Starplus Triad S System Programming Manual

							3-30 I CLI D  Prog ra mming
2. Enter a valid number (0–3) which corresponds  with the  following 
entries:
[0] =  60/40 ( RAT IO),  10 p ps  (SPEE D)
[1] =  66/33 ( RAT IO),  10 p ps  (SPEE D)
[2] =  60/40 ( RAT IO),  20 p ps  (SPEE D)
[3] =  66/33 ( RAT IO),  20 p ps  (SPEE D)
3. Press HOLD to save the entry. A confirmation  tone is  heard  and the 
display updates.
Des crip ti on
The Dial Pulse option  lets the  installer adju st the dial pulse ratio and 
speed when using  dial  pulse  (rotary) type signaling.  By default,  all lines 
ar e D TM F  (t one)  si gnal ing.  I f pu lse  di al in g i s r eq uir ed,  t he  ind ivi dual  
outs id e l i ne m ust  be  pr ogr amme d f or  Dia l  Pu lse  (D P ).
Whe n Di al  P ul se  is  se le c t ed,  th is  sys te m-wi de  pa ra met er  mus t  be  se t  to 
det e rmi ne  th e b re ak/ mak e r at i o and  th e d ial  s pee d of  t he  dia l  puls e 
si gnal .
ICLID Programming
ICLID Ringing  Assignments
Pro g ram mi ng  S te ps
1. Press FLASH and  di al  [43 ].  The following message displays:
00 0 = Ro u t e N u mb er  ( 00 0–499 )
XXX =  Ringing  Destination
Y = R i n gi n g  T y pe
Th is  pro gram  code  is  on ly  us ed  whe n an  outs id e (C O) l ine  is  p rogra mmed  
for Di al Pulse.
ROUT E  00 0   XXXXY 
						

							ICL ID Programming 3 -31
2 . Pr es s t he  RI NG ASS IGN MENT  fl exi bl e  butt on (FLA SH 43 , Bu tton #1). 
LED  #1 is lit indicating  Route 000 is  ready  for programming.
3 . Ent er  a va li d De st ina ti on (XX X) and  R ing t yp e ( Y )  foll owed  by HO LD. A  
conf ir mat ion  ton e i s hea rd and the  di spl ay updat e s.
Des crip ti on
IC LI D Ri ngin g A ssi gnme nt s l et  you  change  t he r i ng as si gnme nt  base d on 
the incoming number received. This  feature permits you to  select  from 
500 ringing route s for ea ch entry in  the  name  to numbe r tra nslation tab le  
and  DID table (Flash 55). For example, this feature could be  used to 
re rou te  se le cte d  cus to mer s t o a  sp eci fic  AC D or  UC D  group  and  byp ass  
the  ge ne ral  A t te ndan t.  The  Di r ec t  I nwar d D ial i ng (D ID ) fe at u re  pe rm it s 
one- way  dir e ct  i nwar d  dia li ng a cce ss  t o st at io ns on  spe cif ic D ID  l ine s 
from th e pub lic telephone network, w ithout going  through a n Attend ant 
answering  position. DID  capabilities  refer to incoming calls only. The 
sys te m a cc e pt s 3 -7  d igi t s fr om  the  C ent ra l  Off ic e . T his  le t s t he  name  a nd 
number field of the LCD display on a DID call be presented to the ICLID 
por t.  Cal l s a re  id ent if ie d i n t he  SM DR  f ie ld  as  answ er ed  (I)  or  Unans wer ed 
(U) f oll owed  by  a D ID  numbe r. At le as t  one  DTMF  re cei ve r  must be  
ins ta ll ed .
Table 3-8: ICLID Ringing As signments
Va lid 3-Digit Destinations (X XX) Va lid Ring Types  (Y)
[020- 999] = Syst em Speed  Bin s 1020–1 999, 
for Off-Net Ri nging[0] = No Ring; unassigned; or to delete a st ation
[100- 131] = 
E xt e ns io n  Nu mb e rs [ 1]  =  Da y  Ri ng [ D]
[440- 447] = Vo ice M ai l G rou ps 1–8[2] = Night Ring[N]
[450- 457] = Hu nt  Gr ou ps 1–8[3] = Day/Night Ring[DN]
[499] =  Di rect  Ri ng in g t o Mo dem [4] = Spec ial On ly [S]
[550- 565] = ACD G ro ups 1–16 [5] = Day/Special [DS]
[550- 557] = ACD G ro ups 1–8[6] = Night/Special[NS]
[7] = All Modes [Day/Night /Special [A ]
Al l p rev iou sl y  prog ramme d r oute s  will  b e  los t wh en  up grad ing  from  FP2 
to FP3. 
						

							3-32 I CLI D  Prog ra mming
View ICLID Ringing Assignments
Pro g ram mi ng  S te ps
1 . Pr es s  F LA SH 4 3 , But ton # 17  t o di spl ay r i ng as si gnment s.  As si gnme nts  
are displayed  in  sets  of six, up  to  the number programmed. Press 
FLASH  43,  Button # 17  additional times  to  cycle to the nex t  group  of 
si x r ing  as sig nment s.
DDD = Destination
RR :
[0 ] = N o R i ng
[D ]  =  D a y  R i n g
[N ]  =  N i g ht   R i ng
[DN] = Day/Night Ring
[S]  = Speci al Only
[DS]  =  Da y/Sp ecial
[N S]  =  N i g h t/ S pe c i a l
[A]  = All Modes (Day/Night/Special)
Mult ip le  st at i on as si gnmen ts  ar e a ccompl ish ed  by a ssi gni ng an othe r 
des tination with ring status , D DDR, and pre ss ing HOL D. T his  can be 
done  for  up  to  the  ma ximu m numb er  of  stati ons  on the  sys te m.
RINGING
ASSIGN MENTS
=1Q=2W=3E=4R
=5T=6Y=7U=8I
=9O=10 P=11 A=12 S
=13 D=14 F=15 G=16 H
DISPLAY RINGING
ASSIGN MENTSNEXT ROUTE
NUM BERPR EV IOU S RO UTE
NUMBERSELECT RO UTE
NUM BER
=17 J=18 K=19 L=20 ;
=21 Z=22 X=23 C=24 V
ROUT E   000   DDDRR   DDDR
DDDR   DDDR   DDDR   DDDR 
						

							ICL ID Programming 3 -33
Ring  as sig nments  are continuous a nd d is pla y in order of  the  
des ti nati on numb er  fr om 020- 557.  A ma ximum  of  ei ght  stations  
di spl ay.  A ddi ti onal  st at i ons a nd r i nging  as sig nment s  ar e d isp lay ed 
using Button #17.
Advancing to the  Next  Route
Press the NEXT flexible button (FLASH 43 , Butto n #18) to  a dvanc e  t o  the  
next ICL ID  Route  num ber.
Returning to a Previo us R oute
Press the PREVIOUS flexible button ( FLASH 43, Butto n #1 9) to return to 
the previous ICLID  Route number.
Sele cti ng a  Di fferent R oute
1 . Pr es s t he  SE LEC T  ROUT E N UM BER fl exible  button ( FLASH 43, 
Bu tton #20) to  se le c t the  de si re d r o u t e n u mbe r.
2. Enter a valid ICLID route nu mber (000–252).
3. Press HOLD to change to the different  route  entered.  A confirmation 
tone  is  he ard.
Des crip ti on
Keys et s d esi gna te d t o r ing o n an i ncomi ng C O l ine  but  not  de si gnat e d t o 
ring o n the  ICLID  ring,  may  receive a  ring cy cle before the call  is  moved. 
The  sa me  ri ngi ng res tri cti ons  appl ie d to C O  li ne  ri ngi ng a re  ap pli e d to 
IC LID ring ing.  By d efa ult,  no de stina tions  or  ringing as signme nts  e xis t. 
						

							3-34 Direct  In ward Dialing  (DID)  Prog ra mming
Di re c t In wa rd  Di a l i ng ( DID)  Prog ra mmi ng
Pro g ram mi ng  S te ps
Pre ss FLASH an d di al  [4 4]. The following message displays:
[RRR]  = Route Number ( 00 0-49 9)
[# ## ] = D I D N u mb e r ( Di r e c t o r y  #  f r om  C e n t r al  O f fi c e )
[n...n] = Name As signe d to DID Number
The top left  button  (ROUTE)  in  the flexible button field is  lit  for 
pr ogra mmi ng t he R out e  numbe r.  The  LED s for  t he U P  Butt on ( FLASH 44, 
Bu tton  #18), the  DOWN Button ( FLASH 44, Butto n #19 ) is  also lit.
Changi ng to a Di fferent D ID Route Numb er
1. Press either  the UP  Button ( FLASH 44, Butto n #1 8),
-or -
Pr es s t h e  DO WN   B u tt o n  ( FLA SH 44 , Bu tton #19).
2. Enter a valid Route Number (000-499) to be associated  with the DID 
Number.
This Route Number is the same Route Number in the  ICLID Ringing 
As si g n m e n ts  Ta ble  (FLASH 43) and determines the destination of the 
DI D num ber  a ssoci at ed  wit h t hi s Rout e  Numb er.  The  di spl ay  shows 
the route number as it is entered.
3. Press HOLD button to save the entry. A confirmation  tone is  heard.
DID  RRR  XXXXXXX
n......n 
						

							Direct Inward Dialing (DID)  Programm ing 3 -35
Des crip ti on
DID ca lls a re treated  as  an incoming ca ll and  follow  th e s ame rules 
es ta blishe d f or CO line s. DID  information trans ferred from  the network  is 
capt ur ed  and t r ansl at ed  t o di re ct  a s peci fi c DI D  numbe r  to  a s peci fi c 
station,  ACD  or  Hunt group of  station s, o r V oice Mail  group . T he  DID call 
app ear s  at  t he d est i nat ion  st at ion  unde r a n a ssi gne d LO OP  or C O  but ton.
Whe n r ece ivi ng a D ID cal l, the  d est i nat ion st at ion hear s the  C O li ne 
ri ngi ng a nd t he  ass ign ed  CO  or  LO OP b utt on f las hes  at  t he  in co ming  CO  
line  flash  ra te . T he  des tination station then  pre ss es  th e f las hing CO or 
LOOP bu tton,  is  connected to the  incoming  DID  call,  and  CO lin e ringing  
stops  and  the LE D f or  the C O or L OOP button  lights  stead y.
If the o utside caller disconnects from a two-party conversation, the 
Ce ntr al  O ffi c e op ens  t he loop and re tu rns  t he l i ne to idl e st at e. The  
sys te m de t ect s t he  di sconne ct  sig nal , r el ea se  th e l i ne,  and  pr ovid es  a 
busy  tone  t o the  key set / SLT  (unl es s t he S LT i s a  VM port ), a nd di sconne cts  
from the  DID line. If the extension called hangs  up the phone, the central 
office detects dis connects,  and returns  the line to the idle s ta te.
The buttons  on the  digital telephone are defined  as  shown  when 
ent er i ng t he  DI D T abl e  pr ogra mmi ng ar e a:
By default, all entries  in  the DID  Table (000-999) have phone  numbers 
ass ign ed.  Refe r  t o Figure 3 -9  for additional information.
ROU TE
NUMBERPH ONE
NUMBERNAMECLEAR
ENTRY
=1Q=2W=3E=4R
BA C K
SPACE
=5T=6Y=7U=8I
=9O=10 P=11 A=12 S
=13 D=14 F=15 G=16 H
UPDOWN
=17 J=18 K=19 L=20 ;
=21 Z=22 X=23 C=24 V 
						

							3-36 Direct  In ward Dialing  (DID)  Prog ra mming
DI D  Ph on e  Nu mb er
Pro g ram mi ng  S te ps
1 . Pr es s t he  P HO NE  NUM BER f le xibl e  but ton  (FLASH 44, Button  #2) to 
pr ogra m t he  DI D Num ber.
2. Enter the  DID Number to be  associated with  a valid Route  Number 
(000–499).  Up to 7 digits can  be  entered.
By default, only the last three  digits  are used  for  routing which is 
determined in Flash  45.
3. Use the BACK SPACE flexible button ( FLASH 44, Butto n #5) to erase 
the current number or to correct for errors.
4. Press HOLD to save the entry. A confirmation  tone is  heard.
If  t he  DID  numb er  i s a lr ea dy i n t he  DI D Tr ans lat i on Tabl e,  th e R out e  
Number associated with the  DID number displays.
Na m e A s sign ed  t o D I D  Nu mb er
Pro g ram mi ng  S te ps
1. Press the NAME  flexible button ( FLASH 44, Butto n #3) t o  e nte r  the  
des ir ed  name  f or the  DID  tr unk.  Maxi mum l eng th  is  8-char acter s.
2. Press the HOLD  button  to u pdate  the database. A  confirmation tone 
is heard.
3. Use the BACK SPACE flexible button ( FLASH 44, Butto n #5) to erase 
the current  letter to correct for errors.
By default, the DID T able is  filled  with numbers. If error  tone is  received when 
the HOLD  button is  pres sed,  the DID  Table is  full and  an  entry needs to be 
deleted to make room for this new phone number. 
						

							Direct Inward Dialing (DID)  Programm ing 3 -37
DID  Na me a nd Numb er  Codes
The  di spl ay  shows  th e D ID  nam e or  num ber  a s i t  is  e nte re d.
Fi g u re  3- 1:  D I D N a me /N u mb er  C o d es
Erasing a DID Table  Entry
Pro g ram mi ng  S te ps
Cl ear i ng  E nt r ies  f r om DI D T a bl e
1 . Pr es s t he  CL EA R EN TRY But ton 
(FLASH  44, Button  #4) to   c le ar  an 
entire Phone  Number, Name and  Route from  the DID  Table.
2. Press the HOLD  button  to save the  entry.  A confirmation tone is 
he ard.
Ch an g i n g to a Di ff er en t  D ID Rou t e
Pre ss the  UP but ton 
(FLA SH 44 ,  Bu tton  #18) to  adv anc e to  the  D ID  
Route Num ber,
-or -
Pre ss  the  D OWN  but t on 
( FLASH 44, Butto n #19) to return to a  previous 
DI D Rout e  Numb er .
Other Codes
1  = 1# 8 = 8#“ = 01 *  = *#
2  = 2# 9 = 9# , = 02 ( = #1
3  = 3# 0 = 0# ? = 03 ) = #2
4  = 4# Space = 11 /  =  04 + = #3
5  = 5# : = 12 ! = * 1 = = #4
6  = 6# - = 13 $ = *2 # = ##
7 = 7#‘ = 14 & = *4 .  =  24 
						

							3-38 Direct  In ward Dialing  (DID)  Prog ra mming
Des crip ti on
By default, all entries  in  the DID  Table (000–999) hav e  phone  numbe rs 
ass ign ed.
The following  table shows  the default configuration  for  the DID Table 
entries and the  ICLID Ringing assignments.
Ro ute 000 in the ICLID Ringing Assignment Table is used as the intercept 
route . C alls  to  numbe rs  not contained  in  th e D ID  table  follow Route  000. 
If  Route 000  is  de faulte d to N one,  th e ca ll follow s Route  001.
Ro ute 001 is used  as the Busy DID Route. DO NOT program any  entries in 
this  Route if you intend to provide a  busy tone to callers  dialing a busy 
DI D/ DVI S numbe r.
Ta ble  3-9: DID & ICLID Defa ult Table Entrie s
DID Transl at i o n T abl e I C LI D  Tr an s la ti o n  Tabl e
DI D Ta bl e  
Entr yDefault 
Ro ute( s)IC L ID  Ta b le 
Ent ryDefault 
Destination
000-09 8
099
100-19 8
199
200-29 8
299
300-39 8
399
400-49 8
499
500-59 8
599
600-69 8
699
700-79 8
799
800-89 8
899
900-99 8
999100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
199
100-19 8
1991 00A-198A
499A
1 00A-198A
499A
1 00A-198A
499A
1 00A-198A
499A
1 00A-198A
499A
1 00A-198A
499A
1 00A-198A
499A
1 00A-198A
499A
1 00A-198A
499A
1 00A-198A
499A 
						

							4
St at io n At tributes
Programming
This c hapter desc ribes the steps  and proc edures necessary to
program station attributes.