NEC Neax 2400 Ipx Feature Programming Manual

							NEAX2400 IPX Feature Programming ManualPage 68NDA-24297, Issue 1
A-121 Add On Conference - 8 Party
A-121  Add On Conference - 8 Party
General Description
This service allows the 8-party conference to be established any time by any conferee by use of the 8-party
conference trunk.
Operating Procedure
To establish an 8-party conference
1. Station A calls Station B; Station B answers.
2. Station A (or B) switch hook flashes (or press TRANSFER key) and dials Station C’s number; Station C
answers.
3. Station A (or B) who had dialed Station C’s number presses CONF key; the three-party conference is
established.
4. Station A (B, or C) switch hook flashes (or press TRANSFER key) and dials Station D’snumber;Station
Danswers.
5. Station A (B, or C) who had dialed Station D’s number presses CONF key; the four-party conference is
established. In the same way, any user connected to the 8-party conference trunk can establish the 8-party
conference by switch hook flash and pressing of the CONF key.
6. When one of the conferees (the user or the outside party) releases, another member can be added to the
conference by the same operation.
7. Single phone can add other conferee by switch hook flashes and dials telephone number, then switch hook
flashes again.
8. When one D
termstation and multiple outside parties (trunks) are connected to the 8-party conference trunk,
when the Dtermuser presses RETAIN CONF key and goes on-hook, the conference by the outside parties
(trunks) can be continued. In the other cases as when the station is not a Dterm, RETAIN CONF key is not
assigned, or there is only one outside party connected, the conference trunk is released automatically.
When conference has multiple outside parties (trunks), only D
terms can keep multiple outside parties still
in conference, but it releases by pressing RETAIN CONF key.
Service Conditions
1. The 8-party conference trunk will be treated as a station, and will have an intra-office route number.
2. The 8-party conference circuit card can be assigned to any slot.
3. A minimum of 1 CFTB-L is needed for this feature. A maximum of 20 8-party conference trunk circuit
cards (SPA-CFTB-L) can be installed per system.
4. The 8-party trunk assigned in a different tenant from the general station/trunk, and the connection between
the 8-party trunk and the other station/trunk is to be restricted (inter tenant restriction).
5. This service can coexist in the same system with the Three-Way Calling service using the three-way
conference trunk built in the line group = 21–23 of the odd numbered unit, and the current 8-party
conference service. If a station is assigned SFI 131, that station will use the 8-party conference trunk even
for a 3-party conference.
6. Any one of the station, central office line, tie line, CCIS line, or the ISDN network subscriber can be the
conference member.
7. The Attendant Console cannot be a member of the conference. Pressing the CONF key will be invalid.
8. The stations connected to the 8-party conference trunk can call the conferees separately any time. 
						

							NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 69
Add On Conference - 8 Party A-121
Service Conditions (cont’d)
9. When all of the eight ports of the 8-party conference trunk are filled with the conferees, no other conferee
can be added to the conference.
10. The station/trunk which is connected to the 8-party conference trunk can release from the conference at
any time.
11. An incoming call from the ringdown trunk, where release cannot be detected, cannot be connected to the
8-party conference trunk.
12. Assign non-effective hold trunk check in system data for release of ineffectively held trunks at routine
diagnosis to prevent the 8-party conference trunk being held up.
13. When all the trunks and stations connected to the 8-party conference trunk release, the conference trunk
becomes free. Until then, the same trunk cannot be used by another group for an 8-party conference.
14. On the LCD display of the D
termstations, the number of the stations and trunks attending the conference
is shown as STA:3, TRK:2 on the upper line. (Name Display service is not available.)
15. The 8-party conference trunk cannot be called from a station, outside party, or the Attendant Console
(reorder tone is sent out when attempted).
16. The following services are not available for the stations/trunks connected to the 8-party conference trunk:
ATTENDANT CAMP-ON WITH TONE INDICATION [A-1]
BROKERAGE HOT LINE [B-6]
BUSY VERIFICATION [B-3]
CALL WAITING - TERMINATING [C-12]
CALL WAITING - ORIGINATING [C-31]
NAME DISPLAY [N-28]
PRIVACY RELEASE [P-18]
17. In the following cases, 8-party conference service via CONF key is not available:
a.) when the service is not set in system data
b.) when the service is restricted
c.) when the 8-party conference trunk is not assigned, not accommodated, or busy.
In the cases above, if Three-Way Calling service is available and the three-way conference trunk is
provided, this service is provided by pressing the CONF key. The LCD of the D
termconnected to the
conference trunk shows CONF when using Three-Way Calling service.
18. When a station connected to the 8-party conference trunk transfers a call to another station and the
operating station goes on-hook whether transferred station answers or not, the 8-party conference trunk
recalls to the operating station.
19. The 8-party conference trunk cannot be assigned as the destination of CALL FORWARDING - ALL
CALLS [C-5] / - BUSY LINE [C-2] / - DON’T ANSWER [C-3] service.
20. ADD-ON CONFERENCE - 8 PARTY [A-121] cannot be activated by a single line phone.
21. When the conferee presses the RETAIN CONF key, the LCD display shows as follows for five seconds
depending on the connection:
a.) one station and multiple outside parties RETAIN CONF
b.) one station and one outside party REST
c.) multiple stations REST
Only in the case“a”above, the conference status is retained.
22. When a D
termuser who has Retain Conference presses the RETAIN CONF key a second time, Retain
Conference is cancelled. At that time, the LCD of the Dtermindicates DISCONNECT CONF and the 8-
party conference trunk is released after the stations go on-hook.
23. When only two parties (station/station, station/outside party, outside party/outside party) are connected to
the 8-party conference trunk, when either one of the parties releases, the conference trunk is released. 
						

							NEAX2400 IPX Feature Programming ManualPage 70NDA-24297, Issue 1
A-121 Add On Conference - 8 Party
Service Conditions (cont’d)
24. The station setting Retain Conference can only cancel Retaining Conference or go on-hook. (No other
operation is available.) When the station goes on-hook, the RETAIN CONF lamp turns off.
25. In case of trunk call origination, the billing is performed against the station which originated the trunk call
until the trunk releases. Therefore, there may be several billing messages sent for the same time for the
same station.
26. During the 8-party conference, the CONF lamp remains lit.
27. When this service is activated in an FCCS network, hardware conditions for connection trunks are as
shown below:
Programming
STEP 1:ASYD- System data 1, index 92, bit 4 = 0/1. This enables tenant-to-tenant route restriction service.
System data 1, index 94, bit 0 = 0/1. This enables tenant-to-tenant restriction service.
System data 1, index 432, bits 0-3. Assign the first digit of the pilot number used for this service.
System data 1, index 432, bits 4-7. Assign the second digit of the pilot number.
System data 1, index 433, bits 0-3. Assign the third digit of the pilot number.
System data 1, index 433, bits 4-7. Assign the fourth digit of the pilot number.
System data 1, index 434, bits 0-3. Assign the fifth digit of the pilot number.
Note:1 through 5 digits may be used; assign the bits accordingly. If a digit is not used, assign those bitsas“0’.
Ifa bit is used for 0, see the following example:
System data 1, index 432 is A7,
System data 1, index 433 is 00,
System data 1, index 434 is x0.
STEP 2:ASFC- For the SFC used by the CFTB-L or SP-1114 on PA-CFTB, assign SFI 32 = 1.
For the SFC used by stations that will use this feature, assign SFI 131 = 1. If you do not want certain
people to use this feature, make sure that SFI 131 = 0 in the SFC that the phone is programmed to.
STEP 3:ASDT- assign stations to each level of the CFTB. Assign TEC = 27 for each level and ensure that the
CFTB levels are assigned in a separate tenant and separate SFC from non-CFTB levels.
STEP 4:ASHC- Assign a STATION HUNTING - CIRCULAR group for stations programmed to LEN levels
1 through level 7 of the PA-CFTB circuit card(s). For more details, see the figure on the following
page.PA-24DTR SP-3010 Issue No. 13 or later (SW13-8: OFF)
PA-30DTT SP-3012 Issue No. 8 or later 
						

							NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 71
Add On Conference - 8 Party A-121
Programming (cont’d)
STEP 5:ASHP- When the system accommodates multiple PA-CFTB circuit cards, assign a STATION
HUNTING - TERMINATING group for the stations programmed to LEN level 0 of each PA-CFTB
circuit card. For more details, see the figure below:
STEP 6:AKYD-assignFKY83toanyD
terms that require the use of the Retain Conference feature.
STEP 7:ADSL- Assign SN=3 (STATION BUSY) and FKY=13 (THREE-WAY CALLING;CONF).
Assign FKY=83 (RETAIN CONFERENCE; RETAIN) to any D
termwhich require the use of the
RETAIN CONFERENCE feature.
This command is required for assigning the function to each soft key.
STEP 8:ARSC- assign Restriction data between routes and the RSC used by the CFTB.
STEP 9:AT N R- assign restriction data between tenants.
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
Note
STEP 1:ASYDL- This data must be assigned to the node set Add On Conference - 8 Party.
System Data 1, Index 527, bit 4 = 1
Note:When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required
in addition to ASYDL or ASYDN.
STATION HUNTING - CIRCULAR groups assigned by 
ASHC command
STATION HUNTING - TERMINATING groups assigned by 
ASHP command
Pilot LV7
LV0PA-CFTB PA-CFTB PA-CFTB 
						

							NEAX2400 IPX Feature Programming ManualPage 72NDA-24297, Issue 1
A-125 Analog Caller ID (Class SM)
A-125  Analog Caller ID (Class SM)
General Description
This feature allows the Dtermto display calling party’s number and/or name on the LCD when a call from analog
C.O. line is terminated. In addition, the calling number can be output as a part of SMDR information.
Caller ID information can be displayed on an analog telephone with a display device or the display of a D
term.
Operating Procedure
No manual operation is required.
Service Conditions
1. This service is available when an incoming call from C.O. line is terminated directly to a station.
2. First ringing pattern for this service is 2-seconds ON and 4-seconds OFF. After that, ringing pattern
assigned by system data is applied.
3. The calling numbers received by using this feature or current MF/ISDN feature may be output to the
SMDR expanded area.
4. A calling number cannot be received during conversation.
5. The calling numbers which may be added to SMDR output are the dial code only. The calling name is not
added.
6. This service is not provided for the Attendant Console.
7. This service is not applied to SAVE AND REPEAT [S-24D] service. The calling number received may
not be saved.
8. A maximum of 256 calls per LP are available at the same time.
9. When an incoming call is sent as a test, the LCD does not display both the number and the name.
10. Display conditions are shown below. Also, the ID display of ISDN service has the same conditions.
a.) It is assigned by system data in which display of the calling number or name has priority on
termination. When the calling name has priority, the LCD displays:
When the calling number has priority, the LCD displays:
*1- In ISDN service, the sub-address is displayed. When the D
termdoes not receive the data
pertaining to the sub-address, nothing is displayed.
*2- If the prior display is not assigned by system data, the other is displayed.
b.) The calling number and name may be exchanged by pressing the feature key, according to the
following conditions:
When my line is prime line, displays may be exchanged during termination or conversation.
When my line is not the prime line, displays may be exchanged only during conversation.
c.) When the received numbers of a calling number and calling name exceed the display field, the
decision to put the digits to the right or left may be chosen in system data. An“*”is indicated on
the exceeded digit position.(Time Display)
Calling Number XXXXXXXX
Caling Name* 1
* 2
(Time Display)
Calling Name     XXXXXXXX
Caling Number* 1
* 2 
						

							NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 73
Analog Caller ID (Class SM) A-125
Service Conditions (cont’d)
d.) The display is flashing during termination. It is lit during conversation.
e.) The following are examples of displays when the received digits of a calling number and name
exceed the display field:
OR
OR
OR
Programming
See also TRUNK LINE APPEARANCE[T-23]for information on how to accommodate C.O. line on
aDtermline/feature key.
STEP 1:ASYD- System Data 1, Index 241, Bit 6. 0/1=When the length of Caller ID exceeds the limit, only the
former/latter part of data appears on the LCD.
System Data 1, Index 390, Bit 0. Caller ID display pattern on the LCD. 0/1=Calling Number/Calling
Name has priority.
System Data 1, Index 390, Bit 2. When using D
term2-line LCD, the lower LCD can be used for
displaying Caller ID. 0/1=Out/In Service.
When Calling Number is output to SMDR, the following expanded format is used:(Time Display)
                               1234567*
ABCDEFGHIJKLMNOPQRSTUVW*Calling Number
Calling Name
(Time Display)
                               *4567890
*DEFGHIJKLMNOPQRSTUVWXYZCalling Number
Calling Name
(Time Display)
                               ABCDEFG*
12345678901234567890123*Calling Name
Calling Number
(Time Display)
                               *TUVWXYZ
*89012345678901234567890Calling Name
Calling Number
 H = Origination
 I = Termination
 J = Station-to-Station
S
T
XOKH
/
I
/
J ! OFFICE CODE OF 
CALLED PARTY 
(FOR CCIS)AUTH 
CODE
Identifier:
0 = Output is not available
1 = Displayed
2 = Display denied
3 = Service is not available
4 = Origination from public pay phone
Note:
For 0, 2 and 3, the ANI number is not output.
AANI 
NO.ZE
T
X
A = ANI Information
Z = End of SMDR 
Information 1 96 104 129 130 131 1622 
						

							NEAX2400 IPX Feature Programming ManualPage 74NDA-24297, Issue 1
A-125 Analog Caller ID (Class SM)
Programming (cont’d)
System Data 1, Index 288, Bit 5. Expanded SMDR Output for SMDR A Apparatus. 0/1=Out/In
Service.
System Data 1, Index 290, Bit 5. Expanded SMDR Output for SMDR B Apparatus. 0/1=Out/In
Service.
System Data 1, Index 292, Bit 5. Expanded SMDR Output for SMDR C Apparatus. 0/1=Out/In
Service.
System Data 1, Index 294, Bit 5. Expanded SMDR Output for SMDR D Apparatus. 0/1=Out/In
Service.
System Data 1, Index 296, Bit 0. Output of Calling Number (ANI information). 0/1=Out/In Service.
Assign data“1”.
System Data 1, Index 300, Bit 0. 0/1=-/Billing information is sent to the Main Node in Expanded
SMDR format in the case of CENTRALIZED BILLING - CCIS [C-55].
STEP 2:ASFC- Assign a Service Feature Class that allows SFI 14 to stations allowed STATION MESSAGE
DETAIL RECORDING [S-10].
Assign a Service Feature Class that allows SFI 146 to analog stations allowed this service.
STEP 3:ARTD- Assign route class data for the C.O. trunk.
15-LSG :3 50-DPLY :1
When Calling Number is output to SMDR:
10-SMDR :1
STEP 4:AT R K- Assign trunk data for the C.O. trunk.
STEP 5:MBTK- Cancel the make busy of the C.O. trunk.
STEP 6:AKYD- Assign Call ID Change Display key. Assign Type:Function: [113].
STEP 7:ADSL- Assign ID CHG key; SN=4 (Communication in Progress), FKY=113 (Call ID Change
Display).
This command is used for assigning a function to each soft key on the D
term.
FCCS Programming 
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
Note
STEP 1:ARTDN- Assign route class data for the C.O. trunk.
15-LSG :3 50-DPLY :1
When Calling Number is output to SMDR:
10-SMDR :1
Note:When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required
in addition to ASYDL or ASYDN. 
						

							NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 75
Analog Caller ID - Station A-127
A-127  Analog Caller ID - Station
General Description
This feature allows a called station to receive CALLER ID information (time, calling number and name) from
Central Office when a call terminates via the analog COT. The calling number received from the ISDN network,
MF-ANI information received from Central Office with the MF feature or the calling telephone number within the
PBX can change into CALLER ID information and be sent to the called station.
This feature is also provided for the analog station equipped with the function of receiving the calling number. This
function is called Analog Caller ID - Station by Modem Sender.
Operating Procedure
No manual operation is required.
Service Conditions
1. This service is provided for analog stations.
2. Message types of CALLER ID information sent to a called station are as follows:
04H: Calling Number Delivery Information (for Calling number)
80H: Call Setup (for Calling number and name, or reason not to inform.)
3. When a call terminates via another station, the number of intermediate station will be sent. After that
station hangs up, the number of the originating party will not be sent: CALLER ID of the first termination
is only sent.
4. If a calling number exceeds 10 digits, the first or last exceeded digits will be deleted according to system
data.
5. This service is not provided if a call does not terminate directly on a line: in the case of termination using
such services as Call Pickup, Executive Right-of-Way.
6. This service is not provided when a calling party is the Attendant Console.
7. This service is not provided for the 1 A2 key telephone.
8. This service is not available in boss-secretary service.
9. The first ringing upon termination is 2-second ring and 4-second silence. A ringer pattern is provided from
the second ringing.
10. The following firmware is required to be equipped on the circuit cards:
11. The following are service conditions for Analog Caller ID - Station by Modem Sender:
a.) This service is also provided for analog stations equipped with the function of receiving the
calling number.
CIRCUIT CARDFIRMWARE
PA-8COTBJSW-317 8COTBJ PROG-A
SP-1122 CALL-ID PROG-A
SP-3190 8COTBJ PROG-A
PA-8LCBRSW-331 8LCBR PROG-A
SP-3207 8LCBR PROG-A
SP-1123 CALL-LC PROG-A 
						

							NEAX2400 IPX Feature Programming ManualPage 76NDA-24297, Issue 1
A-127 Analog Caller ID - Station
Service Conditions (cont’d)
b.) Message types of Caller ID information sent to a called analog station are as follows:
Message type - 04H: Calling Number Delivery Information (for calling number)
Message type - 80H: Call Setup (for calling number, name, or reason not to inform)
Parameter - 02H: Calling line DN parameter
- 04H: Reason for absence of calling DN Parameter
- 07H: Name
- 08H: Reason for absence of name
c.) When the reason not to inform the caller ID is received through C.O. line, the reason is notified.
d.) The function equipped with the station for restricting the caller ID notification cannot be used.
e.) The caller ID notification can be restricted only when originating the trunk call. When restricting
the caller ID notification on each conversation, dial the number following the numbering plan
preassigned at the self-PBX.
f.) If a calling number exceeds 10 digits, the first or the last exceeded digits will be deleted
according to system data.
g.) When a call terminates via another station, the number of intermediate station will be sent. After
that station hangs up, the number of the originating party will not be set: CALLER ID of the first
termination is only sent.
h.) The caller ID notification is not provided for the following services because the call is not
terminated to line using the services.
CALL PICKUP GROUP [C-7, C-7D]
CALL WAITING-TERMINATING [C-12]
CALL WAITING-ORIGINATING [C-31]
EXECUTIVE RIGHT-OF-WAY [E-1]
Also, the caller ID notification is not provided to the boss station for Boss-Secretary service.
i.) The system starts to count for No Answer timer when the caller ID notification process is
complete.
j.) The incoming call using this service is also counted as the maximum number of calls terminated
at the same time in a system.
k.) Since some telephones cannot display the telephone number using“*”or“#”(other than the
numerical digits), telephone number of numerical digits is recommended to use.
l.) The maximum number of Register/Sender trunk in an LP is 64. And, when the maximum number
of Register/Sender trunks is assigned (64 ×LP no.), the ISDN/CCIS call cannot be originated or
terminated (the same as the usual system condition).
m.) The following messages are notified when the reason for restricting caller ID notification is
received.
P: Privacy Security
O: Outside Area where Service is not provided
n.) When the same station is set“1”at both SFI 168 (Analog caller ID station by modem sender,
released R7 or later) and SFI 146 (existing Analog caller ID) in ASFC, the existing Analog caller
ID has priority (Do not assign both data to the same station. The data assignment to different
stations in a system is available).
o.) Calling number conversion (add or delete preassigned numbers) is not available when the caller
ID information is received via Analog Caller ID trunk.
p.) The first ringing upon termination is 2-second ring and 4-second silence. A ringer pattern is
provided from the second ringing. 
						

							NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 77
Analog Caller ID - Station A-127
Service Conditions (cont’d)
q.) When the calling party or the intermediate party is Attendant Console, or the calling party number
is not received when the call is terminated via C.O. line or tie line, the calling number cannot be
notified.
r.) When the Name Display data is assigned to the calling party in station-to-station calling, the
calling party’s name is also sent to the called party. Note that only 1 byte character data can be
effective in this case. Since the name data is sent without confirming whether the proper character
is used or not, characters that are not proper may cause abnormal status to the system.
s.) When all the sender trunks are busy, the calling number cannot be notified.
12. To activate the Analog Caller ID - Station by Modem Sender service in the FCCS network, the sender
trunk for sending Modem signal (RT=937, ATRK) should be accommodated in the all nodes where the
stations providing the service is installed.
Interactions
1. The following circuit cards are required for this service:
PA-8RSTY
PA-16LCBY
Note
Note:
16LCBY and 8RSTY must be used together for Caller ID.
2. Only one route number can be assigned for each sender and register in a PA-8RSTY card.
3. This service is not provided for Hotel system.
4. This service is not provided for the call using OAI system.
Programming
STEP 1:ASFC- Assign the service feature class to each analog station.
DAY/NIGHT: D/N
TN: Tenant Number
SFI: 168=1 (Analog Caller ID Station by Modem Sender is available)
When Calling Number Delivery (Message Type - 04H) is notified
SFI: 153=1
STEP 2:AT R K- Assign the sender trunk data.
Note 1
RT: 937
Note 1:RT 937 must be programmed in level 4, 5, 6, or 7 for FSK Sender. Level 0, 1, 2, or 3 may be used for RT
902 or PB/MF Sender.
Note 2:Optional ASYD-SYS1, Index 246, b6. When a calling number exceeds 10 digits: 0/1= The last/first exceeded
digits are deleted.
FCCS Programming 
No unique programming is required for the FCCS network.