Siemens Saturn Epabx Oc1e Dyad Digital Telephone User Instructions

							- 
SATURN EPABX 
CMU Procedures A30808X5051-E120-3-B919 
Issue 5, May 1986 
CUSTOMER MEMORY UPDATE PROCEDURE: TRKASSN 
TITLE: Trunk Assignments Page 6 of 6 
Table 101.3 Niaht Answer TvDes- 
pay-- 
NONE 
ANA 
SNAP 
ZUNAl 
ZUNA2 
ZUNA3 
ZUNA4 DESCRIPTION 
I 
Not assigned to night answer 
Assigned Night Answer 
Special Night Answer Position 
Zoned Universal Night Answer - Zone 1 
Zoned Universal Night Answer - Zone 2 
Zoned Universal Night Answer - Zone 3 
Zoned Universal Night Answer - Zone 4 . . . 
MNEMONICS USED IN THIS CMU PROCEDURE: 
Mnemonic 
CAS 
DIT 
FX 
EN 
SP Definition 
Centralized Attendant Service 
Dedicated Incoming Trunk 
Foreign Exchange 
Main/Satellite Service 
Port Equipment Number 
Special Access Office Channel Unit  
						

							/ 
I - 
-- 
SATURN EPABX A30808-X5051-E120-3-6919 
CMU Procedures Issue 3. December 1985 
CUSTOMER MEMORY UPDATE PROCEDURE: TRKGRP 
TITLE: Trunk Group Assignments 
Access Level: 3, 4 
STEP NO. PROMPT/EXPLANATION 
1. ) DIS TRKGRP pEq 
Page 1 of 10 
1 2. 1 DISPLAY TRUNK GROUP(S) (O-31) = nn nn 
Reouests trunk group(s) for which data is to be displayed. If ranqe nn =’ trunk group number(s) (O-31). 
is desired, enter-two trunk group numbers separated-by a space. 
Enter (CR> to display all. 
3. DISP ALL TRUNKS? (Y,N) = a 
Requests whether all trunks in the group are to be listed in the display. a = Y = Yes; a = N = No. 
Enterina (CR) is the same as enterina N for No. 
I. I > ADDTRKGRP I 
!. TRUNK GROUP NUMBER (O-31) = nn 
Requests trunk group number which is to be added. If trunk group nn = trunk group number (O-31). 
number is 0, 25-31 go to Step 4. If trunk group number is l-24, go 
to Step 3. 
3. BUSY LAMP THRESHOLD (o-100) = nnn 
Requests threshold setting for trunk group busy lamp on attendant nnn. = number of idle trunks (O-100). 
console, i.e., the number of idle trunks (O-100) remaining in the trunk 
group to cause the associated LED on the attendant console to flash. 
NOTES: 1. The threshold is set to zero if (CR>is entered. 
2. Busy lamps are provided for Trunk Groups l-24 only. 
4. TRUNK GROUP DISPLAY (1-8 CHARS) = aaaaaaaa 
Requests display character(s) to represent this trunk group on the aaaaaaaa = display characters; 
attendant console. see Table 102.1. 
Enter (CR) for none. 
I I 
5. TRUNK COS (O-31) = nn 
Requests trunk COS assigned to this trunk group. nn = trunk COS (O-31). 
NOTE: Trunks use the same Class-of-Service definitions as stations: those defined by the COSASSN proce- 
dure. However, most classmarks are ignored if the user is a trunk circuit. 
6. TOLL CODE REST LIST NUMS (O-19) = aaaaa 
Requests restriction list(s) that may be accessed by this trunk group. 
If more than one, separate by spaces. 
Enter (CR) for none. aaaaa = restriction list(s); 
see Table 102.2. 
7. TRUNK GROUP MISCELLANEOUS FLAGS = aaaaa . . . aaaaa 
Requests miscellaneous flag(s) to be set for this trunk group. If more aaaaa = flag(s); see Table 102.3. 
than one, separate each by spaces. 
Enter (CR) for none.  
						

							i - 
- 
SATURN EPABX 
CMU Procedures 
, 
A30808-X5051-E120-3-8919 
Issue 3. December 1985 
CUSTOMER MEMORY UPDATE PROCEDURE: TRKGRP 
TITLE: Trunk Group Assignments 
STEP NO. PROMPT/EXPLANATION Page 2 of 10 
. ASSIGN OUTGOING PARAMETERS? (Y,N) = a 
Requests whether parameters are required for outgoing (or outgoing a = Y = Yes; a = N = No. 
portion of two-way) trunks. If Y (Yes), go to step 9; If N (No), go to 
step 13. 
. ALTERNATE TRUNK GROUPS (O-31) = nn . . . nn 
I 
Requests alternate trunk groups (3 max.) to be assigned to the new nn = alternate group(s) (O-37). 
trunk group. If more than one, separate each by spaces. 
Enter (CR) for none. 
0. k;NG CALL USAGE = aaaaa 
Requests outgoing call usage type that applies to this trunk group. aaaaa = usage type; see Table 102.4. 
If TWX, go to step 12 (OC II only): if MSL or RLTBRANCH, go to 
step 13; for all others, go to step 11. 
. . _ 
1. OUTGOING CONTROL SIGNALING = aaaaaa 
Requests type of outgoing control signaling for this trunk group. aaaaaa = outgoing control; see Table 102.5. 
2. OUTGOING ADDR SIG (AUTO,DP,DTMF) = aaaa 
Requests type of outgoing address signaling that applies to this aaaa = signaling type; see Table 102.6. 
trunk group. 
13. ASSIGN INCOMING PARAMETERS? (Y,N) = a 
Requests whether parameters are required for incoming (or incom- a = Y = Yes; a = N = No. 
ing portion of two-way) trunks. 
If Y (Yes), go to step 14; If N (No), go to step 24. 
14. ) TRUNK GROUP PRIORITY LEVEL (O-31) = nn 
I 
Requests priority level to be set for attendant console answering nn = priority (O-31). 
of this trunk group (priority 31 is the highest). 
Enter (CR) for 0. 
NOTE: The trunk group priority levels O-3 are the only ones which apply to trunks directed to console 
groups 1-12 in Shared Tenant Service. 
15. INCOMING CALL USAGE = aaaaa 
Requests incoming call usage type that applies to this trunk group. aaaaa = usage type; see Table 102.4. 
If ACD, go to step 16; If DID, go to step 17; If CO or TIE, go to step 
22; If MSL or RLTMAIN, procedure is completed; for all other usage 
types, go to step 23. 
16. ACD HUNT GROUP NUMBER (O-63) = nn 
Requests ACD group number assigned to this trunk group; go to nn = ACD group (O-63). 
step 24. 
17. 
DID DIGITS EXPECTED (O-5) = n 
Requests number of DID digits expected from the CO. n = DID digits (O-5). 
I I 
18. 1 DID DIGIT DELETE COUNT (O-3) = n 
I 
Requests number of incoming DID digits that are to be deleted. n = delete digit count (O-3).  
						

							i- 
SATURN EPABX A30808-X5051-E120-3-8919 
CMU Procedures Issue 3, December 1985 
CUSTOMER MEMORY UPDATE PROCEDURE: TRKGRP 
TITLE: Trunk Group Assignments Page 3 of 10 
I STEP NO. PROMPT/EXPLANATION 
I 
19. DID CONVERSION TABLE INDEX (O-3) = n 
Requests conversion table number for conversion of incoming DID n = conversion table number (O-3) 
digits. 
20. DID NIGHT ANSWER TYPE = aaaaa 
Requests night answer type. If ANA, go to step’21; for others, go aaaaa = night answer type; 
to step 22. see Table 102.5. 
21. ANA EXTENSION NUMBER .= nnnn 
Requests extension number to which incoming ANA calls are to nnnn = ext number (O-9999) 
be routed. 
22. INCOMING CONTROL SIGNALING = aaaaaa 
Requests type of incoming signaling control for this trunk group.. aaaaaa = incoming control; 
see Table 102.5. 
23. INCOMING ADDR SIG (AUTO,DP,DTMF) = aaaa 
I 
Requests type of incoming address signaling that applies to this aaaa = signaling type; see Table 102.6. 
trunk group. 
24. ASSIGN DATA PARAMETERS?(Y,N) = a 
Requests whether data parameters are to be assigned to this trunk a =’ Y = Yes; a = N = No. 
group. If Y (Yes), go to step 25; if N (No), procedure is completed. 
Entering (CR) is the same as entering N for No. 
25. TRUNK DATA COS (O-31) = nn 
Requests trunk data COS to be assigned to this trunk group. Proce- nn = trunk data COS (O-31). 
dure is completed. 
1. ) DEL TRKGRP 
2. TRUNK GROUP NUMBER (O-31) = nn 
Requests trunk group number which is to be deleted. nn = trunk group number (O-31). 
NOTE: All trunks must be taken out of service and deleted before the trunk group can be deleted. 
I 1 
1. )CHATRKGRP 
NOTE: For most prompts, entering a (CR> indicates no change. 
2. TRUNK GROUP NUMBER (O-31) = nn 
Requests trunk group number which is to be changed. If trunk group nn F trunk group number (O-31). 
0, or 25-31 is entered, go to Step 4. If trunk group number l-24 is 
entered. (10 to SteD 3.  
						

							, 
I - 
- 
SATURN EPABX 
CMU Procedures A30808-X5051-E120-3-8919 
issue 3. December 1985 
CUSTOMER MEMORY UPDATE PROCEDURE: TRKGRP 
TITLE: Trunk Group Assignments Page 4 of 10 
STEP NO. PROMPT/EXPLANATION 
I 
BUSY LAMP THRESHOLD (o-100) = nnn 
Requests threshold setting for trunk group busy lamp on attendant nnn = number of busy trunks (O-100). 
console, i.e., the number of busy trunks (O-100) in the trunk group 
to flash the associated lamp on attendant console. 
Enter (CR> for no change. 
NOTE: Busy lamps are provided for Trunk Groups 1 - 24 only. 
i. TRUNK GROUP DISPLAY (1-8 CHARS) = aaaaaaaa 
I 
Requests display character(s) to represent this trunk group on the aaaaaaaa = display characters; 
attendant console. see Table 102.1. 
Enter (CR) for no change. 
5. TRUNK COS (O-31) = nn 
Requests trunk COS to be assigned to this trunk group. nn =J trunk COS (O-31). 
Enter (CR) for no change. 
5. CHANGE TCR LIST NUMS? r(N) = a 
Requests whether the Toll Code Restriction Lists are to be changed. a = Y = Yes; a = N = No. 
If Y (Yes), go to step 7; if N (No), go to step 8. Entering (CR) is 
the same as entering N for No. 
7. x)LL CODE REST LIST NUMS (O-19) = aaaaa 
I 
Requests restriction list(s) that may be accessed by this trunk group. aaaaa = restriction lists; see Table 102.2. 
If more than one, separate by spaces. (CR> = none. 
ENABLE TRK GRP MISC FLAGS = aaaaaaaae ,.. aaaaaaaaa 1 
Requests miscellaneous flag(s) to be set for this trunk group. If more aaaaaaaaa = flag(s); see Table 102.3. 
than one, separate each by spaces. Enter (CR) for no change. 
NOTE: Limit multiple flags to a single line of input. If additional flags must be entered, repeat the procedure. 
3. DISABLE TRK GRP MISC FLAGS = aaaaaaaaa . . . aaaaaaaaa 
Requests miscellaneous flag(s) to be reset for this trunk group. If aaaaaaaaa = flag(s); see Table 102.3. 
more than one, separate each by spaces. Enter (CR> if none. 
NOTE: Limit multiple flags to a single line of input. If additional flags must be entered, repeat the procedure. 
10. INTERFACE TYPE = aaaa 
Requests type of interface that applies to this trunk group. aaaa = interface; see Table 102.7. 
Enter (CR> for no change. 
11. CHANGE ALTERNATE TRK GRPS? (Y,N) = a 
Requests whether alternate trunk group assignments are to be a = Y = Yes; a = N = No. 
changed. If Y (Yes), go to step 13; if N (No), go to step 14. Entering 
(CR) is the same as entering N for No. 
12. ALTERNATE TRUNK GROUPS = nn . . . nn 
1 
Requests alternate trunk groups to be assigned to the new trunk 
nn = alternate group(s) (O-31). 
group. If more than one, separate each by spaces. 
Enter (CR) for no change.  
						

							I - 
SATURN EPABX A30808-X5051-E120-3-8919 
CMU Procedures Issue 3. December 1985 
CUSTOMER MEMORY UPDATE PROCEDURE: TRKGRP 
TITLE: Trunk Group Assignments 
STEP NO. PROMPT/EXPLANATION Page 5 of 10 
3. OUTGOING CONTROL SIGNALING = aaaaaa 
Requests type of outgoing signaling control for this trunk group. aaaaaa = outgoing control; 
Enter (CR) for no change. see Table 102.5. 
4. OUTGOING ADDR SIG (AlJTO,DP,DTMF) = aaaa 
Requests type of outgoing address signaling that applies to this 
aaaa = Signaling type; see Table 102.6. 
trunk group. 
Enter (CR) for no change. 
15. DELAY CONNECT TIMER (O-50) = nn 
Requests timer setting for delay prior to establishing connection. nn = delay x 0.1 second (o-50). 
Enter (CR> for no change. 
16. AWAIT DIAL TONE TIMER (o-100) = nnn 
Requests timer setting for delay prior to sending digits. nnn = await DT delay x 0.1 second (o-100). 
Enter (CR) for no change. 
17. TRUNK RESEIZE TIMER (o-100) = nnn 
Requests timer setting for reseizure time after releasing trunk. nnn = reseizure time x 0.1 second (o-100). 
Enter (CR) for no change. 
18. OUTDIAL FIRST DIGIT TIMER (o-200) = nnn 
Requests timer setting for delay after outpulsing first digit. nnri = delay x 0.1 second (o-200). 
Enter (CR) for no change. 
19. OUTDIAL INTER DIGIT TIMER (o-200) = nnn 
Requests timer setting for delay between digits during outpulsing. nnn = delay x 0.1 second (o-200). 
Enter (CR) for no change. 
20. CO RELEASE GUARD TIMER (o-200) = nnn 
Requests CO release guard timer setting. nnn = release interval x 0.1 second 
Enter (CR) for no change. 
0 (o-2oo). 
NOTE: This timer is used to delay outgoing seizures after the CO initiates a call disconnect. 
21. PBX RELEASE GUARD TIMER (o-200) = nnn 
Requests PBX release guard timer setting. nnn = release interval x 0.1 second (O-200). 
Enter (CR) for no change. 
NOTE: This timer is used to delay outgoing seizures after the PABX initiates a call disconnect. 
22. TRUNK GROUP PRIORITY LEVEL (O-31) = nn 
Requests priority level to be set for attendant console answering nn = priority (O-31). 
of this trunk group. 
Enter (CR) for no change. 
NOTE: The trunk group priority levels O-3 are the only ones which apply to trunks directed to console 
groups l-12 in Shared Tenant Service. 
23. CHANGE ACD HUNT GRP NUM? (Y,N) = a 
Requests whether ACD hunt group number is to be changed. If Y a=Y = Yes; a = N = No. 
(Yes), go to step 25; if N (No), go to step 27. 
NOTE: Entering (CR) is the same as entering N for No.  
						

							I - 
-- 
SATURN EPABX A30808-X5051-E120-3-9919 
CMU Procedures issue 3. December 1985 
CUSTOMER MEMORY UPDATE PROCEDURE: TRKGRP 
TITLE: Trunk Group Assignments 
STEP NO. PROMPT/EXPLANATION Page 6 of 10 
14. ACD HUNT GROUP NUMBER = nn 
Requests ACD group number assigned to this trunk group. nn = ACD group (O-63). 
Enter (CR) for no change. 
!5. CHANGE DID PARAMETERS? (Y/N = n 
Requests whether DID parameters are to be changed. If Y (yes) n = DID digits (O-5). 
go to Step 27; if N (no) go to step 33. 
NOTE: Entering (CR) is the same as entering N for No. 
!6. DID DIGITS EXPECTED (O-5) = n 
Requests number of DID digits expected from the CO. n = DID digits (O-5). 
Enter (CR) for no change. 
!7. DID DIGIT DELETE COUNT (O-3) = n . 
I 
Requests number of incoming DID digits that are to be deleted. n = delete digit count (O-3). 
Enter (CR) for no change. 
!8. CHANGE DID CONV TABLE INDEX? (Y/N) = a 
Requests whether DID conversion table is to be changed. If Y (Yes) a = Y = Yes; a = N = No. 
go to Step 30; if N (No) go to Step 31. 
NOTE: Entering (CR) is the same as entering N for No. 
!9. DID CONV TABLE INDEX = n 
Requests conversion index number for conversion of incoming DID n = conversion index number (O-3). 
digits. 
30. DID NIGHT ANSWER TYPE = aaaaa 
Requests night answer type. If ANA, go to step 32. For others, go aaaaa = night answer type; 
to step 33. see Table 102.8. 
31. ANA EXTENSION NUMBER = nnnn 
Requests extension number to which incoming ANA calls are to nnnn = ext number (O-9999). 
be routed. 
32. INCOMING CONTROL SIGNALING = aaaaaa 
Requests type of incoming signaling control for this trunk group. aaaaaa = incoming control; 
Enter (CR> for no change. see Table 102.5. 
NOTE: Incoming Control Signaling only applies to trunks that receive digits. 
33. INCOMING ADDR SIG (AlJTO,DPDTMF) = aaaa 
Requests type of incoming address signaling that applies to this aaaa = signaling type; see Table 102.6. 
trunk group. 
Enter (CR> for no change. 
34. CHANGE DATA PARAMETERS (Y,N) = a 
Requests whether data parameters are to be changed. If Y (Yes) a = Y = Yes; a = N = No. 
go to Step 36; if N (No), procedure is completed.  
						

							SATURN EPABX A30808-X5051-E120-3-8919 
CMU Procedures Issue 3. December 1985 
CUSTOMER MEMORY UPDATE PROCEDURE: TRKGRP 
TITLE: Trunk Group Assignments 
STEP NO. PROMPT/EXPLANATION Page 7 of 10 
35. TRUNK DATA COS (O-31) = nn 
Requests the trunk data COS to be assigned to this trunk group. nn = trunk data COS (O-31). 
Entering (CR> is the same as removing the data COS. 
Table 102.1 Suggested Attendant Display Characters 
ALPHAMERIC 
INPUT DESCRIPTION 
FX-aaaa Foreign Exchange Trunk - aaaa denotes city or code. 
INWATS Inward WATS trunk. 
LOCAL-nn Local Trunk - nn denotes trunk group number. 
TIE-aaaa Tie Trunk - aaaa denotes other end of tie trunk. 
WATS1 Wide Area Telephone Service - Band 1. 
WATS2 Wide Area Telephone Service - Band 2; - 
aaaaWATS WATS Trunk - aaaa denotes state or national (e.g., FLWATS, NATLWATS, etc.). 
NOTES: 1. The alphameric characters shown above are suggestions only. 
2. lmbedded blanks are not permitted; use a hyphen (-) to separate fields (as shown above). 
Table 102.2 Restriction Lists 
ALPHAMERIC 
INPUT DESCRlPTiON 
0 
1 
: 
4 
5 
6 
i 
9 
10 
11 
12 
13 
14 
15 
16 
17 
18 
19 Eight-Digit Restriction List 0 
Eight-Digit Restriction List 1 
Eight-Digit Restriction List 2 
Eight-Digit Restriction List 3 
Eight-Digit Restriction List 4 
Eight-Digit Restriction List 5 
Eight-Digit Restriction List 6 
Eight-Digit Restriction List 7 
Eight-Digit Restriction List 8 
Eight-Digit Restriction List 9 
Eight-Digit Restriction List 10 
Eight-Digit Restriction List 11 
Eight-Digit Restriction List 12 
Eight-Digit Restriction List 13 
Eight-Digit Restriction List 14 
Eight-Digit Restriction List 15 
Fifteen-Digit Restriction List 0 
Fifteen-Digit Restriction List 1 
Fifteen-Digit Restriction List 2 
Fifteen-Digit Restriction List 3  
						

							RN EPABX 
I Procedures ‘, ‘A30808-X5051-E120-2-6919 
issue 2, November 1985 
CUSTOMER MEMORY UPDATE PROCEDURE: TRKGRP 
TITLE: Trunk Group Assignments 
Page 8 of 10 
ALPHAMERIC INPUT 
NONE 
TRKTOTRKO 
ASRO 
CBQ 
DMDR 
DAYCTRL 
DIDPREFIX 
DSRI 
DSRO 
EM4WIRE 
RCLTOANA 
NOANSRCLI 
NOANSRCLO 
REROUTE 
SMDRI 
SMDRO 
SPCLACCT 
SBYQ 
XFERSECURE Table 102.3 Trunk Group Miscellaneous Flags 
DESCRlpTlON 
No flags affected (applies only to CHANGE). 
Allow Trunk-toTrunk Connection Even if Both Trunks are Seized Outgoing. 
Answer Supervision Received - Outgoing. 
Trunk group provides outgoing queuing (Callback and,Stan,dby) for user accessing 
this group. (Not allowed on 2-way AUTO groups) 
Data Call Message Detail Recording Required (OC II only). 
Daytime Trunk Control Enabled. 
Digits from DID Conversion Table are to be Prefixed (See DIDCONV Procedure). 
Disconnect Supervision Received - Incoming. 
Disconnect Supervision Received - Outgoing. 
E&M Group Consists of 4.Wire Facilities, rather Than 2.Wire. 
Go to ANA Station on No Answer Recall, Even if System in Day Mode. 
No Answer Recall - Incoming. 
No Answer Recall - Outgoing. 
Reroute to Another Trunk on Failure to Detect DT. . 
SMDR - Incoming Calls Recorded. ,, -- 
SMDR - Outgoing Calls Recorded. 
Special Account Code (Does not apply to LCR). 
Standby Queuing. Incoming calls on this trunk group may standby queue for 
another trunk group (tandem trunking). 
Transfer Security Feature active on this Trunk Group. 
DIGITAL RESERVED FOR FUTURE USE 
TMBCDR NOT APPLICABLE TO DOMESTIC SYSTEMS 
Table 102.4 Incoming/Outgoing Call Usage 
ALPHAMERIC INPUT DESCRIPTION 
OUTGOING TRUNKS: 
co DIT 
DID 
DISA 
DISAS 
DPIGRP 
DPITRK 
FX 
TIE 
UCD 
WATS Central Office. 
DPI Direct Trunk Appearance. 
DPI Trunk Group Originate Button. 
Foreign Exchange. 
Teletypewriter Exchange Service. 
, Tie Trunk. 
Wide Area Telephone Service. 
INCOMING TRUNKS: 
Central Office. 
Dedicated Incoming Trunk. 
Direct Inward Dialing. 
Direct Inward System Access. 
DISA - Shared. 
DPI Trunk Group Answer Button. 
DPI Direct Trunk Appearance. 
Foreign Exchange. 
Tie Trunk. 
Uniform Call Distribution. 
Wide Area Teleohone Service.  
						

							.._ . . . 
I - 
- I 
SATURN EPABX 
CMU Procedures . A30808-X5051-E120-2-8919 
issue 2. November 1985 
CUSTOMER MEMORY UPDATE PROCEDURE: TRKGRP 
TITLE: Trunk Grow Assianments 
Page 9 of 10 
INPUT 
NONE 
DELAY 
DIALTN 
IMMED 
WINK 
lYY,ca I”&,” ‘..““~~.‘..J,~“.J”...~ W”....“. “.J..” . . . . J 
DESCRIPTION 
None Assigned. 
Delay Dial Signal 
a. Incoming - The SATURN EPABX returns a delay signal within 150 ms after trunk 
seizure. The signal persists for no less than 140 ms and ends when the EPABX is 
ready to receive address signaling. Dial tone is not returned. 
b. Outgoing - The calling party’s dialed digits are stored and forwarded to the trunk 
following the end of the delay dial signal from the distant end. 
Dial Tone (cut-through operation) 
a. Incoming - Dial tone is connected to the trunk when the SATURN EPABX is 
ready to receive address signaling. 
b. Outgoing - The calling party’s transmission path is cut-through to the trunk when 
the trunk is seized. Dial tone is returned from the far end when it is prepared to 
receive digits. 
Immediate Start (Senderized Operation) 
a. Incoming - The SATURN EPABX is ready to receive address signaling 65 ms af- 
ter the trunk seizure. Return of dial tone is optional. 
b. Outgoing - The calling party’s dialed digits are stored and forwarded to the trunk 
following the time-out of the first digit delay timer. 
Wink Start Signaling (Senderized Operation) 
a. Incoming - The SATURN EPABX returns a wink start signal when it is ready to 
receive address signaling; however, the wink start signal does not occur earlier 
than 100 ms after trunk seizure. Dial tone is not returned. 
b. Outgoing - The calling party’s dialed digits are stored and forwarded to the trunk 
following the receipt of the wink start signal from the distant end. 
Table 102.6 Incoming/Outgoing Address Signaling 
ALPHAMERIC INPUT 
AUTO 
DP 
DTMF DESCRIPTION 
Automatic. System provides/expects seizure/ringdown, but no outpulsing. 
Dial Pulse. System provides/expects dial pulse (loop) outpulsing. 
DualTone Multifrequency. System provides/expects DTMF outpulsing. 
Table 102.7 Trunk Group Interface Types 
ALPHAMERIC INPUT 
PCOH 
PCOL 
PAT0 
PATT DESCRIPTION 
Central Office Trunk - High Grade (See Note). 
Central Office Trunk - Normal. 
Pad - Analog Toll Office. 
Pad - Analog Tie Trunk. 
NOTE: On high-grade CO trunks, the system provides increased gain on CO to E&M connections. 
Table 102.8 Night Answer Types 
ALPHAMERIC INPUT DESCRIPTION 
NONE None Assigned. 
ANA Assigned Night Answering. 
SNAP Special Night Answering Position. 
ZUNAl Zoned Universal Night Answering - Zone 1. 
ZUNA2 Zoned Universal Night Answering - Zone 2. 
ZUNAB Zoned Universal Night Answering - Zone 3. 
ZUNM Zoned Universal Night Answering - Zone 4.