Starplus Triad S System Programming Manual

							11-4 I ntro ductio n
In it i al iz e Sy st em  Pa ra m et er s
Pro g ram mi ng  S te ps
1. Press the SYSTEM  PARAMETERS  flexible button ( FLASH 80, 
Bu tton #1).  The  fo ll owing  mes sag e d is pla ys:
2. Press the HOLD  button. A confirmation tone is heard.
Des crip ti on
The System  Parameters  may  be initialized setting  all  data fields to their 
original, default values.  The following  data fields are returned to their 
default  values upon  initializing the System  Parameters.
INITIA LIZE   S YS    PARAM
P RE SS   HO LD 
						

							Introduction 11-5
Table 11-1: Syste m Paramete r Defa ults
Program 
CodeFl ex
ButtonFe aturesDef ault V alue
(after initialization)
FLASH 01
SYSTEM TIMERS
1 System  Ho ld Rec all Ti mer 060  sec
2 Exc lusi ve H ol d  Recal l Tim er 180  sec
3 Atten da n t R eca ll  Timer 01 m in
4 Tran sfer Rec all T imer 045  sec
5 Preset For ward Tim er 10 sec
6 Call For ward No/Answer Timer 15 sec
7 Pause Tim er 2 sec
8 Cal l Park Rec all Ti mer 180  sec
9 Conference/DISA Timer 10 min
10 Pagin g  Time-o ut  Tim er 15 sec
11 CO R in g Detec t Ti mer 3=300  ms
12 SLT DTMF Rec eiver Ti mer 20 sec
13 Messag e Wait  Rem in der  Ton e 000  min =Di sabl ed
14 SLT H oo k Fl ash Ti mer 10=1 sec
15 SLT H oo k Fl ash Debou nc e Timer 300  ms
16 SMDR  Ca l l Qu al ific a tio n Ti mer 30 sec
17 Auto ma ti c C a ll  Ba ck  Tim er 03 sec
18 Remi nder R in g Ti mer 00 sec
20 Flexible Inter-Digit Timeout 5 sec
FLASH 02
ADDI TIONA L SY STEM  TIMERS
1 Repeat Redial  Timer 60 sec
2 Atten da n t D isp la y  Timer 01 sec
3 Ca l l C ov era ge R in g  Timer 5 sec
4 Modem Answer  T / O 25 sec
5 Pul se Di al In ter- Di git  Tim er 300  ms
6 Pro gramm abl e DTMF Ti me Operatio n 1=100m s 
						

							11-6 I ntro ductio n
FLASH 05SY STEM FEATURES 1
1 Atten dan t Overr ide D isabl ed
2 Ho ld Preference Syst em
3 Ext ernal  Ni ght R ing Disabl ed
4 Exec uti ve O ver rid e Warn in g Ton e Enab led
5 Page Warning  Tone Enabled
6 Background Music Channel Enabled
7 Least Cost Rout ing Disabl ed
8 Acc ount Codes -  Forced Disabl ed
9 Gro up  L isten in g D isa bl ed
1 0 Id le  S p e a ke r  M od e D is a bl e d
11 Call Cost  Display Feature Disabled
12 Musi c-On -Ho ld Enabled
13 Ca l l Qua l ifier  Ton e Op tio n D isa bl ed
FLASH 06
SY STEM FEATURES 2
1 Barge-In Tone  Enabled
2 CO Ring Tones Enabled
3 Verifi ed Ac co un t C od es D isa b led
4 Call For ward Display Enabled
5 E xt e rna l  Da y  Ri ng D is a b le d
6 Over flow Station Forward Disabled
7 Di rec t Tr ansfer Mo de Enabl ed
8 Statio n I D  Lo ck D isab led
9 LCR Call  Progress Enabled
10 One-To uc h  Reco rd in g Wa r nin g  Ton e En a bl ed
11 Ringbac k on  Transfer Disabled
12 ACD Ag ent  Rec al l Disabled
13 911 Feat ure Disabled
14 Enahn ced 911 Disabled
15 VMID Station Numbers STA Numbers = VMIDTable 11-1: Syste m Paramete r Defa ults
Program 
CodeFl ex
ButtonFe aturesDef ault V alue
(after initialization) 
						

							Introduction 11-7
FLASH 07FLASH RATES 
1 In co min g CO Lin e Ri ng in g Red 480 i pm  flut ter
2 In co min g I nt erco m R in gin g Red 120 i pm  flut ter
3 Call For ward Button Red Steady On
4 Message Wait /VM Butto n Red Steady On
5 Message CallB ack – DSS/BLF Red 120 i pm  flut ter
6Do Not Disturb – DSS/BLF Red 60 ipm Dbl Wink
7 Auto  C a llB ac k  – DSS/ BLF Red 120 i pm  flash
8 UCD Available/Unavailable – DSS/BLF Red 60 ipm Dbl Wink
9 Tran sfer CO  Rin gi ng Red 120 i pm  flash
10 Rec al l CO Ri ng in g Red 480 i pm  flut ter
11 Queued CO Ri nging Gr een 48 0 ipm fl utt er
12 Exc lusi ve H ol d Gr een 12 0 ipm fl ash
13 System  Ho ld Red 60 i pm Dbl  Wi nk
14 In Use Hold (I-Hold) Green 60 ipm flash
15 Cam p-On  Bu tto n Red 120 i pm  flash
16 Cal l Bac k  But to n Red 120 i pm  flash
17 Li ne Qu eue B ut ton Red 480 i pm  flut ter
18 Do Not Disturb Button Red Steady On
19 In terco m H ol d B ut ton Re d 15  ipm flash
FLASH  09 1-6 MOH Assi gn men ts N on e
FLASH  10 -- Atten dan t Stati on  Assig nm ent STA 10 0
FLASH  11 1-4  System  Tim e And Dat e MMM/ DD/Y Y,
12-hr  di spl ay
FLASH 12 -- PBX Diali ng Codes None
FLASH  13 1-4 Exec uti ve/ Secret ary Pairs N on e
FLASH  14 1-6 On-B oard Rel ay  N on eTable 11-1: Syste m Paramete r Defa ults
Program 
CodeFl ex
ButtonFe aturesDef ault V alue
(after initialization) 
						

							11-8 I ntro ductio n
FLASH 15BAUD RATE ASSIGN MEN TS
1 Por t #1 (1st  RS-232C po rt  on  Opt ion al MI SU) 9 600 Bau d
2 Por t #2 (2n d R S-232C por t on  Optio nal MI SU) 9 600 Bau d
3 Por t #3 (Optio nal  Modem) 9 600 Bau d
FLASH  16 1-3 Net wor king  Tables N on e
FLASH  20 1 DI SA Acc ess Co de 100
2 Database Admin Password 322 6
FLASH 21 1 SMDR Enable/Disable No
2 Long Distance/Local Assi gnment Long Distance
3 Charact er Pr int  Assignm ent 80
4 Baud R at e Displ ay 960 0
5 SMDR  Por t Assi gnments Por t #1
FLASH 22 1 Automatic/Manual Operation Manual
2-8 Da y  of  Week  Pr og ra mmi ng Ma n ua l= N on e; Au to =
M-F 08:00 1 7:00
Sat-Sun ##: ## ##: ##
FLASH  23 1-4 Di rec tor y  Di al in g Tabl e N on e
FLASH  30 1-1 2 Hu nt  Gro up N on e
13 S ta tio n/ Pil ot/ Pi lot  Ri ng  All --Hu nt ing  
AssignmentsPi lot
FLASH  31 1 Verifi ed  Ac co un t C od e En try N on e
2COS None
FLASH  39 1-2 4 CO G rou p Queu ing En abl ed
FLASH  41 1 Di al  Pu lse Paramet ers 6 0/40,  10 ppsTable 11-1: Syste m Paramete r Defa ults
Program 
CodeFl ex
ButtonFe aturesDef ault V alue
(after initialization) 
						

							Introduction 11-9
In iti al iz e CO  Lin e A ttr ibu tes
Pro g ram mi ng  S te ps
1 . Pr es s t he  CO  LI NE  ATT R IBU TES  fl ex ibl e  but ton  (FLASH 80, 
Bu tton #2).  The  fo ll owing  mes sag e d is pla ys:
2. Press the HOLD  button. A confirmation tone is heard.
Des crip ti on
The CO Line Parameters may be initialized setting all data  fields to their 
original, default values.  The following  data fields are returned to their 
default value upon initializing the CO Line Attributes.
INITIA LIZE   CO   LINES
P RE SS   HO LD
Table 11-2: CO Line Attribute Defaults
Pr o g r a m 
Co d eFlex
ButtonFeat uresDef ault Va lue
( a ft er  in i t ia li z at i on )
FLASH 40
PA G E  A1 D TMF/ D ia l Pu lse Pr og ra mmi ng D TM F
2 C O/ PB X P rog ra mm ing CO
3 UN A Pr og ra mmi ng Ena b led
4 DISA CO-to-CO Enabled
5Privacy Enabled
6 Loo p Su per visio n  Prog ramm in g 4=400 m s
7 D IS A Pr og ra mmi ng No ne
8 C O  Li ne G rou p  Pro gra m min g Gr ou p 1
9 C la ss of Ser v ic e (COS) Pro gra m min g COS 1
10 CO  Line Ringing Assignments (blank)
1 1 C O  Li ne I den tifi ca ti on  Di spl ay L ine  XX X
12 Trunk Direction Bothway
1 3 Display Ring Assignments None
1 4 DID/TIE Signal Type Wink
1 5 911 Tru nk Disabl ed 
						

							11- 1 0 I ntr o ducti o n
Initialize Station Attributes
Pro g ram mi ng  S te ps
1 . Pr es s t h e  STATI ON  AT TR I B U TE S f le x ib le  bu t to n  (FLASH 80, 
Bu tton #3).  The  fo ll owing  mes sag e d is pla ys:
2 . To ini t ia li ze  t he St at ion At t ri but es,  pr es s t he HOL D b utt on. A 
conf irmation  ton e is  hea rd.
Des crip ti on
The Station Parameters may be initialized setting all data  fields to their 
original, default values.  The following  data fields are returned to their 
default value upon initializing the Station Attributes.
FLASH 40
PA G E  B1 Tr an smi t Vo lu me Op tio n 5 (0 d b )
2 Preset  Cal l For ward Dest inat ion ####
3 Preset  Forw ar d Voic e Mail ####
4 Universal Day Answ er Disabl ed
5 Mu sic-On -Ho ld  p er C O Li ne C ha n nel  1
6Ring Tone 00
FLASH 40
PA G E  C1 Fla sh Ti mer  Prog ra mm in g 10
2 Ri ng  D ela y  Timer 10
3 Resei ze Tim er 200 m s
4 Gu a rd  Timer 05 sec
5 Preset  Fo rw ar d Ti mer 10 sec
INITIA LIZE   S TATIONS
P RE SS   HO LD
Table 11-2: CO Line Attribute Defaults
Pr o g r a m 
Co d eFlex
ButtonFeat uresDef ault Va lue
( a ft er  in i t ia li z at i on ) 
						

							Introduction 11-11
Tabl e 1 1- 3:  St at io n At t ri but e Def ault s
Progra m 
CodeFl ex
ButtonFeat uresDef ault V alue
( after initialization)
 FLASH  50 1 Pag in g Ac cess En abled
PAGE A2Do Not Disturb Enabled
3 Conference Enable/Disable (Per Station) Enabled
4 Ex ecu tive Overri de D isab led
5 Pr ivacy (Per Stat ion) Enabled
6 System Speed Di al Ac cess En abled
7 Line Queuing Enabled
8 P r e fe r r e d  L i ne   A ns w e r En a b l e d
9 Off-Hoo k  Voic e Over (OHVO) Disabled
10 C a ll Fo rwa rd in g En a b led
11 Forc ed  Lea st C o st Ro ut in g ( LC R ) D isa b led
12 ACD  Sup ervi sor Mo n ito r w/ Barg e-In D isab led
13 Ex ecu tiv e Ov erri de  Blo ck D isa b led
FLASH 50
PAGE A14 C O Li ne R in gi ng D isa b led
15 N a me/N um ber  D isp la y a t  Id le N a me ( Ena b led )
16 ACD Zap Tone Disabled
17 C O  Lo op  Po ol  Fl ex D is a b led
18 Admi nist ration Access Disabled 
						

							11- 1 2 I ntr o ducti o n
FLASH 50
PAGE B1 Stat ion  Id en tific atio n 0 06 (24-Bt n K ey set )
6 (SLT w/ o MW t)
2 Stat ion Day Class of Service 1
3 Stat ion  N ig ht Cl ass o f Servi ce 1
4 Speaker phone/Headset  Pro gram ming 0=Ful l Speaker phone
5 Pick-Up Group(s) Programming 1
6 Pa g in g Z on e(s) P rog ra mm ing 1
8 CO Li ne G ro up Acc ess 1
9 LCR  Class of Ser vice  (COS) 0
10 Off-Hoo k  Preference Pro grammi ng 00 (Keyset)
11 Flex ib le B ut ton  Pro gr am min g (b la nk )
12 K eyset  Mode Inact ive Mode
13 Vo ic e Ma il I D  Tra n sla tio n X XX X (St at io n #)
14 Display Flexible Buttons None
17 C or dl ess Key  Bu tto n 0 0
FLASH 50
PAGE C1 I nter na l  No  Answ er D estin a tio n N on e
2 I nte r na l Bus y  D e s ti na ti on N on e
3 Ex tern a l N o A nswer  Dest in at ion N on e
4 Ex tern a l B usy  D estin a tio n N on e
5 No Answer  Timer 10 sec
6 Speed Di al  Acc ess NoneTabl e 1 1- 3:  St at io n At t ri but e Def ault s
Progra m 
CodeFl ex
ButtonFeat uresDef ault V alue
( after initialization) 
						

							Introduction 11-13
Initialize CO / Station Port Parameters
Pro g ram mi ng  S te ps
1. Press the PORT-STA/CO  flexible button ( FLASH 80, Butto n #4 ). The  
following message displays:
2. To initialize the Station/CO Port Parameters, press the HOLD button. A 
conf irmation  ton e is  hea rd.
Des crip ti on
St at ion  numbe rs  c an  be  in it ia li ze d a nd r es et  t o t he ir  or igi nal  de faul t  
val u es  af te r  the  u s er  has  pe r fo rm ed  the  S tat i o n R e lo c at i o n Fe at u re  (6 3 6).
Initialize Exception Tables
Pro g ram mi ng  S te ps
1 . Pr es s t he  EXC EP TI O N TABL ES  fl exi ble  b utt on ( FLASH 80, Butto n #5 ). 
The following  message displays:
2 . To  ini t ia li ze  t he  Exc ep ti on Tab le s, p re ss  the  HO LD  but ton . A  
conf irmation  ton e is  hea rd.
Des crip ti on
The  E xcept i on Ta bl es  Para met e rs , i nclud ing  the  Al low/De ny T abl es  an d 
the Special Tables, may be initialized setting all tables to their  original, 
def aul t val ues .
The following Tables are cleared returning to their default value upon 
initializing the Exception Tables  parameters:
INITIALIZE   PORT   -   STA   /   CO
P RE SS   HO LD
INITIA LIZE   E X   TABLES
P RE SS   HO LD