
press “P” plus the pause number (1 - 8). 
Special Code Input 
Pause = 11% iI. 
Tone = 0 at beginning of digits to convert. 
Clear = 1 as first digit, then 
q . 
5 
To Exit Program/Store Data P55 11mIl 
A) To store data, press 
q 1234P3 
B) Continue returning to step 3 until all data has been entered 
P55 ## 
for this program. P 
C) To exit this program, press 1 1 
q . 
-47-  
						

							REMOTEAOMIN & MAINTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AY 
PROGRAM 55-2 
LCR MODIFIED DIGITS-END 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter B H B 1 
q P 
2 Enter Program Number 55 P 55 
Press 
q . P55 
3 Enter Modified Digits Table Number P55 1 
Refer to the System Record Sheet and enter the required 
modified digits table number (1 - 6). 
Example: Enter table number 1, enter 0. 
4 Enter Code 2 p55 12 nnn (up fo22digifs) 
The system will display any previously entered digits (up to 22). 1234P3 
Refer to the System Record Sheet and enter new numbers, 
if required. 
Example: Enter 1 u 11 i m . 
NOTE: Pause codes may also be entered. To enter pauses, 
press “P”plus the pause number (I - 8). 
Special Code Input 
Pause = Na - NB 
Tone = 0 at beginning of digits to convert. 
Clear = m as first digit, then 
q 
5 To Exit Program/Store Data P55 12 otlotl (up to 22digits) 
A) To store data, press [9 . 
1234P3 
9) Continue returning to step 3 until all data has been entered 
P55 ## 
for this program. 
P 
C) To exit this program, press4 1 
q 
-4B-  
						

							REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AZ 
PROGRAM56 
LCRSTATIONGROUPASSIGNMENT 
STEP1 ACTION 
I DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the z-MODE prompt, enter w a 1 H 
q . P 
2 Enter Program Number 56 P 56 
Press (9 P56 
3 
Enter Port Number 
4 
Refer to the System Record Sheet and enter the 
required port number, [70 or 00 Ino. 
Example: Port 01, enter 1 0. 
Press OKey (if single port 00 entry in step 3). 
The system will display any previously entered group number (1 - 4). 
Refer to the System Record Sheet and change as required. 
Example: Change to 4, enter1 . P56 01 
P56 01# 1 4 
5 To Exit Program/Store Data 
A) To store data, press q . 
B) Continue returning to step 3 until all data has been entered 
for this program. 
C) To exit this program, press1 1 
q . P56 Ol# 1 4 
P56 ## 
P 
-49-  
						

							REMOTE ADMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
TABLE RM-BA 
PROGRAM DATA DUMP 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Data Dump Mode >MODE DUMP 
At the >MODE prompt, enter 1 m m 1 
q . D 
2 
To Output Program Data 
Enter 1 g Inn q 
D PROGun 
00 = Program number or 110 for all programs. 
3 
I I 
To Stop Printout at Any Time 
Enter JrRr=ll$m . 
TABLE RM-BB 
SPEED DIALING DATA DUMP 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Data Dump Mode 
>MODE DUMP 
At the >MODE prompt, enter 1 1 1 a 
q . 
D 
2 
To Output Speed Dialing Data 
Enter B a 1 nnn [9 ---or--- 1 0 4 00 q 
UOU =MO or 811 
00 = Port number for individual station speed dial. 
3 
To Stop Printout at Any Time D 
Enter mm . 
-5o-  
						

							REMOTEAOMIN &MAlNTPROCEDURES 
SECTlOti200-096-600 
FEBRUARY1991 
TABLERM-BC 
LCOMESSAGING DATADUMP 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Data Dump Mode 
>MODE DUMP 
At the >MODE prompt, enter m 1 m i 
q . 
* 
To Output Message Data 
D MSGnuu 
Enter @ H H nnn q ---or--- m 1 100 q 
mo =m or 8i8 
00 = Pot-t number of individual station. 
3 
I / 
To Stop Printout at Any Time D 
Enter mm 
I 
-51-  
						

							REMOTE AOMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
TABLE RM-BD 
MODE 95 
REMOTE CALLING STATION MESSAGING (ADD/REVIEW/CHANGE) . 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Message Mode >MODE MESG 
At the >MODE prompt, enter m 0 1 a 
q . 
2 
To Add Or Review a Calling Station Message m 95 
Set the terminal keyboard to the lower case (cap lock off) and 
enter QII. 
NOTE: 
Enter “m” anytime it is desired to start over in this procedure. 
3 Enter 1 1 1 (XXX = station number where the message will be m95 XXX 
set and stored). 
4 Enter B [7(7 (p = page command and 
m95 xxx ~017 
[Ml 00 = 2-digit message memory location: IO - 19 personal 
messages and 60 = 99 = system message). 
NOTES: 
1. To store system messages permanently, EKT XXX must be the 
station at port 00. 
2. After 1 00 IS entered, the previously stored message is 
displayed. If there is no stored message, nothing is displayed. 
5 To Change Previous Message 
m95 xxx ~00 W+l Set the terminal keyboard to upper case and change message 
(alphanumeric, 32 characters max.). 
6 To Set the Message on EKT XXX’s LCD 
Set the terminal keyboard to lower case and enter BmI . 
m95 XXX p mo[M+] p 
m0 
-L Zero 
7 To Exit the Message Mode m0 
At any time, enter 111 (lower case). 
9 
> MODE 
NOTES: 
I. To cancel a message set via Mode 95, use Mode 97 procedure. 
2. [M] represents the message entered. 
3. With 
Release 2 software only, remote calling station messaging is not available from electronic 
telephones, but it is available from ASCII terminals connected to the TTYport or via IMDU on the 
PIOU or PIOUS. 
-52-  
						

							REMOTEADMlN&MAlNTPROCEDURES 
SECTlON200-096-600 
FEBRUARY1991 
TABLERM-BE 
MODE97 
REMOTECALLINGSTATION MESSAGlNG(ADD/CHANGE) 
TEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Message Mode 
>MODE MESG 
At the >MODE prompt, enter m 0 lI[9 
. 
2 
To Add a Message (or change a previously stored message) 
m 97 
Set the terminal keyboard to lower case (caps lock off) and 
enter 110 
NOTE: 
Enter I’m” at anytime it is desired to start over in this procedure. 
3 Enter 1 1 0(XxX = station number for which the message will m97 XXX 
be set and stored). 
4 Enter: 1 00 (p = page command and 
170 = 2-digit message memory location: IO * 19 personal m97 XXX p 00 
messages and 60 w 99 = system messages). 
NOTE: 
To store system message change permanently, EKT XXX must be 
station assigned to port 00. 
5 To Add a Message 
m97 XXX P 00 [Ml Set the terminal keyboard to upper case and enter message 
(alphanumeric, 32 characters max.). New message displays as 
it is entered. 
6 To Set the Message on the Electronic Telephone’s LCD 
Set the terminal keyboard to lower case and enter 1 m 1 m97 XXX P 00 WI P 
m JL Zero 
7 To Exit the Message Mode m0 
At any time, enter 1 b 1 (lower case). 
q 
>MODE 
NOTES: 
1. To cancel a message set via Mode 95, use Mode 97 with any message number in step 4, use this 
procedure and skip step 5. 
2. [M] represents the message entered. 
3. With Release 2 software only, remote calling station messaging is not available from electronic 
telephones, but it is available from ASCII terminals connected to the TTY port or via IMDU on the 
PIOU or PIOUS. 
-53-  
						

							REMOTE AOMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
TABLE RM-BF 
MODE 94 
REMOTE CALLED STATION MESSAGING (ADD/REVIEW/CHANGE) . 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Message Mode >MODE MFSG 
At the >MODE prompt, enter m 0 1 H [9 . 
2 
To Add Or Review a Called Station Message m 94 
Set the terminal keyboard to the lower case (cap lock off) and 
enter min. 
3 Enter 0 1 0(XxX = Destination station number or destination m94 xxx 
group number [30 = all stations, 31-34 per system, 
Program 311). 
4 Enter 11 m 1 (p = page command [lower case] and 
1 u 13 = originating station number). m94 XXX p YYY 
5 Enter Ino (p = page command [lower case] and 
00 = 2-digit message memory location: 10 - 19 personal m94 XXX p YYY pun [M] 
messages and 60 u 99 = system messages). 
After b 00 is entered, the previously stored message (M) is 
displayed. (If there is no stored message, nothing is displayed.) 
6 
To Change the Message (M+) m94 Xxx p YYY pun [M+] 
Set the terminal keyboard to upper case and change message 
as required (alphanumeric, 32 characters max. for total message). 
7 
To Set Message 
Set the terminal keyboard to lower case and enter B 11 . m94 XXX p YYY pun [M+] p m0 
Destination station: MW/FL LED flashes, “CALL YYYM” is 
displayed. -L Zero 
Origination station: “SENT XXXM” is displayed. 
8 
To Exit the Message Mode m0 
At any time, enter1 11 (lower case). 
q 
>MODE 
NOTES: 
1. Press 1 at any time to start over. 
2. [M] represents the message entered. 
3. With 
Release 2 software on/y, remote called station messaging is not available from electronic 
telephones, but it is available from ASCII terminals connected to the 
TTYport or via III/ID(J on the 
PIOU or PIOUS. 
-54-  
						

							STEP 
1 
2 
6 
7 
8 
REMOTEADMIN &MAlNTPROCEDURES 
SECTlON200-096-600 
FEBRUARY1991 
TABLERM-BG 
MODE96 
REMOTECALLEDSTATION MESSAGlNG(ADD/CHANGE) 
ACTION 
Enter the Message Mode 
At the >MODE prompt, enter fl 0 a H q . 
To Change or Add a New Called Station Message 
Set the terminal keyboard to the lower case (cap lock off) and 
enter Q[I 
NOTE: 
Enter “m” (lower case) anytime it is desired to start over 
in this procedure. 
Enter 1 1 13 (XXX = destination station number or destination 
station group number - 30 = all EKTs, 31 - 34 per system, 
Program 31). 
Enter ![[I (p = page command and YYY = originating 
station number). 
Enter B 00 (p = page command and 
00 = 2-digit message memory location: 10 * 19 personal 
messages and 60 w 99 = system messages). 
To Add the New Message [M] 
Set the terminal keyboard to upper case and enter message 
as required (alphanumeric, 32 characters max.). New message 
displays as it is entered. 
To Set the Message 
Set the terminal keyboard to lower case and enter B 11 . 
Destination station: MW/FL LED flashes, “CALL YYYM” is 
displayed on LCD. 
Origination station: “SENT XXXM” is displayed on LCD. 
To Exit the Message Mode 
At any time, enter m 11 (lower case). 
DISPLAY/PRINTOUT 
>MODE MESG 
m 96 
m96 XXX 
m96 XXX p YYY 
m96 XXX p YYY pflo 
m96 XXX p YYY pnn[M] 
m96 XXX p YYY pnn[M] p 
m0 
-L 
Zero 
m0 
q 
>MODE 
NOTES: 
1. [M] represents the message entered. 
2. With 
Release 2 software only, remote called station messaging is not available from electronic 
telephones, but it is available from ASCII terminals connected to the TTYport or via IMDU on the 
PIOU or PIOUS. 
-55-