Starplus Triad S System Programming Manual

							9-10 To l l  Res trictio n
Des crip ti on
Each Allow T able con ta ins  20 b in numbe rs . E ach b in numbe r may be up 
to  8  digits,  including Do Not Care digits and Search Special Table 
commands. Entries into the Allow Table represent exceptions to numbers 
or  cod es  tha t a re to be allowed only if they  would  otherwis e be res tricted  
by an entry in the Deny Table.
Ex a m pl e
If [1 555 1212] is allowed but [1+] numbers are denied,  by  an entry  into 
the Deny Table, [1 555 1212] is entered into the Allow Table as an allowed 
numbe r.
†Al l ow Tabl e A is  re fe re nc ed and sea rc he d f ir st  (be for e Deny  Tabl e A) 
when  St at ion  COS  i s 2  a nd CO  Li ne  CO S i s  ei the r  1  or  2.
†Al l ow Tabl e  B is  r efe re nc ed  and  look ed  at  fi rs t  (be fore  D eny Ta ble  B) 
when  St at ion  COS  i s 3  a nd CO  Li ne  CO S i s  ei the r  1  or  3.
†Whe n St at io n CO S i s  4  and C O L ine  CO S  is  1  bot h al l ow t abl es  ar e 
looked  at  first (Allow Table A first,  then Allow Table B) then  both deny 
ta bl es (De ny Tabl e A  fi rs t, the n D eny Ta bl e B ) .
Do  N ot  C are  d igi t s s peci fy tha t the  sy st em shoul d consi de r any d igi t  
di ale d i n t hat  p osi ti on a s a  mat ch. D o Not  C ar e d igi ts  sh ould  not  be  
entered as the last  digit in an  entry, as this would be an unnecessary 
or mea ning le ss command.
Search Special Table comma nds  must  be  e nte re d i n a  sp eci fic 
manner  and  should always be the last entries  in  the Allow Table. It is 
re c o mmen ded th at th e l as t fo u r bi ns (1 7–2 0)  i n t he  Al low  Ta bl e b e 
re se r ved  fo r  re fe re nc ing  th e f o ur  spe c ial  t ab le s wi t h t he  re fer enc e  t o  
the  hom e a re a code  (S pe cial  Tab le  4 ) al ways  be ing  loca te d i n b in 
number  20.  Search  Special table commands can only be entered into 
the  a ll o w t abl es .
Rem ember to enabl e 911 fo r all Classes of Service 
						

							To ll  R e s t r ic t i o n 9 - 1 1
Rule s f or  E nt ri es  t h at  R efe rence  Spe ci a l T a bl es
For  e ntr ie s  re fer e nc ing  the  fi r st  t hre e  spe c ia l t ab le s a  sp ec i fic   are a  c ode 
must  b e i de nti fi ed  (one  for  ea ch t abl e  nee de d). T he n mak e no te  as  t o 
how t he numb er s ar e d ial e d when d ial i ng numbe rs  to t hi s ar ea  c ode (e .g. , 
with a  l ead ing  di git [1] or n o le adi ng  digi t [1] ).
The entry into the  Allow Table would  be  entered as follows:
†Lea ding  Di gi t [ 1]:  Enter [ BB]  [1] [XX X] [D DD]  [S]  or,
†Non-Le adi ng  [1]:  En te r  [BB] [XXX ] [D DD]  [S]
BB = Bi n Numb er (Bi ns 17-19)
XX X = Area  C ode  (must match  AREA-X en try )
DD D = D o No t C are  digi t (t hre e en trie s,  D ND  b utton )
[S] = S ea rch S pe cial  Ta ble  Comma nd (T RA NS  but ton)
For  an  ent r y t hat  r efe r enc e s t he  Home  A re a C ode  ta bl e ( Spe c ia l T abl e  4)  
the entry  may  also be entered  to  expect or  not expect a  leading digit [1]. 
In  fact, in some cases  it may be desirable to enter both of the following 
ent r ie s:
†Lea ding  Di gi t [ 1]  --  Enter [BB]  [1]  [DD D] { S}
 and /or,
†Non-Le adi ng [1] --  Enter [BB] [DD D] {S }
BB = B in nu mber  (Bi n 20)
DD D = D o No t C are  digi t (t hre e en trie s,  MUTE butto n)
{S} = S ea rch S pe cial  Ta ble  Comma nd (T RA NS  but ton)
Deny Table
Pro g ram mi ng  S te ps
1 . Pr es s t he  DE NY TABL E A o r D ENY  TABLE  B fl exi bl e  but ton (F LA SH 7 0, 
Bu tton  #2 o r #4). T he f oll owin g me ssa ge  dis pl ays:
If both l ead ing  d igit  [1] and  non-l ead ing d igit [1] entries ar e made 
to r efer en ce the  same tabl e, it i s ne cessary  to plac e t he le adin g di git 
[1]  en try  ahe ad  of th e  non -le adin g d igit  [1] e ntry  in  th e  Al low  Ta ble .
DENY   TABLE   A
01 E 02E 
						

							9-12 To l l  Res trictio n
2. When the  first two bin  locations are displayed, enter  the 2-digit  bin 
nu mber ( 01–10) of  the bin to be programmed.
3. Enter the  deny code:
[0–9] ,  [6], [#] = Corr esponding deny dig its numb ers
MUTE = Do No t Care digi t
4. Press the HOLD button to save the entry. A confirmation tone is heard 
a nd t he  di spl ay n ow upda te s.
5. When all  entries for  one table are  complete,  press the flexible button 
for  the next table.
Er a si n g a Bin  Nu m be r
1. Enter a  valid  bin numb er.
2. Press the HOLD  button.
Des crip ti on
Each De ny T able conta ins  ten bin numbe rs . E ach b in numbe r may be up 
to  eight-digits including {Do Not Care}  digits.  Entries in the  Deny Table 
re pr es ent  numb er s or  c ode s t hat  ar e  to  be  deni ed  or  re st ri c te d.  Common  
entries would  be  [1] for restricting all  [1+]  type of calls. Exceptions to this 
re st ri c t io n  wo uld  be  en te re d i nt o  t he  Al lo w  Ta ble .
†De ny Tabl e  A  is  r efe re nc ed  and  se arc he d o nly  aft er  t he  Al l ow Tabl e  A 
is  che ck ed  when  St at ion  COS  i s 2  a nd CO  Li ne  CO S i s  ei the r  1  or  2.
†De ny Tabl e  B i s r ef er ence d and  se ar ched  only  aft er  t he  A ll ow Tabl e  B 
is  che ck ed  when  St at ion  COS  i s 3  a nd CO  Li ne  CO S i s  ei the r  1  or  3.
†Whe n St at io n CO S i s  4  and C O L ine  CO S  is  1,  bot h a ll ow t abl es  ar e 
looked  at  first (Allow Table A first,  then Allow Table B) then  both deny 
ta bl es (De ny Tabl e A  fi rs t, the n D eny Ta bl e B ) .
- D o Not  Ca re di git s  spe cif y t hat  th e s yst em  shoul d cons ide r  any d igi t 
di ale d i n t hat  p osi ti on a s a  mat ch. D o Not  C ar e d igi ts  sh ould  not  be  
entered as the last  digit in an  entry.
- S ea rch  Spe cia l Tab le  comma nds  cannot be  e nte re d into the D eny 
ta bl es. 
						

							To ll  R e s t r ic t i o n 9 - 1 3
Spe cial Table
Pro g ram mi ng  S te ps
To prog ram  a Spe cia l T abl e , i t is  fi rs t nece ssa ry to ass ign  an are a code to 
the table (except for the home area code).
1. Press the appropriate AREA  CODE TABLE (#1 to #3) flexible button 
(FLASH 70, Bu tton s #9 to #11). The following  message displays:
2. Enter a valid area code.
3. Press the HOLD button to save the entry. A confirmation tone is heard 
a nd t he  di spl ay u pdat es .
Entering  Office Codes in a Special Table
1. Press the SPECIAL TABLE (#1  to  #4) flexible  button (F L ASH 7 0, 
Bu tton s #5 to #8) t hat  c o r re sp o nds  to   the  ar ea  c o de  pr o gra mme d 
above. T he  following mess age displays:
XX X =  A r e a  C o d e
2. Enter the  office codes  that  are to be allowed  or  removed as follows:
XXX [1]  = Al l ow Code
XXX  [0]  =  Remove  C ode  from  th e l i st
(XXX = An offi ce cod e f rom 20 0  t o 9 99 )
3 . Pr es s H OLD  af te r  eve r y c ode  en te re d. A  c onfi r mat ion  tone  i s  hear d 
a nd t he dis pl ay upd ate s. Mu lt ip le  codes  may be ent er ed in a r ow. The  
display updates  showing the  first six  codes in ascending order.
SPECIAL   TABLE    1 AC
SPECIAL   TABLE   1 AC   XXX 
						

							9-14 To l l  Res trictio n
Des crip ti on
The Special Tables  provide  greater flexibility in designing a  toll plan for  a 
par t icul ar  si te .
†Each  Specia l  Ta ble a llows entry of  up to 800 of fice codes ( 200–999).
†Three of  these tables must  be  assigned an area code by  which they 
are referenced. The fourth  table is  reserved  for  the home area code 
and re qui re s no are a co de ent r y.
†The  Sp ec i al  Tabl es  ar e  re fer enc e d t hr ough e ntr i es  in  th e a ll ow t abl es . 
Four  area  codes,  including  the home a rea code, can  be referenced  to 
these special tables for further definition. When  a Special Table is 
referenced, entries must  be  made in the  Special  Table specifying 
what  off ice  codes  ar e  al lowe d.
†Code s can  be a dde d to  the  al low l i st  or r em oved f rom  the  li st . W hen a  
Spe cia l  Ta ble  i s  ch ecke d fo r a  mat ch t o a  3 -di git  code  a nd not  f ound, 
the  s yst em  conti nue s t o se ar ch t he  nex t A l low/ D eny Tab le  t o be  
c hec ke d. T he s yst em  does  not  re tur n t o t he A l low Tab le  whi c h rout ed  
the call to the  Special Table. By  default,  no codes are on  the allow list.
ALLOW
TAB LE ADENY
TABLE AALLOW
TAB LE BDENY
TABLE B
=1Q=2W=3E=4R
SPECIAL
TABLE 1SPECIAL
TAB LE 2SP ECIAL
TABLE 3SPECIAL
TABLE 4
=5T=6Y=7U=8I
AREA CODE
TABLE 1AREA CODE
TAB LE 2AR EA COD E
TABLE 3DI SP LA Y
TABLES
=9O=10 P=11 A=12 S
=13 D=14 F=15 G=16 H
=17 J=18 K=19 L=20 ;
=21 Z=22 X=23 C=24 V 
						

							To ll  R e s t r ic t i o n 9 - 1 5
Disp lay Toll  Tabl e Entri es
Pro g ram mi ng  S te ps
Press the DISPLAY TABLES flexible button (FLA SH 70 , Bu tton #12) while 
entering information into  a table.
Viewing  Entries in an Allow or Deny Table
Two  entries at  a time are displayed o n the  bottom  line  of the  display.
1. Pres s the  DISPLAY TABLE S b utton a gain, the  next highe r  bins  displays.
2 . Whe n th e l ast  e ntr i es  are  di spl aye d, pr es s t he D IS PLAY  TA BLES  but to n 
again to show the first two entries.
X = Allow or Deny Code
E = End o f Entry
Viewing  Entries in a Special Table
Si x 3-di gi t  codes  al lowe d  dis pla y i n a scend ing  ord er  star ting  with the  
lowe st  e ntr y.
Press  the DISPLAY  TABLES button again, the  next 6 entries display. This 
continues until  all codes  are displayed.
XXX= Area Code
YYY= Allowed Offi ce Code
Des crip ti on
To  view all entries  in  the toll tables using the display on  the Executive 
telephone, press, the DISPLAY TABLES flexible button ( FLASH 70, 
Bu tton #12) multiple  times to scroll through the entries.
ALLOW    TABLE   A
01    XXXXXXXE 02    XXXXXXXX
SPECIAL   TABLE    1 AC   XXX
YYY   YYY   YYY   YYY   YYY   YYY
It is  re comme nde d to v iew al l en trie s  i n the  Al low an d De ny T abl e 
be fo re  lea vin g p rogra mming . Entr ies c an  be  en tere d n ea r th e b ottom 
of the list for searching the special tables or entries made in error. 
Viewing the entire Allow Table ensures proper entry and operation. 
						

							9-16 To l l  Res trictio n 
						

							10
Least Cost Routing
(LCR)
This c hapter provides the functional steps  nec essary to use  the  LCR
features with the ST A RPLU S Triad-S System.  To  implement the most
economical routes for an outside call, you must first enter the
Programming Mode. 
						

							Introduction 10-3
Introduction
Lea st  Cos t Routi ng (LCR) was des ign ed to sel ect  t he  most  e conomi cal  
progra mmed  route for a n outgoing call.  When a  statio n user  dials  an 
outside number,  the LCR feature analyzes the number and then 
automatica lly choos es  an  outs ide lin e f rom  the group  tha t  has  been 
progra mmed  as  mos t economical.
The LCR feature puts  the responsibility of  choosing the  least expensive 
route for each area code and exchange code on  the system 
administra tor, no t o n the  sta tion u ser.  In  orde r to  make  a  routing 
decision,  the LCR feature is programmed  in  the system  database. The 
successful operation  of this feature is  completely dependent  on the 
accuracy of  th e p rogramm ing.
There are eight (8) different tables which are set up to monitor the dialing 
of di gi ts  of  a st at i on and  t o se le ct  the  be st  r oute  p rogr amme d f or  the  cal l.
1. 3- Di git Ar ea/O ffi ce  Code  Routing  Ta bl e
2. 6-Digit Office  Code Routing Table
3. Exception Table
4. Route List Table
5. Insert/Delete Table
6. Daily Start Time Table
7. Weekday (Weekly) Schedule
8 . To l l  I n f o r m a t i o n   Ta b l e