Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

							REMOTE ADMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
TABLE RM-2 
PROGRAM 60 
SMDR OUTPUT/ACCOUNT CODE DIGIT LENGTH 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter u a m m 
q P 
2 Enter Program Number 60 P 60 
Press 
q P60 
3 Allow SMDR printout on incoming and outgoing calls. P60 3 1 
Enter: Action code 3. P60 
System will print out “1” if incoming and outgoing calls will be 
printed on SMDR. A “0” will be printed out if only outgoing calls 
will be printed. 
Refer to the System Record Sheet and change (to 1 or 0), if 
required, and press 
q . 
4A 
Set Account Code Digit Length P60 4 06 
Enter: Action code 4. 
The system will display the number of digits allowed in the 
account code. The default is 06. 
Refer to the System Record Sheet and enter the required number 
of digits (04 - 15). 
4B 
SMDR Toll Calls Only P60 5 0 
Enter: Action code 5. 
The system will display the presently selected feature (0 - 5). 
The default is 0. Refer to the System Record Sheet and enter the 
required feature code. 
4C Enter DISA ID Code P60 6 - 
Enter: Action code 6. 
System will display last entered ID code number. Default = Blank. 
5 To Exit Program/Store Data P60 6 NNNN 
A) To store data, press 
q . 
B) To exit this program, press1 1 
q . 
P60 ## 
P 
NOTE: 
Programs 77-I & 77-2, use Type I procedure. 
. . 
-3o-  
						

							REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-Zl 
PROGRAM69 
VERIFIABLEACCOUNTCODEENTRY 
I 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter i a m H 
q . P 
2 Enter Program Number 69 P 69 
Press 
q . 
P69 
3 Refer to the System Record Sheet, and enter the required code P69 001 Nknnm-N 
number (000 - 299). 
Example: code number 001; Enter: B 10. 
The system will display the present account code number 
assigned to 001. 
Note: 
The number of digits will be as defined in Program 60-4. 
4 Refer to the System Record Sheets, and enter the required P69 001 
NIWNNN 987654 
account code number. 
Example: number 987654; Enter: B 10 im 1. 
5 
To Exit Program/Store Data P69 001 NNNNNN 987654 
A) To store data, press (9. 
P69 ## 
B) Continue returning to step 3 until all 
Program 69 data 
P 
is entered. 
C) To exit this program, press 1 B 
q . 
, 
-3OA-  
						

							REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-ZP 
PROGRAM70 
VERlFYACCOUNTCODE/TOLLRESTRlCTlONASSlGNMENT 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter i 1 H 1 
q . P 
2 Enter Program Number 70 P 70 
Press a. P70 
3 Refer to the System Record Sheet, and enter the required code P70 002 00 
number (000 - 299). 
Example: code number 002; Enter: 111. 
The system will display the present digit Restrict (Y) and Toll 
Restriction Status (Z) for entered code number. 
4 Refer to the System Record Sheet, and enter the required P70 002 00 13 
digit Restrict and Toll Restriction data. 
Example: digit Restrict (1) and Toll Restriction (3); 
Enter: 11. 
5 
To Exit Program/Store Data P70 002 00 13 
A) To store data, press 
q . 
P70 ## 
B) Continue returning to step 3 until all 
Program 70 data P 
is entered. 
C) To exit this program, press 11 
q . 
-3OB-  
						

							REMOTEAOMIN &MAlNTPROCEDURES 
SECTlON200-096-600 
FEBRUARY1991 
TABLERM-AA 
PROGRAM78 
CO LINESPECIAL RINGING ASSIGNMENTS-DISA/IMDU/NIGHTRlNGlNG OVER EXTERNAL-PAGE 
;TEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter i 0 m H 
q . P 
2 Enter Program Number 78 P 78 
Press 
q . P78 
3 
Refer to the System Record Sheet and enter the feature number P78 1 
for the feature to be programmed. 
Example: Feature code 1, enter 0 . 
4 Refer to the System Record Sheet and enter the code number P78 13 
for the area of the feature being programmed. 
Example: Code 3, enter 1 
5 Refer to the System Record Sheet and enter the CO line keys that ~78 13 01 N 
will be associated with this feature. 02 N Y 
Example: CO key 01, enter 1 1. 
The system will designate whether the CO key/LED is on/off. 
Refer to the System Record Sheet and change if required. 
Press= to display next CO key/LED. 
6 
To Exit Program/Store Data P78 13 01 N 
A) To store data, press [9 . 
02 N Y 
B) Continue returning to step 3 until all data has been entered 
P78 ## 
for this program. P 
C) To exit this program, press 1 1 
q 
NOTE: 
Program 79 uses Type 2 procedure. 
-31-  
						

							REMOTEADMIN &MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AB 
PROGRAM80 
ELECTRONICTELEPHONERINGINGTONES . 
;TEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode. 
>MODE PROG 
At the >MODE prompt enter B 0 a B 
q . P 
2 Enter Program Number 80 P 80 
Press 
q P80 
3 
Refer to the System Record Sheet and enter the required P80 01 
port number. 
Example: Port 01, enter ip . 
4 Press E key. 
P80 01# 1 
The system will display 1 or 2 corresponding to tone 1 or tone 2. 
5 Refer to the System Record Sheet and change if required. 
P80 01# 1 2 
Example: Tone 2, enter 1 . 
6 
To Exit Program/Store Data P80 Ol# 1 2 
A) To store data, press 
q P80 ## 
B) Continue returning to step 3 until all data has been entered 
P 
for this program. 
C) To exit this program, press 1 a 
q . 
NOTE: 
Programs 81 - 89 use Type 2 procedure. 
-32-  
						

							iTEF 
1 
2 
3 Enter Action Code 1 
4 
5 
REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AC 
PROGRAM93 
CO LINE IDENTIFICATION 
ACTION 
Enter Program Mode 
At the >MODE prompt, enter u m H H q . 
Enter Program Number 93 
Press q . 
Refer to the System Record Sheet and enter the appropriate 
CO line number. 
Example: CO line 2, enter i 1 . 
The system will display previously entered identification 
characters (up to 16 characters). 
Refer to the System Record Sheet and change identification 
if required: 00.. . . . . . . . .[70 (16 characters maximum). 
Example: OVERSEAS. 
To Exit Program/Store Data 
A) To store data, press q . 
B) Continue returning to step 3 until all data has been entered 
for this program. 
C) To exit this program, press 1 1 
q 
DISPLAY/PRINTOUT 
>MODE PROG 
P 
I? 93 
P93 
p93 I 02 
r-m fupfo 76) 
L Current I.D. 
P93 1 02 non (upto 16) 
OVERSEAS 
P93 1 02 nnn lupto 76) 
OVERSEAS 
pg3 ## 
P 
NOTE: 
Use m to clear characters. 
TABLERM-AD 
PROGRAM45-1 
TOLL RESTRICTION DIAL PLAN 
STEP1 ACTION 
I DISPLAY/PRINTOUT 
1 Enter the Program Mode >MODE PROG 
At the >MODE prompt, enter w 0 1 H 
q . P 
2 Enter Program Number 45 P 45 
Press 
q . P45 
3 P45 1 1 Enter the number 1. 
The system will display the present dial plan code number (1 - 5). 
4 Refer to the record sheet and enter the required code number. 
P45 1 1 2 
Example: Code 2, enter 1 . 
5 To Exit Program/Store Data 
A) To store data, press q . 
8) To exit this program, press 1 1 
q . P45 1 1 2 
P45 # # 
P 
-33-  
						

							REMOTEADMIN &MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AD1 
PROGRAM44(AORB) 
TOLLRESTRlCTlONTRAVELlNGCLASSOVERRlDECODEENTRY . 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter a 0 B a 
q . P 
2 Enter Program Number 44 (Do not enter A or B) P 44 
Press 
q . P44 
3 Refer to the System Record Sheet and enter the required Toll P44 1 NNNN 
Restriction Class number (1 - 4). 
Example: Class 1; Enter: [. 
The system will display the present override code assigned to 
that class number. 
4 Refer to the System Record Sheet and enter the required override ~44 1 NNNN 3456 
code number. 
Example: 3456; Enter 1 n i i. 
5 To Exit Program/Store Data P44 1 NNNN 3456 
A) To store data, press 
q . 
p44 ## 
B) Continue returning to step 3 until all 
Program 44 data P 
is entered. 
C) To exit this program, press 11 
q . 
-34-  
						

							REMOTEAOMlN&MAlNTPROCEOURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AE 
PROGRAM45-2 
TOLL RESTRICTION DISABLE 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Program Mode 
>MODE PROG 
At the >MODE prompt, enter i 1 H H 
q . P 
2 Enter Program Number 45 P 45 
Press 
q . P45 
3 Enter the number B. P45 2 
4 Refer to the record sheet and enter the required CO line number. 
P45 2 01 N 
Example: CO line 01, enter1 0. The system will display 
N or Y to define if the LED is on or off. 
5 Refer to the System Record Sheet and change the CO line 
P45 2 01 N Y 
status as required (Y or N). 
02 N 
Press m to step to next CO line number. 
6 To Exit Program/Store Data P45 2 01 N Y 
A) To store data, press 
q . 02 N 
B) To exit this program, press1 1 
q p45 ## 
P 
TABLERM-AF 
PROGRAM45-3-6 
EQUALACCESS,SPEClALCOMMONCARRlERNUMBERSandAUTHORlZATlONCODEDlGlTLENGTH 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter 1 0 H H 
q . P 
2 Enter Program Number 45 P 45 
Press 
q . P45 
3 Refer to the record sheet and enter the item number (3 - 6). 
P45 3 NNNNN 
Example: Item 3, enter 1 . The system will display 
the present equal access number or EAl Code. 
4 Refer to the System Record Sheet and enter the required number. ~45 3 NNNNN 12345 
Example: 12345, enter 0 1 1 8 1 
q . P45 
5 Enter code number 4. The system will display present authorization ~45 4 oo 12 
code digit length. Refer to the System Record Sheet and enter 
P45 
the required authorization code number digit length. 
Example: 12, enter: 0 1 
q 
6 To exit this program, press B B q . 
p45 ## 
P 
NOTE: 
Items 5 and 6 are entered the same way as 3 and 4, respectively. 
-34A-  
						

							REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
This page intentionally left blank. 
-34B-  
						

							REMOTEADMIN &MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AG 
PROGRAM45-8-9 
TOLLRESTRICTIONOVERRIDECODE 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Program Mode >MODE PROG 
At the >MODE prompt, enter i 1 w @ 
q . P 
2 Enter the Program Number 45 P 45 
Press 
q . P45 
3 Refer to the System Record Sheet and enter 1 or 1 for the P45 8 NNNN 
desired code number. The system will display the present 
override code number. 
4 Refer to the record sheet and enter a new number if required. P45 8 NNNN 1234 
Example: 1234. Enter: 0 # Ff 1 . 
5 To Exit Program/Store Data P45 8 NNNN 1234 
A) To store data, press (9 . 
p45 ## 
B) To exit this program, press B m q P 
TABLERM-AH 
PROGRAM46-2-4 
TOLLRESTRlCTlONALLOWED/DENIEDAREACODESASSlGNEDBYCLASS 
TEP ACTION DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter i m H H 
q P 
2 Enter Program Number 46 P 46 
Press 
q . P46 
3 Enter class number (1 m 4). P46 0 
L 
Class Number 
4 Enter g,I,orIm P46 00 
l 1 -to add codes to memory (allow). c 2,3or4 
l 1 -to delete codes from memory (deny). 
l 1 m -to display codes in memory (allowed codes). ALLOW? or DENY? 
5 Refer to the System Record Sheet and enter the area code or 
P46 X Y 
area code group. Single 000. Group 1700 * nfln ALLOW 1700-000 
Press m to enter more codes. 
or DENY 
6 Press m to temporarily store data. Press 
q when 
P46 
completed. 
7 Continue returning to step 3 until all data input is completed for 
this program. 
8 
To Exit this Program 
Press 1 1 (9. 
P46 # #, 
P 
-35-