Starplus Triad S System Programming Manual

							2-44 Prog ra mmable Flash  Rat es
In co mi ng  In t erco m  R in g in g
Pro g ram mi ng  S te ps
1 . Pr es s t he  I NC  IC M  R IN G fl ex  but ton (FLA SH 07 ,  Bu tton  #2). The 
following message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
t he  2 9 avai la ble  opt i ons. Refe r to Ta b l e  2 - 6 :  F l a s h  R at e s.
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The  Incoming Inte rco m Ringing  flash  ra te  is the  ra te  a n Incoming  DS S 
but ton  fl ashe s i f  you ha ve  a D SS  app ear ance  for  t he  cal li ng s ta ti on.  Thi s 
flash  rate can  be  programmed to 29  different options  identified in the 
flash rate table. This enables the programmer to customize the key 
sys te m conf igur at ion  to  de sir e d fl as h r ate s.
By default, the Inco ming  Intercom  Ringing  flash rate  is set for RED 
12 0 i pm F lu t t er  (1 1).
Call Forward  Butto n
Pro g ram mi ng  S te ps
1. Press the CALL FORWARD BTN  flex button ( FLASH 07, Butto n # 3). 
The following  message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
INC  IC M  RING 0 0-2 8
RED  120  IPM  FLUTTER
CAL L F ORWARD  BT N 0 0-2 8
RED  STEADY  ON 
						

							Program mable Flash  Rat es 2 -45
Des crip ti on
The Call Forward  Button flash rate  is the  rate at which the  Call Forward 
but ton  fla she s whe n any  typ e of  forwa rd  mode  is  use d. T his  fla sh r at e ca n 
be  pr ogra mme d t o 2 9  dif fer en t  opti ons  id ent if ie d i n t he  fl ash  ra te  t abl e.  
Thi s enab le s t he  pr ogr amme r to cust omiz e  t he key sys te m confi gur at ion 
to  desired flash rates. By  default,  Call  Forward Button flash rate is  set for a 
Red  St ea dy O n (0 1 ).
Message Wait / VM Button
Pro g ram mi ng  S te ps
1. Press the MSG  WAIT/VM BTN  flex b utton ( FLASH 07, Butto n #4). T he 
following message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The  M es sag e W ai t/ VM  B u t t o n fl ash  ra te  i s  the  r at e a t  whic h  th e M e ssa ge 
Wai t  and  VM but t on(s)  fla she s w hen  you r ece iv e a  me ssa ge/ voi ce  mai l 
message.  This flash rate  can be programmed  to  29 different options 
identified in the  flash  rate table.  This  enables the programmer  to 
cust omiz e  t he key sys te m conf igur at ion to de sir e d fl ash  r ate s.
By default, Message  Wait/VM Button flash rate is  set for  a Red Steady  On 
(01).
MSG WAIT  / VM BTN 0 0-2 8
RED  STEADY  ON
Th e fix ed me ssa ge bu tton shou ld no t be use d as a  V oic e Mail  b utton . 
						

							2-46 Prog ra mmable Flash  Rat es
Me ss age  Callback -  DS S / BLF
Pro g ram mi ng  S te ps
1 . Pr es s t he  MSG  CBCK –  DSS /BL F fl ex  but ton  (FLASH  07, Button  #5). 
The following  message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The  Mes sag e C al l  Back D SS/BLF  fl ash  ra te  i s t he  r at e a t  which  a D SS  
but ton  of a  st at io n r et urni ng  your  mes sag e f las hes . T his  fl as h r at e ca n be  
pr ogra mmed  to  29  di ffe re nt  opti ons  ide nt ifi ed  in t he  fl ash r at e  tab le . T his  
ena ble s  the  pr ogr amme r  t o cust omi ze  t he  key  sys te m conf igur at io n t o 
des ir ed  fl ash  ra te s.  By de fau lt , Me ssa ge  Cal lb ack D SS /BLF  fl as h r at e i s  set  
for a  Red 120  ipm Flutter  (11).
Do Not Disturb  - DSS / BLF
Pro g ram mi ng  S te ps
1 . Pr es s t he  DN D – DS S/ BLF  fl ex b utt on ( FLASH 07, Bu tton  #6). The  
following message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
MSG CBCK / DSS  / BLF 0 0-2 8
RED  120  IPM  FLUTTER
DND  DSS  / BLF 00-28
RED  60  IPM  DBL  WINK 
						

							Program mable Flash  Rat es 2 -47
Des crip ti on
The Do No t Disturb DSS/BLF flash rate is the rate at which a  DSS button of 
a s ta ti on f las hes  whe n you  ar e i n a  Do  Not  Di st urb  mode .  Thi s f las h r at e 
c an b e p rogr am med  to  29  d iff er ent  opt i ons i de nti fi ed  in  th e f la sh r at e 
ta bl e. Thi s e nab le s t he  pr ogra mme r to cu st omiz e th e k ey syst e m 
configura tion to d esired  fla sh rates . By  de fault,  Do  Not Disturb  DS S/BLF 
flash  rate is set for a  Red  60 ipm  Double  Wink (04).
Au t o C al lb a ck  - D SS  /  B L F
Pro g ram mi ng  S te ps
1 . Pr es s t he  AU TO  CBCK – DSS/BLF flex  button (FLASH  07, Bu tton  #7). 
The following  message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The Auto Callback  DSS/BLF flash rate  is the rate  at which a  DSS button of 
a s ta tion returning  your call  back  flashe s.  This  fla sh rate  can b e 
pr ogra mmed  to  29  di ffe re nt  opti ons  ide nt ifi ed  in t he  fl ash r at e  tab le . T his  
ena ble s  the  pr ogr amme r  t o cust omi ze  t he  key  sys te m conf igur at io n t o 
desired flash rates. By default, Auto Callback DSS/BLF flash  rate is set for a 
Red  120 ipm Flash (10).
UCD Available / Unavailable - DSS / BLF
Pro g ram mi ng  S te ps
1. Pres s the  UC D UNAV L – DS S/ BLF  fle x b utt on ( FLASH 07, Butto n #8 ). 
The following  message displays:
AUTO  C BCK  DSS / BLF 00-28
RED  120  IPM  FLASH
UCD  UNAVL  DSS / BLF 00-28
RED  60  IPM  DBL  WINK 
						

							2-48 Prog ra mmable Flash  Rat es
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The UCD Available/Unavailable DSS/BLF flash rate is the rate at  which  a 
DSS  ap pea ra nce f or a  st at ion  in  AC D/UCD  Unav ai lab le  mode  fl as hes . Th is  
flash  rate can  be  programmed to 29  different options  identified in the 
flash rate table. This enables the programmer to customize the key 
sys te m conf igur at ion  to  de sir e d fl as h r ate s.  By d efa ult , U CD
Av ai lab le /Unava il abl e  DSS /BLF f la sh r at e  is  se t  for  a  Re d  60  i pm D oubl e 
Wink (04).
Tr an s f e r  C O  R i n g i n g
Pro g ram mi ng  S te ps
1 . Pr es s t he  TR A NSF ER  CO  R IN G fl ex b utt on ( FLASH 07, Bu tton  #9). The 
following message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The  Tr ans fer  CO  Ri nging  fla sh r at e i s t he  rat e  at  which  a CO  Li ne b utt on or  
Loop  button  flashes when a call  is transferred to you.  This  flash rate  can 
be  pr ogra mme d t o 2 9  dif fer en t  opti ons  id ent if ie d i n t he  fl ash  ra te  t abl e.  
Thi s enab le s t he  pr ogr amme r to cust omiz e  t he key sys te m confi gur at ion 
to  desired flash rates. By  default, Transfer CO Ringing  flash rate is  set fo r a 
Red  120 ipm Flash (10).
TRANS FER  CO  RING 00-28
RED  120  IPM  FLASH 
						

							Program mable Flash  Rat es 2 -49
Recall CO Ri nging
Pro g ram mi ng  S te ps
1. Press the RECALL CO RING flex button (FLASH 07, Button  #10). T he 
following message displays:
2. Enter a valid number on the dial pad to correspond  to  one  of the 
29 ava ilable  options . (Refer to Tab l e 2- 6: Fl as h R a tes.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates
Des crip ti on
The  Re ca ll C O  Ringing f las h rate  is  th e rate  at which a  CO Line  button  or 
Loop  but ton  fla she s whe n a  cal l  re cal ls  to  your  st at ion . T his  fl ash  ra te  can 
be  pr ogra mme d t o 2 9  dif fer en t  opti ons  id ent if ie d i n t he  fl ash  ra te  t abl e.  
Thi s enab le s t he  pr ogr amme r to cust omiz e  t he key sys te m confi gur at ion 
to  des ir ed  fl ash  ra te s.  By de fau lt , Re cal l C O  Ringi ng  fla sh r at e  is  se t  for  a 
Red  480 ipm Flutter (08).
Queued CO Ri ngi ng
Pro g ram mi ng  S te ps
1 . Pr es s t he  QU EUED  CO  RIN G fl ex  but ton ( FLA SH 07, Butto n #11 ). The  
following message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
RECAL L  CO  RING 0 0-2 8
RED  480  IPM  FLUTTER
QU EU ED CO R IN G 0 0-2 8
GREEN  480  I PM  FLUTTER 
						

							2-50 Prog ra mmable Flash  Rat es
Des crip ti on
The  Qu eue d CO  Ring ing f la sh r at e i s t he r at e  at  which a  CO  Li ne b utt on or  
Loop  but ton  fla she s wh en a  que ued  li ne  be comes  av ail ab le . T his  fl ash  
ra te  c an  be  pr ogra mme d t o 2 9  dif fer en t  opti ons  id ent if ie d i n t he  fl ash 
rate table. This  enables  the programmer to customize the  key system 
configura tion to d esired  fla sh rates . By  de fault,  Qu eue d C O Ringing flas h 
rate is set for a Green 480 ipm  Flutter (22).
Excl us ive  Ho ld
Pro g ram mi ng  S te ps
1 . Pr es s t he  EXC LU SI VE H OLD  fl ex  but ton (FLASH 0 7,  Bu tton  #12). The 
following message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The  Excl usi ve  Hold  fla sh r at e i s t he r at e a t wh ich a  CO L ine  but ton  or Loop  
but ton  fl ashe s w hen  a cal l  is  pl ace d on  Excl usi ve  Hol d. T his  fl as h r at e ca n 
be  pr ogra mme d t o 2 9  dif fer en t  opti ons  id ent if ie d i n t he  fl ash  ra te  t abl e.  
Thi s enab le s t he  pr ogr amme r to cust omiz e  t he key sys te m confi gur at ion 
to  des ir ed  fl ash  ra te s.  By de fau lt , E xclus iv e H old  fla sh  rat e  is  s et  for  a 
Green 120 ipm Flash (24).
Sys te m Ho ld
Pro g ram mi ng  S te ps
1 . Pr es s t he  SY S TE M  HOL D fl ex  but ton  (FLASH 07, Button  #13). T he 
following message displays:
EXCLUS IVE H OLD 0 0-2 8
GREEN  120  I PM  FLASH
SY ST EM H OLD 0 0-2 8
RED  60  IPM  DBL  WINK 
						

							Program mable Flash  Rat es 2 -51
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The  S yst em  Hold  fl ash  ra te  i s t he  r at e a t  which  a C O  Lin e b utt on or  L oop 
but ton f la shes  whe n a cal l i s pl ace d on S yst em H old.  Thi s fl as h ra te  can be  
pr ogra mmed  to  29  di ffe re nt  opti ons  ide nt ifi ed  in t he  fl ash r at e  tab le . T his  
ena ble s  the  pr ogr amme r  t o cust omi ze  t he  key  sys te m conf igur at io n t o 
des ir ed  fl ash  ra te s.  By de fau lt , S yst em  Hol d fl as h r at e i s  se t f or  a Re d 
60 ipm Double Wink (04).
In -Use  Hold  (I-Hold )
Pro g ram mi ng  S te ps
1 . Pr es s t he  I N-US E  HOLD  fl ex  but ton (FLASH  07, Bu tton  #14). T he 
following message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The  In Use -Hold (I-H old)  fla sh rate is  the  rate  at which a  CO  Line  button or 
Loop  button  fla shes wh en a  call  is  placed on  In- Use Hold (I-Ho ld).  Th is 
flash  rate can  be  programmed to 29  different options  identified in the 
flash rate table. This enables the programmer to customize the key 
sys te m conf igur at ion  to  de sir e d fl as h r ate s.  By d efa ult , I n- Use  Hol d 
(I- Hold) flas h rate is  se t  for  a Gre en 60 ipm F la sh (17).
I N -U SE   H O L D 0 0-2 8
GREEN  60  IPM  FLASH 
						

							2-52 Prog ra mmable Flash  Rat es
Camp-O n Butto n
Pro g ram mi ng  S te ps
1 . Pr es s t he  CAMP-O N BT N fl ex  but ton (FLASH  07, Button  #15). T he 
following message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The  C amp- On  Button f las h rate  is  th e rate  at which the  Camp -On Button  
flashe s wh en y ou receive  a  Camp -On. T his  flash  ra te  can  be  prog ram med  
to  29 different options identified in the flash rate  table.  This enables the 
programmer to customize  the key system configuration to desired  flash 
ra te s.  B y de fau l t , C amp- On  B u tt o n f la sh r at e  is  se t  fo r  a  Re d 1 2 0  ip m 
Fl ash (12 ).
Call B ac k Butto n
Pro g ram mi ng  S te ps
1. Pres s the CALL  BAC K BTN  flex  button ( FLA SH 07 , Bu tton #16). The 
following message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
CAM P ON BT N 0 0-2 8
RED  120  IPM  FLASH
CAL L  BACK  BT N 0 0-2 8
RED  120  IPM  FLASH 
						

							Program mable Flash  Rat es 2 -53
Des crip ti on
The Call Back Button  flash  rate is the  rate at which the Call Back  Button 
fl ashe s w hen  a s tat i on at  wh ich  you l eft  a  cal l  back  re ques t  be com es 
ava il abl e.  Th is fl ash ra te  can be pr ogra mmed  t o 2 9 dif fer ent  op ti ons 
identified in the  flash  rate table.  This  enables the programmer  to 
cust omiz e  t he k ey  syst e m confi gur at ion  to d es ir ed  fla sh r at es . By  def aul t, 
Cal l  Back  Bu tt on fl as h r at e i s  se t  for  a Re d 1 2 0  ipm  Fl ash  (1 0).
Li ne  Queue Butto n
Pro g ram mi ng  S te ps
1 . Pr es s t he  LI NE QUE UE BTN fle x bu tt on ( FLASH 07, Butto n #1 7). The  
following message displays:
2. Enter a valid number (00-28) on the dial pad to correspond to one of 
the 29  available options.  (Refer to Ta b l e  2 - 6 :  F l a s h  R at e s.)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The Line  Queue Button  flash rate  is the  rate at which the Line  Queue 
Button f la she s af te r  que ueing onto a  bus y line . T his b utton f las hes  whe n 
the busy line becomes available. This flash rate can be programmed to 
29 different options identified in the flash rate  table which enables the 
programmer to customize  the key system configuration to desired  flash 
rates.  By default, Line Queue Button  flash  rate is set for a  Red  480 ipm 
Fl utt e r ( 08 ).
Do Not Disturb  Button
Pro g ram mi ng  S te ps
1 . Pr es s t he  DN D BT N fl ex  but ton (FLASH  07, Bu tton  #18). T he 
following message displays:
LIN E  QU EU E  BT N 0 0-2 8
RED  480  IPM  FLUTTER
DND  BTN 00-28
RED  STEADY  ON