Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual
Have a look at the manual Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
INSTALLATION-WIRING DIAGRAMS SECTION 200-096-209 FEBRUARY 1991 TABLE 9-B STATION LOOP REQUIREMENTS Device Description PEKU (ckts 1 - 8) Electronic P%JZ telephone, door phone/ control boxes (ckts 5 - 8) PEKU (ckts 7 & 8) DSS consoles Max Loop Resistance Max Distance from (Including Device) KSU to Device 40 ohms 1000 ft. (303 m) 20 ohms 500 ft. (152 m) Number of Wire Pairs 1 All need 2-pair. EKTs which receive OCA calls need 3-pair.’ PSTU Standard Approx. 3000 ft. (909 m) (ckts 1 - 8) telephones, with 150 ohm device. See P&U * voice mail, 300 ohms manufacturer’s product auto attendant, specifications for exact (ckts 1 & 2) etc. resistance of device. PDKU Digital (ckts 1 - 8) telephones 40 ohms 1000 ft. (303 m) PDKU (ckt 8) DDSS consoles 40 ohms 1000 ft. (303 m) PDKU (ckts 1 - 7) PDIU-DI 40 ohms 1000 ft. (303 m) PDKU (ckts 1 - 7) PDIU-DS 40 ohms 1000 ft. (303 m) NOTES: 1. Use 24 A WG twisted pairs. 2. PESU circuits 3 and 4 are not used. 3. Two-pair or larger wire is required to achieve maximum range, see table 9-D. 1 -pair 1 -pair 1 -pair Shares digital telephone wire-pair? 1 -pair3 TABLE 9-C NETWORK REQUIREMENTS I TOSHIBA TOSHIBA Printed Circuit Board Printed Circuit Board I Pcou/Pcou2 Pcou/Pcou2 (Loop Start Line) (Loop Start Line) PEMU PEMU (Type I, TIE Line) (Type I, TIE Line) 2-wire 2-wire 4-wire 4-wire PESU*/PSTU/PSTU2 (Off-premises Station) 02LS2 RJ14C 0.2B TLIlM RJ2EX N/A TL31 M RJ2GX N/A OL13A RJ21 X N/A I *Circuits 1 and 2 Facility Interface Code Ringer Equivalence 9-2
INSTALLATION-WIRING DIAGRAMS SECTION 200-096-209 FEBRUARY 1991 TABLE 9-D DIGITAL TELEPHONE/DIU/DDSS CONSOLE/LOOP LIMITS . PPSU 1 OOOft (303m) 1 OOOft (303m) DDSSI 060A Battery Backup 500ft (151m) 1 OOOft (303m) *Battery backup applies to instances when the system is being powered by batteries exclusively. 9-2A
INSTALLATION-WIRING DIAGRAMS SECTION 200-096-209 FEBRUARY1991 This page is intentionally blank. 9-2B
INSTALLATION-WIRING DIAGRAMS SECTION 200-096-209 FEBRUARY1991 BUILDING #l BUILDING #2 TELEPHONE &I Secondary protectors PEMU PEMU PCOU PCOU 1 I E&M TIE LINE CO LINE HtiUHt Y-A-StWNDARY PROTECTOR DIAGRAM IMPORTANT! To protect against transient voltages and currents, secondary protectors must be installed if there is outside wiring (Figure 9-A). These protectors, which contain fast semiconductors in addtion to fuses, shall comply with the requirements forsecondarypro tectors for communica tion circuits, UL 497A. As of October I, 1990, the following manufacturers offer secondary protectors that are UL listed. 9-2c
INSTALLATION-WIRING DIAGRAMS SECTION 200-096-209 FEBRUARY1991 1. Certron Corp; Anaheim, California 92807 l Secondary protector: Model 08450. 2. Curtis Mfg. Co. lnc; Jaffrey, New Hampshire 03452 l Secondary protector: Model Diamond Chip. For indoor use on the protected side of the telephone circuit only. 3. Oneac Corp; Libertyville, Illinois 60048 l Secondary protector: Model OnLine 614+ and OnLine DG/S. For indoor use on the protected side of primary telephone protector only. 4. Siemon Co.; Watertown, Connecticut 06795 l Secondary protector for communication circuits: Model PM-2305. Intended for use with Listed Siemon 66Ml Block: Models PG-04, -25, -50, or PK-04 ground kit and Listed Type I enclosure. For use on the protected side of a Listed Primary Telecommunications Protector for indoor use only. 5, Simplex Time Recorder Co.; Gardner, Massachusetts 07440 l Isolated loop circuit protectors: Models 2081-9027 and 2081-9028. Intended for use between data communication equipment or signal lines of building system equipment. Install and test the secondary protectors per the installation instructions of the applicable manufacturer. 9-2D
INSTALLATION-WIRING DIAGRAMS SECTION 200-096-209 FEBRUARY 1991 TO P C EKU W/FEMALE :ONNECTOR BRIDGING VOICE Tl DATA Ti DATA RI =+r CIRCUIT 4 1 654321 R1 OCA Rl STATION CABLE TWISTED PAIR 1 PAIR IG CIRCUIT 5 NOTE: See Program 28 for electronic telephone CIRCUIT 6 to DSS assignments. VOICE PAIR-NOT USED CIRCUIT 7 DATA TIP 7 DATA RING 7) I TELEPHONE IR-NOT USED ASSOCIATED WITH DSS/BLF ‘ATION CIRCUIT 3 ELECTRONIC TELEPHONE CIRCUIT 4 RECEIVES OFF-HOOK CALLS NOTE: Place PEKlJ SW1 to DSS. GN-Y 1 18 - &; LY-BR ! 44 ; k BR-V ! 24 ; NOTE: See Program 27 to assign DSS buttons. loop resistance: 20 ohms from PEKU to DSS (500 ft). DSS/BLF CONSOLE FIGURE 9-2 MDF WIRING/DSS/BLF CONSOLE AND ASSOCIATED ELECTRONIC TELEPHONE WIRING TO PEKU 9-4
INSTALLATION-WIRING DIAGRAMS SECTION 200-096-209 FEBRUARY1991 TO PEKU OR PESU W/FEMALE CONNECTOR BR’DG’NG /-I InP 66M150 SPLIT BLOCK ’ CIRCUIT 5 CIRCUIT 6 CIRCUIT 7 CIRCUIT 8 NOT USED SCREW 1654321 u uuun I I l”lYL n MDFB (REAR VIEW) ( , ; 4 , / lDOO$--1 I VR VT MDFB DOOR PHONE B OR DOOR LOCK CONTROL I I I See Note I l J See Note 2 1 MDFB (DOOR PHONE) STATION #s See Note 3 NOTES: 26 1 161 1 162 1 163 1. On PEKU or PESU, cut W9. See Programs 39, 77-I. 77-2, and 79. 2. HDCB “B” output options: SWI: Always in DOOR position. SW2: DOOR position; “B” connects to door phone. LOCK (Release 2 only) position; “B” connects to door lock. 3. Door phones may be connected to circuit 5 on ports 4, 12,20 and 28 only. I FlGURE9-3-MOFWIRING-DOOR PHONE/LOCKTO PEKU/PESU 9-5
INSTALLATION-WIRING DIAGRAMS SECTION 200-096-209 FEBRUARY 1991 TO PEKU W/FEMALE ‘CONNECTOR BRIDGING STATION CABLING (24 AWG, TWISTED PAIRS) VOICE Tl (VT) 1 VOICE RI (VR) DATA Tl (DT) DATA Rl (DR) J TO ELECTRONIC TELEPHONE 1 (PORT 00) CIRCUIT 2 TO ELECTRONIC TELEPHONE (PORT 01) I. Available with R2 software only. BACKGROUND MUSIC \,R9 l!=mRT n3 - SOURCE OUTPUT (600 OHMS; 1 V RMS MAX) CAUTION: To avoid distortion, do not connect port 02 to 8-ohm outputs. PTRONIC .03) CIRCUIT 4 TO ELEC TELEPHONE (PORT CIRCUIT 5 TO ELEC TELEPHONE OR :TRONIC 36 NOTES: I. PEKU must be installed in slot 01. 2. Program 10-2, button/LED 09 “‘on’: fo. BGM connection to port 02. 3. Cut W5 jumper on PEKU in slot 01. 4. Provide BGM to electronic telephone and external page (PIOU/PIOUS/PEF 5. Volume is adjusted at BGM source on/y (not at PEKU). r spe, ‘U). akers A -- II ! DR 1 OR DSS (PORT 06) ~-j$--#~~ 1 -0CATi (OT) 1 OCA Rl (OR) TO EL 1-1 /_- -- ‘- ’ - .ECTRONIC TELEPHONES THAT RECEIVE oc CIRCUIT 2 TO ELECTRONIC TELEPHONES THAT RECEIVE OCA CIRCUIT 3 TO ELECTRONIC TELEPHONES THAT RECEIVE OCA CIRCUIT 4 TO ELECTRONIC TELEPHONES THAT RECEIVE OCA CIRCUIT 5 TO ELECTRONIC TELEPHONES THAT RECEIVE OCA CIRCUIT 6 TO ELECTRONIC TELEPHONES THAT RECEIVE OCA CIRCUIT 7 TO ELECTRONIC TELEPHONES THAT RECEIVE OCA CIRCUIT 8 TO ELECTRONIC TELEPHONES THAT RECEIVE OCA NOT USED L v-o -a
INSTALLATION-WIRING DIAGRAMS SECTION 200-096-209 FEBRUARY1991 MDF BLOCK NO. DKSU SLOT NO. . NOTES: 1. Indicate if BGM or electronic telephone is connected (see Program IO-2 and 19); BGM connects to VT and VR, circuit 3 only (DT and DR not used). 2. Indicate if electronic telephone or HDCB (allowed HDCB port numbers: 04, 12, 20, 28). 3. Indicate if electronic telephone or DSS no. 1, 2, 3, or 4. 4. Copy for each PEKU installed. 5. OCA wiring not shown, see MDF-to-electronic telephone wiring. FlGURE9-5-PEKUSTATION/MDFCROSSCONNECTRECORD 9-7