Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

							INSTALLATION-PERIPHERALS 
SECTION 200-096-208 
FEBRUARY 1991 
PDIU-DS (FRONT VIEW) PDIU-DS (REAR VIEW) 
MODULAR JACK 
FOR CONNECTING 
I- OR 2-PAIR 
E FIGURE 8-26 FOR 
(1 - 4) OPTIONS 
INFORMATION 
(SEE PARAGRAPH 12.72) 
Pl - P9 LOCATED ON PCB INSIDE 
OF PDIU-DS UNIT (SEE NOTES) 
n 
I 
RI J 
DTR RS-232, DB25 
(FEMALE) CONNECTOR 
I SIGNAL DIRECTION 
PDIU-DS CONNECTED TO DTE 
PDIU-DS CONNECTED TO DCE 
SIGNAL 
ABBREVIATON SIGNAL NAME/ 
FUNCTION FUNCTION: 
PDIU-DS SIGNAL A-B 
PIN NO. DIRECTION (DTE MODE) FUNCTION: 
SIGNAL B-C 
DIRECTION (MODEM MODE) 
FG FRAME GROUND 1 
SG SIGNAL GROUND 
7 
TD TRANSMIT DATA 
RD 
I RECEIVE DATA 
DTR 1 DATA TERMINAL READY 1 20 1 DTE DIU P3 ND FUNCTION OF PI - P9 
MODEM DIU 1 P2 
MODEM DIU P6 
MODEM DIU 
I P3 
MODEX DIU 
I P0 
MODEM DIU 1 P9 
NOTES: 
1. Mode select (Pl - P9) ‘A-B” if PDIU-DS IS connected to a terminal-type device (DTE). 
2. Mode select (Pl - P9) “B-C” if PDIU-DS is connected to a modem-type device (DCE). 
3. See Figure 8-27 to disassemble/assemble PDIU-DI. 
4. Some RS-232 leads go by different names depending on the equipment manufacturer. 
FIGURE 8-28-PDIU-DS JUMPER PLUG OPTIONWRS-232 CONNECTOR INFORMATION 
8-48  
						

							INSTALLATION-PERIPHERALS 
SECTION 200-096-208 
FEBRUARY1991 
TOSHIBA LAPTOP OR IBM AT-TYPE 
PERSONAL COMPUTER (DTE) 
PIN DESIGNATIONS PDIU-DI 
(FUNCTIONS LIKE A DCE) 
PIN DESIGNATIONS 
CoK:RT PDIU-DI 
123456789 PIN# 1 2 3 4 5 6 7 8 20 22 
NAME DCD RD TD DTR SG DSR RTS CTS RI NAME FG TD RD RTS CTS DSR SG DCD DTR RI 
Rear view of asynchronous (serial) 
communication interface connector (DB9) of Rear view of PDIU-DI DB25, 
RS-232 female connector 
Toshiba laptop or IBM AT personal computer 
CONNECTOR 
DB9 
FEMALE 
CONNECTOR 
4 
5 
22 Pin to pin connections are 
confiqured as a straight cable, 
not as a null modem cable 
(50 ft max, 24AWG; 
customer supplied). 
NOTES: 
7. Some RS-232 E/A leads may be called by other names by some manufacturers. 
2. The computer receives data on pin 2 (RD) and sends data on pin 3 (TO). , 
FIGURE 8-29-PDIU-DI TO IBM AT TYPE COMPUTER RS-232 CONNECTOR/CABLE CONNECTIONS 
8-49  
						

							INSTALLATION-PERIPHERALS 
SECTION 200-096-208 
FEBRUARY1991 
IBM XT PERSONAL COMPUTER 
OR ASCII TERMINAL 
(FUNCTIONS LIKE A DTE) 
DB25 PIN DESIGNATIONS 
PDIU-DI 
PIN# 1 2 3 4 5 6 7 8 20 22 
NAME FG TD RD FITS CTS DSR SG DCD DTR RI 
Rear view of personal computer 
PDIU-DI 
PIN# 1 2 3 4 5 6 7 8 20 22 
NAME FG TD RD RTS CTS DSR SG DCD DTR RI 
PDIU-DI 
(FUNCTIONS LIKE A DCE) 
DB25 PIN DESIGNATIONS 
RS-232 CABLE 
. DB25 
DB25 
PIN# NAME PIN # 
8 DCD 8 
3 RD 3 
2 TD 2 
20 DTR 20 
7 SG 7 
6 DSR 6 
4 RTS 4 
5 CTS 5 
22 RI 22 
1 FG 1 IBM PC AT modem style (serial) 
DB25 to DB2.5 (M/F) E-232 
cable (50 ft max, 24 AWG, 
customer supplied). 
NOTE: 
The PC/ASCII terminal receives data on pin 3 (RD) and transmits data on pin 2 (TO). 
I FIGURE 8-30-POIU-DITOIBMXTTYPE COMPUTER, RS-232 CONNECTOR/CABLE CONNECTIONS 
8-50  
						

							INSTALLATION-PERIPHERALS 
SECTION 200-096-208 
FEBRUARY1991 
TOSHIBA PS321 SL PRINTER 
(FUNCTIONS LIKE A DTE) 
DB25 PIN DESIGNATIONS 
PRINTER 
PIN# 1 2 3 4 5 6 7 8 20 22 
NAME FG TD RD RTS N/C DSR SG DCD DTR RI 
PDIU-DS 
(CONFIGURED IN THE “CONNECT TO DTE” MODE: 
PI - P9 
q A-B SO PDIU FUNCTIONS LIKE A DCE) 
DB25 PIN DESIGNATIONS 
PDIU-DS 
PIN# 1 2 3 4 5 6 7 8 20 22 
NAME FG TD RD RTS CTS DSR SG DCD DTR RI 
Rear view of Drinter 
(50 ft max, 24 AWG; 
customer supplied). 
NOTES: 
1. The printer receives data on pin 3 (RD) and transmits data on pin 2 (TO). 
2. The PDIU-DS should be in the connect to DTE mode (Pl m P9 are strapped A-B), 
so that it transmits data on pin 3 (RD) and receives data on pin 2 (TO). 
FlGURE8-31-PDIU-DSTOTOSHlBAPRINTER,RS-232CONNECTOR/CABLE CONNECTIONS 
8-51  
						

							INSTALLATION-PERIPHERALS 
SECTION 200-096-208 
FEBRUARY 1991 
HAYES-TYPE SMART MODEM 
(FUNCTIONS LIKE A DCE) PDIU-DS 
(CONFIGURED IN THE “CONNECT TO MODEM” 
MODE, PI - P9 = B-C, SO IT FUNCTIONS LIKE A DTE) 
MODEM PDIU-DS 
PIN# 1 2 3 4 5 6 7 8 20 22 PIN# 1 2 3 4 5 6 7 8 
20 22 
NAME FG TD RD FITS CTS DSR SG DCD DTR RI 
NAME FG TD RD RTS CTS DSR SG DCD DTR RI 
Rear view of modem DB25 connector 
Rear view of PDIU-DS DB25, connector 
W-232 CABLE 
(50 ft max, 24 AWG; 
customer supplied) 
NOTES: 
1. Modem receives data on pin 2 (TO) and transmits data on pin 3 (RD). 
2. The PDIU-DS must be in the connect to modem mode (Pl - P9 strapped B-C) so that it transmits 
data on pin 2 (TO) and receives data on pin 3 (RD). 
FIGURE 8-32-PDIU-OS TO HAYES-TYPE SMART MODEM, RS-232 CONNECTOR/CABLE CONNECTIONS 
8-52  
						

							INSTALLATION-PERIPHERALS 
SECTION 200-096-208 
FEBRUARY1991 
CONNECTION EXAMPLE 1 
DIGITAL TELEPHONE 
. 
TOSHIBA LAPTOP OR IBM AT TYPE 
PERSONAL COMPUTER (PC) 
PDIU-DI BASE 
TYPE 1 MODULAR ADAPTER’ 
TYPE B MODULAR CORD (CROSSED) 
(50 ft max, 24AWG) 
TYPE 2 MODULAR ADAPTER’ 
IMPORTANT! 
Will not function with applications that require the RI signal to PC. 
CONNECTION EXAMPLE 2 
DIGITAL TELEPHONE IBM PC OR XT TYPE 
PERSONAL COMPUTER (PC) 
PDIU-DI BASE 
MODULAR ADAPTER’ 
TYPE A MODULAR CORD (STRAIGHT) 
(50 ft max, 24AWG) 
TYPE 2 MODULAR ADAPTER’ 
IMPORTANT! 
Will not function with applications that require the RI signal to PC. 
CONNECTION EXAMPLE 3 
TOHSIBA P321 SL OF SIMILAR 
STAND-ALONE DIU 
I 
PDIU-DS TANDARD TYPE SERIAL PRINTER 
TYPE 2 MODULAR ADAPTER’ 
TYPE A MODULAR CORD’ 
(50 ft max, 24AWG) 
TYPE 2 MODULAR ADAPTER’ 
NOTES: 
1. See Figure 8-34 for detailedpin out information of modular cords and adapters. 
2. Never use modular cords and adapters when connecting a PDIU-DI/PDIU-DS to a modem. 
3. Connection examples 1 and 2 work when using the PDIU-DI to make calls with personal computer 
applications (auto-dialers, printer sharing, outgoing modem calls, etc). If the PC PDIU-DI must receive 
calls, the RI lead is normally required; therefore, a standard RS-232 cable must be used (see Figures 
8-29 and 8-30). 
4. In Connection Example 3, PDIU-DS must be in the connect to DTE mode 
(Pl B P9, strapped A-B). 
5. All modular cords and adapters are customer-supplied. 
I 
FlGURE8-33-PDIU-DI/PDIU-DS MODULAR CABLE/RJ-45ADAPTER CONNECTIONS 
8-53  
						

							INSTALLATION-PERIPHERALS 
SECTION 200-096-208 
FEBRUARY 1991 
TYPE 1 0 . 
RJ45 TO DB9 (FEMALE) ADAPTER 
87654321 
8 7 6 5 4 2 1 N/C RJ45 
DSR RTS RD DCD TD GND CTS RI LEAD 
NAME 
6 7 2 b 3 5 8 9 DB9 
54321 
oo”oooooo 
9876 
TYPE 2 
RJ45 TO DB25 (MALE) ADAPTER 
I!3 
87654321 
8 7 6 5 4 3 2 1 N/C RJ45 
CTS SG DTR TD DCD RD 
RTS DSR RI LEAD 
NAME 
5 7 2((j 22 DB25 
TYPE 3 
RJ45 TO DB25 (FEMALE) ADAPTER 
L3 
87654321 
8 7 6 5 4 3 2 1 N/C RJ45 
CTS SG DTR TD 
DCD RD RTS DSR RI LEAD 
NAME 
5 7 2&iz&j 22 DB25 
TYPE A 
RJ45 FLAT MODULAR 
CORD (STRAIGHT) RJ45 STRAIGHT THROUGH 
FRONT 
: 
: 
z 
i 
RJ45 CROSS PINNING 
TYPE B 
RJ45 FLAT MODULAR 
CORD (CROSSED) 
Modular Cords (50 ft max, 24AWG; customer supplied) 
I 
FIGURE 8-34-POIU-DI/PDIU-DS MODULAR CORDS AND RJ-45/RS-232 ADAPTER PIN CONNECTIONS 
8-54 
i  
						

							INSTALLATION-PERIPHERALS 
SECTION 200-096-208 
FEBRUARY1991 
. LAPTOP PC 1 
STRATA DK (Release 3) 
LAPTOP PC 2 
FlGURE8-35-PCTO PCTESTCALLUSINGATCOMMANDS 
12.80 PDIU-DVPDIU-DS Installation Tests 
12.81 Paragraphs 12.82 -+ 12.86 provide tests for 
five DIU call applications. The telephone and port 
numbers used in these figures are provided for 
explanation purposes only; when actually testing, 
use port and telephone numbers appropriate for 
the system. Each of these tests can be conducted 
with manual dialing from adigital telephone’sdialpad 
or AT dialing from a personal computer’s keyboard; 
however, only the preferred method of dialing for 
application is presented. The Data hterface User 
Guide in the Operating Procedures section of this 
manual has additional information useful for the 
tests. 
12.82 PC-to-PC Test Call Using AT Commands 
(see Figure 8-35) 
2) Make sure PC 1 and PC 2 are on-line with a 
communications software package and that 
the communication parameters of each PC 
and communication software package are set 
to the same values (data transmission rate, 
parity, data bits, stop bits, flow control, etc.). 
3) From PC l’s keyboard, type~~~~~~[and 
press m (AT commands must be capital 
letters). 
l The DATA LEDs will be lit on DKT 200 
and 201 
l PC 1 displays, CONNECT XXXX. 
l PC 2 displays, RING. 
l PC 1 and PC 2 are connected as shown 
by the thick solid lines. PDIU-Dls are 
now in the communication mode. 
1) DIU Programming: 
l Program 20: Ports 00 and 01. LEDs 01, 
02, and 17 ON; all other LEDs OFF. 
l Program 39: Ports 00 and 01. m (56) 
and m (54) buttons should be pro- 
vided. 
l Default settings for PDIU-DI S-Registers. 4) Typing from PC 1 keyboard will display on 
PC 
2 display and vice versa. 
5) To terminate the call: 
a) Type 1 B 4 from either PC keyboard. 
l The PC screen displays, OK: 
b) Type lR[3f rom the PC keyboard used 
in step 5a. 
8-55  
						

							INSTALLATION-PERIPHERALS 
SECTION 200-096-208 
FEBRUARY1991 
STRATA DK (Release 3) 
nnne I 
RS- 
RS- 
FlGURE8-36-PCTO PRINTERTESTCALL USING MANUAL DIALING 
l PC 1 and PC 2 screens both display, 
NO CARRIER. 
l The Data LEDs on each DKT are off. 
12.83 PC to Printer Test Call Using Manual 
Dialing (see Figure 8-36) 
1) DIU Programming: 
l Program 20: Port 01. LEDs 01, 02, and 
17 ON; all other LEDs OFF. 
l Program 20: Port 03. LEDs 01,04, and 
17 ON; all other LEDs OFF. 
l Program 39: Port 01. m (56) and 
m (54) buttons should be provided. 
l Default settings for PDIU-DI, S-Registers. 
2) Make sure the PC is configured to print data 
from its serial COM port (the PC COM port 
connected to DKT/PDIU-DI port 01). This is 
normally accomplished using the DOS and 
MODE commands. 3) Using the manufacturer’s documentation, 
make sure the communication parameters 
(data speed, parity, data bits, stop bits, etc.) of 
the PC COM port match the printer’s serial 
interface parameters. 
4) To connect the PC to the printer, press the 
DKT’s m button and dial 111 . 
l The CONNECT on the PDIU-DS will be 
lit. 
l The connection between the PC and the 
printer is completed, as shown by the 
thick lines above (PDIU-DS 203 is in the 
communication mode). 
l If busy tone is sent to the DKT, the 
connection is not complete; press m 
and try step 4 again. 
5) Operate the PC to print data as required. 
6) To terminate the call, press the DKT’s m 
button. 
I 
8-56  
						

							INSTALLATION-PERIPHERALS 
SECTION 200-096-208 
FEBRUARY 1991 
LAPTOP PC 1 STRATA DK (Release 3) 
583-3700 
7-l 
- 
TELEPHONE 
PC2 
FIGURE 8-37-INTERNAL PC TO EXTERNAL PC TEST CALL USING AT COMMANDS 
12.84 Internal PC to External PC Test Call Using 
AT Commands (see Figure 8-37) 
1) DIU Programming: 
l Program 20: Port 00. LEDs 01,02, and 
17 ON; all other LEDs OFF. 
l Program 20: Port 04. LEDs 01, 02, 03, 
04, and1 7 ON; all other LEDs OFF. 
l Program 21: PDKU port 04 assigned 
with PSTU oort 08. 
l Program 39: Port 00. [iKEI (56), m 
(54), and ma (55) buttons should 
be provided. 
l Default settings for PDIU-DI and PDIU- 
DS S-Registers. 
2) Make sure PC 1 and PC 2 are on-line with a 
communications software package and that 
the communication parameters of each PC 
and communication software package are set 
to the same values (data transmission rate, 
parity, data bits, stop bits, flow control, etc.). 3) From PC l’s keyboard, type1~~~~~~and 
press m (AT commands must be capital 
letters). 
l The DATA LED on DKT 200 will be lit. 
l The CONNECT LED on PDIU-DS 204 
will be lit. 
l The screen on PC 1 displays, CON- 
NECT XXXX, where XXXX is the data 
transmission speed set by the communi- 
cations software. 
l At this time, PC 1 and PDIU-DS 204 are 
connected as shown by the thick lines 
above (PDIU-DS 204 is in the communi- 
cation mode); PC 1 is now linked directly 
to the RS-232 side of the internal mo- 
dem; PC 1 can issue AT commands to 
the internal modem, which is now in the 
command mode. 
l If PDKWPDIU-DS port 04 is the only 
DIU port connected -to the modem 
(Program 20, LED 03 ON), the MODEM 
LEDs on all DKTs will be lit. 
8-57