Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

							PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
PROGRAM51 
LCRAREACOOES 
SELECT = LCR - 
‘Ian N”mber (’ * ‘) Action Code:’ ’ DATA = Area Code(s) 
Enter 2 to add code to table. (3 digits) 
Enter 3 to delete code from table. 
Enter 4# to display codes in table. 
DATA = Area Code(s)  DATA = Area Code(s) DATA = Area Code(s)  DATA = Area Code(s) 
DATA = Area Code(s)  DATA = Area Code(s) DATA = Area Code(s)  DATA = Area Code(s) 
NOTES:  NOTES: 
1. For more information, see the instructions preceding the record sheets.  1. For more information, see the instructions preceding the record sheets. 
2. Initialized data leaves Tables 1 - 7 blank; all codes (000 - 999) are initialized in Table 8.  2. Initialized data leaves Tables 1 - 7 blank; all codes (000 - 999) are initialized in Table 8. 
3. To enter a range of Area Codes, press  3. To enter a range of Area Codes, press 
Low Area Code High 
Area Code besignates 
end of string 
4. Several ranges or individual codes can be expressed at once by separating them with a 1 key. 
2-141  
						

							PROGRAMMINGPROCEDURES-INSTRUCTIONWSYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
PROGRAM51 
LCRAREACOOES 
SELECT = LCR 
y T 7 DATA 
‘Ian N”mber (I * 8, Action Code: Area Code(s) 
Enter 2 to add code to table. (3 digit; 
Enter 3 to delete code from table. 
Enter 4# to display codes in table. 
DATA = Area Code(s) DATA = Area Code(s) 
DATA = Area Code(s) 
DATA = Area Code(s) 
NOTES: 
1. For more information, see the instructions preceding the record sheets. 
2. Initialized data leaves Tables 1 - 7 blank; all codes (000 - 999) are initialized in Table 8. 
3. To enter a range of Area Codes, press 
Low Area Code High 
Area Code besignates 
end of string 
4. Several ranges or individual codes can be expressed at once by separating them with a 1 key. 
2-142  
						

							PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
PROGRAM52 
LCROFFlCECODEEXCEPTlONSFORSPEClFlEDAREACODE 
To assign Office Code Exception Table (1 - 4) to an LCR Plan: 
SELECT= Office Code / / 
Exception Table (l-8) 
Action Code DATA = (See below) 
Action Code Function 
Action Codes 
DATA = 
Assign Exception Table to LCR Plan 
0 0 
El LCR Plan 1 w 8 
Assign Area Code to LCR Plan 
q 1 
q nu 3-digit Area Code 
Add Office Codes to Exception Table 
0 2 
IIKI 3-digit Office Code 
Delete Office Codes from Exception Table 
0 
lIKl 
Display Office Codes in Exception Table film morel#l nnn 3-digit Office Code 
3-digit Office Code 
Office Code Exception Table 
q for Area Code m 
Assign to LCR Route Plan Number 0 
Office Codes: 
Office Code Exception Table 
q for Area Code m 
Assign to LCR Route Plan Number 0 
Office Codes: 
Office Code Exception Table 131 for Area Code m 
Assign to LCR Route Plan Number u 
Office Codes: 
Office Code Exception Table 
q for Area Code m 
Assign to LCR Route Plan Number 0 
Office Codes: 
NOTES: 
1. For more information, see the instructions preceding the record sheets, 
2. Initialized data leaves all codes blank. 
3. To enter a range of office codes, press 
Low ‘Office Code High ‘Designates 
Office Code end of String 
4. Several ranges or individual codes can be expressed at once by separating them with a i key. 
5. Copy as required, maximum eight Office Code Exception Tables. 
2-143  
						

							PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS 
SECTION 200-096-302 
FEBRUARY 1991 
PROGRAM 52 
LCR OFFICE CODE EXCEPTIONS FOR SPECIFIED AREA CODE 
To assign Office Code Exception Table (5 - 8) to an LCR Plan: 
more data 
___._____---._____._____________________------, 
SELECT = Office Code /’ 1 
Exception Table (l-8) Action Code 
DATA = (See below) 
Action Code Function Action Codes 
DATA q 
Assign Exception Table to LCR Plan q 0 
0 LCR Plan 1 w 8 
Assign Area Code to LCR Plan 
0 1 
lzlnlo 3-digit Area Code 
Add Office Codes to Exception Table 
II 2 
q III 3-digit Office Code 
Delete Office Codes from Exception Table 
0 
[710 
l-ilm morem nnn 3-digit Office Code 
Display Office Codes in Exception Table 3-digit Office Code 
Office Code Exception Table 
q for Area Code I[ 
Assign to LCR Route Plan Number 
0 Office Codes: 
Office Code Exception Table m for Area Code m 
Assign to LCR Route Plan Nuzr 
q I I I , Office Codes: 
Office Code Exception Table 
q for Area Code m 
Assign to LCR Route Plan Number 
q Office Codes: 
Office Code Exception Table 
q for Area Code RI 
Assign to LCR Route Plan Number 
q Office Codes: 
NOTES: 
1. For more information, see the instructions preceding the record sheets. 
2. Initialized data leaves all codes blank. 
3. To enter a range of office codes, press 
Low Office Code High 
Office Code Designates 
end of String I 
4. Several ranges or individual codes can be expressed at once by separating them with a [ key. 
2-144  
						

							PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS 
SECTION 200-096-302 
FEBRUARY 1991 
PROGRAM 53 
LCR SCHEDULE ASSIGNMENTS 
FOR LCR PLAN NO. 1 AND 2 
more data 
, 
SELECT = 
SELECT Start TM 
II 
Start TM 
Schedule (1 * 3) 
Plan1 
LCR Plan 2 
HHMM 
(HH =OO-23 
MM = 00 - 59) LCR Plan - I I HHMM 
Schedule (1 s 3) --I (HH =OO-23 
Action co;c ’ 1 MM = 00 -5% 
SELECT DATA (Ryte Choices) 
I SELFCT DATA (Ryte Choices) 
Schedule 1 
Route Choices 
For Plan 1 1 1 1 
1 1 2 
~ 1 1 3 
1 1 4 
Schedule 2 
Route Choices 
For Plan 1 
Schedule 3 
Route Choices 
For Plan 1 
LCR Plan - 
Schedule (1 +. 3) 1 2 1 
1 2 2 
~ 1 2 3 
1 2 4 
1 3 1 
1 3 2 
I3 1 3 3 
1 3 4 
--- 
--i 
I I 
I 1 
-r-l--T-T 
1st 2nd 3rd Last 
LCR Staticn ’ 1 (Route Definition 
Group No. (1 N 4) No’s (1 - 4) 
(see 
Program 56 ) From Program 54 ) 
Start TM 
Schedule 
Plan 2 
.&art TM or DATA 
SELECT 
Start TM 
(1 -3) 
Schedule 1 
Route Choices 
For Plan 2 
Schedule 2 
Route Choices 
For Plan 2 
Schedule 3 
Route Choices 
For Plan 2 
LCR Plan- 214 
1st 2nd 3rd Last 
Schedule (1 w 3) - 
1 
LCR Stati.n ’ 1 (Route Definition 
Group No. (1 w 4) No’s (1 - 4) 
(see Program 56 ) From Program 54 ) 
NOTES: 
1. For more information, see the instructions preceding the record sheets. 
2. Initialized data assigns starting time as 0000 and Route Definitions as blank for all schedules. 
3. If schedules 1 & 2 start at the same time, then Time of Day schedule change does not occur, and data 
only needs to be entered for schedule 1. 
4. Press LED key 01 to erase data (LED does not light). 
2-145  
						

							PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS 
SECTION 200-096-302 
FEBRUARY 1991 
PROGRAM 53 
LCR SCHEDULE ASSIGNMENTS 
FOR LCR PLAN NO. 3 AND 4 
more data 
._ 
SELECT = 
Start TM or DATA 
SELECT Start TM SELECT 
Start TM 
Start TM 
Schedule (1 - 3) 
I I Plan 3 
I ’ ’ ’ J 
LCR Plan 2 TT HHMM Start TM 
Schedule (1 - 3) 
Plan 4 
LCR Plan 
A I I Ht  --- 
i M M 
Schedule fl - 3) AI (HH =OO-23 
Schedule (1 - 3) -.---- 
Action co;lc ’ 1 ‘MM = 00 - 59) 
SELFCT DATA (Ryte Choices) SELECT DATA (Rpute Choices) I 
311 
312 
3 1 3 
3 1 4 
3 2 1 
3 2 2 
El 3 2 3 
3 2 4  Schedule 1 
Route Choices 
For Plan 3 Schedule 1 
Route Choices 
For Plan 4 
Schedule 2 
Route Choices 
For Plan 3 Schedule 2 
Route Choices 
For Plan 4 
33 1 
3 3 2 
ml 
333 
3 3 4 
--- 43 1 
432 
I# 
433 
434  Schedule 3 
Route Choices 
For Plan 4  Schedule 3 
Route Choices 
For Plan 3 
LCR Plan A 
I I I 
1st 2r!rd 3rd Last LCR Plan 27 
Schedule (1 - 3) 1 
Group No. (1 - 4) 
(see Program 56 ) From Program 54 ) LCR Station 
Group No. (1 - 4) 
(see Program 56 ) -r-T-T-r 
1st 2nd 3rd Last 
(Route Definition 
No’s (1 - 4) 
From Program 54 ) 
NOTES: 
1. For more information, see the instructions preceding the record sheets. 
2. Initialized data assigns starting time as 0000 and Route Definitions as blank fo.r all schedules. 
3. If schedules I & 2 start at the same time, then Time of Day schedule change does not occur, and data 
on/y needs to be entered for schedule 1. 
4. Press LED key 01 to erase data (LED does not light). 
2-146  
						

							PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
PROGRAM53 
LCRSCHEDULEASSIGNMENTS 
FORLCRPLANNO.5AND6 
more data 
I 
/ 
SELECT = 
SELECT Start TM 
II 
Start TM 
Schedule (1 - 3) 5 2 
Plan 5 
ml$fq 
--- 
LCR Plan 2 HHMM 
(HH =OO-23 
MM = 00 - 59) Start TM 
Schedule (1 
- 3) 
Plan J?- 
LCR Plan - 
Schedule (1 
- 3) 
Action Code -7- 
- I I 
I 
(HH =OO-23 
MM = 00 +. 59) 
SELFCT DATA (Route Choices) 
SELFCT DATA (Rcute Choices) 
Schedule 1 
Route Choices 
For Plan 5 
Schedule 2 
Route Choices 
For Plan 5 
Schedule 3 
Route Choices 
For Plan 5 
LCR Plan I 
Schedule (1 - 3) I I 
1st 2nd 3rd Last 
LCR Stati.n ’ 1 (Route Definition 
Group No. (1 - 4) No’s (1 - 4) 
(see Program 56 ) From Program 54 ) 
NOTES: 
Start TM or DATA 
SELECT Start TM 
Schedule 1 
Route Choices 
For Plan J& 
Schedule 2 
Route Choices 
For Plan 6 
Schedule 3 
Route Choices 
For Plan 6 
-- 
LCR Plan 1 T 
Schedule (1 - 3) 1 -rITr- 
1st 2nd 3rd Last 
LCR Station 
Group No. (1 - 4) 
(see Program 56 ) 
T (Route Definition 
No’s (1 - 4) 
From Program 54 ) 
1. For more information, see the instructions preceding the record sheets, 
2. Initialized data assigns starting time as 0000 and Route Definitions as blank for all schedules. 
3. If schedules I& 2 start at the same time, then Time of Day schedule change does not occur, and data 
only needs to be entered for schedule 1. 
4. Press LED key 01 to erase data (LED does not light). 
2-147  
						

							PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS 
SECTION 200-096-302 
FEBRUARY 1991 
PROGRAM 53 
LCR SCHEDULE ASSIGNMENTS 
FOR LCR PLAN NO. 7 AND 8 
more data 
1 
Start TM 
Schedule 
Plan 7 
SELECT = 
SELECT Start TM 
LCR Plan JTT HHMM 
SELECT DATA (Route Choices) 
Schedule 1 
Route Choices 
For Plan 7 
Schedule 2 
Route Choices 
For Plan 7 
I 
Schedule 3 
Route Choices 
For Plan 7 
1st 2nd 3rd Last  LCR Plan - 
Schedule (1 m 3) 
LCR Station 
Group No. (1 N 4) 
(see Program 56 ) (Route Definition 
No’s (1 * 4) 
From Program 54 )  
Start TM or DATA 
SELECT 
Start TM 
Start TM 
Schedule (1 w 3) 
Plan 8 
LCR Plan 2 
TT HHMM 
Schedule (1 w 3) - 
SELECT DATA (Ryte Choices) 
I 
Schedule 1 
Route Choices 
For Plan 8 
Schedule 2 
Route Choices 
For Plan 8 
Schedule 3 
Route Choices 
For Plan 8 
LCR Plan 2 
Schedule (1 w 3) ---I 
LCR Station 
Group No. (1 m 4) 
(see Program 56 ) 1st 2nd 3rd Last 
(Route Definition 
No’s (1 m 4) 
From Program 54 ) 
NOTES: 
1. For more information, see the instructions preceding the record sheets. 
2. Initialized data assigns starting time as 0000 and Route Definitions as blank for all schedules. 
3. If schedules 1 & 2 start at the same time, then Time of Day schedule change does not occur, and data 
only needs to be entered for schedule 1. 
4. Press LED key 0 1 to erase data (LED does not light). 
2-148  
						

							PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
PROGRAM54 
LCRROUTE DEFlNlTlONTABLES(l-4) 
SELECT q 
Route Definition Table 
for LCR Plan 
q 
Route Definition Table 
for LCR Plan 
q 
Route Definition Table 
for LCR Plan 
q 
Table 
SELECT = 
Enter Data 
$ 
II 
CODE = 
-CODE q CO line group and 
modified digits table 
NOTES: 
1. For more information, see the instructions preceding the record sheets. 
2. Initialized data is “11”. 
2-149  
						

							PROGRAMMINGPROCEDURES-INSTRUCTIONWSYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
PROGRAM54 
LCR ROUTE DEFlNlTlONTABLES(5-8) 
SELECT = 
Enter Data 
SELECT = I $ ,p 
Route Definition Table 
for LCR Plan 
q 
mm 
mm 
Route Definition Table 
for LCR Plan 161 
- 
m 
m Route Definition Table 
for LCR Plan 
q 
--) 8 2 
mm 8 3 
8 4 
CODE = 
-CODE q CO line group and 
modified digits table 
LCR Plan No. (5 - 8) 
Route Definition Number Modified digits table 1 - 6, 
see Program 55 
CO line group 1 - 8, 
see Program 16 
NOTES: 
1. For more information, see the instructions preceding the record sheets. 
2. Initialized data is “11 ‘I. 
2-150