Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

							REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLE RM-AI 
PROGRAM46-6-8 
TOLLRESTRlCTlONALLOWED/DENIED OFFICECODESASSIGNED BYCLASS . 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter a B H n 
q P 
2 Enter Program Number 46 P 46 
Press 
q . P46 
3 Enter class number (1 m 4). P46 0 
L 
Class Number 
4 Enter i,I,orim P46 [7[7 
. 1 -to add codes to memory (allowed). 
1 6,7,or8 
l 0 -to delete codes from memory (deny). 
l 1 m - to display codes in memory (allowed codes). 
5 Refer to the System Record Sheet and enter the office code or P46 x Y 
office code group. Single 00[7. Group [7fln * 000 . ALLOW uun -000 
Press m to enter more codes. or DENY 
6 Press m to temporarily store data. Press 
q when P46 
completed. 
7 Continue returning to step 3 until all data input is completed for 
this program. 
8 
To Exit this Program P46 # # 
Press 1 a 
q . P . . 
>, 
. 
-36-  
						

							REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AJ 
PROGRAM46-10-40 
TOLLRESTRICTION CLASSPARAMETERS 
TEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter @ 1 m H 
q . 
P 
2 Enter Program Number 46 P 46 
Press 
q P46 
3 Refer to the System Record Sheet and enter the toll restriction 
class number (1 - 4). Then enter the number 1. P46 10 
Example: Class 1, enter 0 1. 
4 Refer to the System Record Sheet and enter the required 
P46 10 11 TABLE 1 N 
key/LED number. 
Example: Key number 11, enter 0 0 . The system will display 
the status of the key/LED. 
5 Refer to the System Record Sheet and change if required (Y or N). ~46 10 ii TABLE 1 N Y 
To access next key number, press m . 
12 TABLE 2 N 
6 To Exit Program/Store Data P46 10 11 TABLE 1 N Y 
A) To store data, press 
q . 
12 TABLE 2 N 
B) To exit this program, press1 1 (9. 
P46 ## 
P 
-37-  
						

							REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AK 
PROGRAM47 
TOLLRESTRICTIONEXCEPTION OFFICECODESASSIGNEDBYAREACODE . 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter 1 0 m 1 
q P 
2 Enter Program Number 47 P 47 
Pressm . P47 
3 Enter exception table (1 - 8) and press 0 . P47 Y 1 AREA CODE NNN 
4 Refer to the System Record Sheet and enter the required area P47 Y 1 AREA CODE NNN 714 
code and press 
q . P47 
Example: AC 714, enter 610 1 
q . 
5a 
To Add Exception Office Codes to Table 
l Enter exception table (1 - 8) and press B P47 01 
l Enter exception codes 000 or 000 1 ~~~ . Except 
l Press m to add more codes. 
l Press m (9 to store codes. Except 000 
5b 
To Delete Exception Office Codes from Table 
l Enter exception table (1 - 8) and press 1 P47 01 
l Enter exception codes ~~~ or ~~~ 1 000 . Delete 
l Press m to delete more codes. 
l Press m q to store codes. Delete 000 
5c To Display Exception Office Codes in Table 
l Enter exception table (1 - 8) and press 1 m . P47 ng 
l Press m to display more codes. Except no0 
l Press q to exit display. 
6 To Exit Program/Store Data: 1 1 q P47 Y 2 
Exceptn[70 
P47 # # 
P 
-38-  
						

							REMOTEAOMlN&MAlNTPROCEDURES 
SECTlON200-096-600 
FEBRUARY1991 
s 
TABLERM-AL 
PROGRAM48 
STATION TOLL RESTRICTION CLASSIFICATION 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Program Mode 
>MODE PROG 
At the >MODE prompt, enter 1 a m 1 
q . 
P 
2 Enter Program Number 48 P 48 
Pressm . P48 
3 Refer to the System Record Sheet and enter the required port 
P48 0 0 
number. 
Example: Port 00, enter 1 1 
4 Press 1 key. The system will display the present data as a 
P48 0 0 # 13 
2-digit code: The first digit designates digit free or digit restrict. 
The second digit is the station restriction code. Refer to the 
System Record Sheet and change if required. 
5 To Exit Program/Store Data 
A) To store data, press q 
P48 0 0 # 13 
p48 # # 
B) Continue returning to step 3 until all data is recorded for this 
P 
program. 
C) To exit this program, press 1 1 (9. 
TABLERM-AM 
PROGRAM50-1 
LCRPARAMETERS 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter i m m 1 
q . 
P 
2 Enter Program Number 50. P 50 
Press 
q . P50 
3 Enter 0 . Refer to the System Record Sheet and enter the required ~50 1 01 N 
key/LED number. 
Example: Key 01, enter1 0 . 
4 Refer to the System Record Sheet and change key/LED status, 
P50 1 01 N 
if required. 
02 N 
Press m to move to next key/LED. 
5 
To Exit Program/Store Data P50 1 01 N 
A) To store data, pressm 
02 N 
B) To exit this program, press [ 1 
q . 
p50 # # 
P 
-39-  
						

							REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AN 
PROGRAM50-2 
LCRHOMEAREACODE 
;TEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter i 0 1 H [9. P 
2 Enter Program Number 50 P 50 
Pressm 
P50 
3 Enter the number 1 . The system will display the last area code 
P50 2 NNN 
programmed. Refer to the System Record Sheet and change 
if required. 
4 To Exit Program/Store Data P50 2 NNN 
A) To store data, press 
q . 
P50 # # 
B) To exit this program, press 1 1 
q . P 
TABLERM-A0 
PROGRAM50-31-35 
LCRSPECIALCODES 
ACTION 
1 1 Enter Proaram Mode 
At the >M6DE prompt, enter i 1 m 1 q . 
2 Enter Program Number 50 
Press q . 
3 Refer to the System Record Sheet and enter 31 - 35 as required. 
Example: 31, enter 1 1. 
System will display previously programmed number. Refer to the 
System Record Sheet and change if required. 
4 
To Exit Program/Store Data 
A) To store data, press q . 
B) Continue returning to step 3 until all data for this program has 
been entered. 
C) To exit this program, press 1 1 m . 
DISPLAY/PRINTOUT 
>MODE PROG 
P 
P 50 
P50 
P50 31 NNNN 
P50 31 NNNN 
P50 # # 
P 
-4o-  
						

							REMOTE ADMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
TABLE RM-AP 
PROGRAM 50-4 
LCR LDI PLAN NUMBER 
TEP ACTION DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter-1 0 a 1 a. P 
2 Enter Program Number 50 P 50 
Press 
q . P50 
3 Enter the number 8 P50 4 1 
The system will display the present LDI route number. 
Refer to the System Record Sheet and change if required. 
4 
Exit Program/Store Data P50 4 1 
A) To store data, pressm . 
P50 # # 
B) To exit this program, press 1 1 
q P 
TABLE RM-AQ 
PROGRAM 50-5 
LCR LOCAL CALL PLAN NUMBER 
;TEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter 1 0 0 1 
q . P 
2 Enter Program Number 50 P 50 
Press 
q . P50 
3 Enter the number B P50 5 1 2 
The system will display the present local route plan number. 
Refer to the System Record Sheet and change if required. 
Example: 2, enter 1 . 
4 Exit Program/Store Data P50 5 1 2 
A) To store data, press 
q P50 # # 
B) To exit this program, press 1 B 
q . P 
-41-  
						

							REMOTEADMIN & MAINTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AR 
PROGRAM!iO-6 
LCRDIALZEROTIMEOUT 
STEP ACTION DISPLAY/PRINTOUT 
1 Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter m @ m @ 
q . P 
2 Enter Program Number 50 
Press (9 . 
3 Enter the number @ 
The system will display the present dial zero timeout. 
Refer to the System Record Sheet and change if required. 
Example: 10, enter 0 1. P 50 
P50 
P50 6 06 10 
4 Exit Program/Store Data 
A) To store data, press q . 
B) To exit this program, press B 1 
q . P50 6 06 10 
p50 # # 
P 
TABLERM-AS 
PROGRAM51 
LCRAREACODES 
;TEPl ACTION 
1 Enter Program Mode 
At the >MODE prompt, enter 1 1 1 a (9. 
2 Enter Proaram Number 51 
1 Press q -. 
3 Refer to the System Record Sheet and enter the required 
route plan number (1 w 8). 
Example: Route plan 1, enter 0. 
Enter 1, i,or I- 
. 1 - To add area codes to table. 
l B -To delete area codes from table. 
l 1 m - to display area codes in table, 
continue to press m to display more codes. 
Press 
q to exit display. 
5 
7 
Enter codes on0 or 000 1 000 and 
press m after each code entry. 
6 Exit Program/Store Data 
A) To store data, pressm 
B) Continue returning to step 3 until all data has been 
entered for this program. 
C) To exit this program, press 1 1 
q . 
DISPLAY/PRINTOUT 
>MODE PROG 
P 
P 51 
P51 
P51 1 
P51Utl - 2,3or4 
T Plan No. 
p51 uu 
nnn 
						

							REMOTEADMIN &MAlNTPROCEDURES 
SECTlON200-096-600 
FEBRUARY1991 
TABLERM-AT 
PROGRAM52 
LCROFFlCECODEEXCEPTlONSFORSPEClFlEDAREACODE 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter B 0 m a 
q . 
P 
2 Enter Program Number 52 P 52 
Pressm . 
P52 
3 Define Route Plan Number P52 10 0 3 
Refer to the System Record Sheet and enter the 
L LCR Plan No. exception table number (1 m 8). 
!- L 
Example: Table 1, enter 8. Action Code 
Enter Action code 1 . Exception Table No. 
The system will print out the currently defined route 
plan number. Refer to the System Record Sheet and 
enter 
new plan number if required. Example: Change to 3. 
4 Define Area Code Number 
Press [9 . P52 ll~tl~212 
P52 
Enter exception table number (1 - 8) defined in step 3. 
Enter Action code 0 
The system will print out the currently defined area --iI 
k 
Area Code 
Action Code 
Exception Table No. 
code number. Refer to the System Record Sheet and enter the 
new area code number if required. 
Example: Change to 212, enter 1 0 
Press 
q . 1. 
5 Display Office Codes P52 14 
Enter exception table number defined in step 3. 
Enter Action code 1 . 
Press m to dis la ooooodOOO 
5s previously selected office codes. 
Continually press 
l ’ until all previously selected T Office Codes 
codes have been displayed, then press q . 
6 
To Add 2) or Delete (3) Office Codes 
d P52 12 
Press - . 
300-325 
Enter exception table number defined in step 3. 
P52 
Refer to the System Record Sheets and enter 1 
to add office codes or 1 to delete office codes. 
Example: Add office codes 300-325 
Enter 1 (OrI )1111111m 
7 
To Exit Program/Store Data 
Data was stored when q was pressed in step 6. P52 # # A) 
P 
B) Continue returning to step 3 until all data is entered 
for this program. 
-43-  
						

							REMOTEADMIN & MAINTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AU 
PROGRAM53 
LCRSCHEDULEASSIGNMENT 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter i 1 B 1 
q . P 
2 Enter Program Number 53 P 53 
Press 
q . P53 
3 Define Route Plan Number P53 1 
Refer to the System Record Sheet and enter the route 
plan number (1 - 8). 
Example: Route Plan 1, enter 1. 
4 Define Schedule Number P53 1 1 
Refer to the System Record Sheet and enter the required 
schedule number (1 - 3). 
Example: Schedule 1, enter 0 . 
5 
Enter Code Number 0 P53 1 1 0 0000 0800 
The system will display the previously selected time for P53 
the route plan number (step 3) and the schedule number (step 4). 
Refer to the System Record Sheet and change the time if required. 
Example: Change to 0800. Enter 1 1 1 1 . 
Press 
q and repeat steps 3, 4, and 5 for all lanskchedules. 
NOTE: Enter time using 24hour format: [3 m b m . 
6 Priority Class Assignment 
P53 1 1 1 NNNN 12 
Enter the route plan number as defined in step 3. P53 
Enter the schedule number as defined in step 4. 
Refer to the System Record Sheet and enter the required 
station group number (1 - 4). 
Example: Group 1, enter 0 . 
The system will display the previously entered route definition 
numbers (reference 
Program 54). 
Refer to the System Record Sheet and enter required 
route definition numbers 1 - 4) and press 
q 
Example: Enter1 and 1 - . 
b 
Continue to repeat steps 3, 4, and 6 until all plans/schedules 
are entered. 
7 To Exit Program/Store Data P53 # # 
A) Data was stored when pressing 
q in step 6. P 
B) Continue returning to step 3 until all data is entered 
for this program. 
C) To exit this program. 
Press 1 1 
q . 
-44-  
						

							REMOTEAOMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AV 
PROGRAM54 
LCR ROUTE DEFINITION 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter i 0 m H 
q . P 
2 Enter Program Number 54 P 54 
Press 
q . P54 
3 Enter Route Plan Number P54 1 
Refer to the System Record Sheet and enter the required 
route plan number (1 - 8). 
Example: Route plan 1, enter 1. 
4 Enter Route Definition Number P54 12 11 32 
Refer to the System Record Sheet and enter the required 
route definition number (1 - 4). 
Example: Enter route definition number 2, enter 1 . 
The system will display the previously entered CO line 
group number (1 - 8) and the modified digits table number (1 - 6). 
Refer to the System Record Sheet and enter the CO line 
group and modified digit numbers as required, then press 
q . 
Example: Change the CO line grou 
modified digits table to 2. Enter: 1 
Ii number to 3 and the 
q . L !Y 
Modified Digit Table No. 
CO Line Group No. 
Route Definition No. 
Plan No. 
5 To Exit Program/Store Data P54 12 11 32 
A) To store data, press q P54 ## 
B) Continue returning to step 3 until all data has been entered P 
for this program. 
C) To exit this program, press 1 1 
q . 
-45-