Home > NEC > Communications System > NEC Neax 2400 Ipx Feature Programming Manual

NEC Neax 2400 Ipx Feature Programming Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax 2400 Ipx Feature Programming Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 1089
    Add page 1081 to Favourites
    image text
    Enable zoom 
    							NEAX2400 IPX Feature Programming ManualPage 1038NDA-24297, Issue 1
T-26 Toll Restriction - 3/6-Digit - CCIS
Programming (cont’d)
DC: 91914 TDI: 1 (Allow)
This allows these specific Area Codes. All Area Codes not assigned are automatically restricted.
    Add page 1082 to Favourites
    image text
    Enable zoom 
    							NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 1039
Trunk Answer from Any Station - CCIS T-27
T-27  Trunk Answer from Any Station - CCIS
General Description
This feature allows any station not restricted from incoming calls to answer incoming calls when the network is in
Night mode.
When this feature is activated, incoming Central Office calls will activate a common TRUNK ANSWER FROM
ANY STATION (TAS) signal. By dialing a specified code, any station may answer the call and extend it to any
other station in the CCIS network using CALL TRANSFER - ALL CALLS - CCIS [C-50].
Operating Procedure
To answer an incoming call
1. The TAS signal sounds indicating an incoming call.
2. Lift the handset and receive dial tone.
3. Dial the TAS access code; the incoming call is connected.
Service Conditions
1. An incoming call terminating in the Night mode will be forwarded to the TAS equipment of the
terminating node.
2. An incoming call to the main node in the Night mode will not be forwarded to TAS equipment in a satellite
node through the CCIS network. Therefore, the main node must provide TAS equipment for incoming
Central Office calls.
3. When Night mode is set at the main node, satellite nodes not equipped with an ATTENDANT CONSOLE
[A-3] can automatically be set to the Night mode by CENTRALIZED DAY/NIGHT MODE CHANGE -
CCIS [C-56] service.
4. A TAS indicator can be provided for each nodes incoming trunks.
5. An incoming call terminating in the Night mode will have the following order of priority:
a.) NIGHT CONNECTION - FLEXIBLE - CCIS [N-16],
b.) NIGHT CONNECTION - FIXED - CCIS [N-15],
c.) TRUNK ANSWER FROM ANY STATION - CCIS [T-27]. Incoming calls will overflow to TAS
[T-27], if this feature is provided, when the NIGHT CONNECTION FIXED/FLEXIBLE [N-1]
[N-2] [N-15] [N-16] stations are busy.
6. TAS indication will be activated for the LDN, WATS, FX, CCSA incoming calls.
7. TAS indication can be provided on a TENANT [T-12] basis.
8. Individual stations can be denied access to this feature via CLASS OF SERVICE - INDIVIDUAL [C-15].
9. If the system is changed to the Day mode while a TAS call is being indicated, a call terminating at a node
without an ATTENDANT CONSOLE [A-3] will not be transferred through the CCIS network to an
ATTENDANT CONSOLE [A-3].
10. This feature is also referred to as Universal Night Answer (UNA).
11. The TAS indicator must be locally provided.
12. All ATTENDANT CONSOLES [A-3] assigned to handle calls for a particular group of stations (whether
or not they belong to the same TENANT [T-12]) must have NIGHT CONNECTION [N-15, 16] set before
this feature will be activated.
    Add page 1083 to Favourites
    image text
    Enable zoom 
    							NEAX2400 IPX Feature Programming ManualPage 1040NDA-24297, Issue 1
T-27 Trunk Answer from Any Station - CCIS
Interactions
The system must be in the Night Mode for TAS to operate. Take into consideration the type of ATTENDANT
CONSOLE [A-3] system that is in service. Take special care when setting the resistance value via switch settings
on the PA-CS07 ATTENDANT CONSOLE [A-3] Circuit Card.
Programming
STEP 1:ASYD- SYS1, Index 68, bit 2. Type of TAS ringing; 0/1: Continuous/Interrupted.
SYS1, Index 77, bit 0. Is Day/Night change accomplished by removing ATTENDANT CONSOLE
[A-3] handset? 0/1: No/Yes.
STEP 2:ANPD- Reserve a number level for service feature access. Assign for Normal (N), Hooking (H) and
Busy (B). Assign NND in accordance with a predetermined numbering plan.
STEP 3:ASPA- Assign an access code to TRUNK ANSWER FROM ANY STATION, SRV = SSC (Service
Code), SID = 16 TAS. Connection Status CI = N, Normal (N).
STEP 4:ASFC- Assign station to receive TRUNK ANSWER FROM ANY STATION a Service Feature Class
that allows SFI = 13.
STEP 5:ACFR- Allow the types of incoming calls to be answered by TAS listed in Call Class Index (CCI) a
Transfer Service Feature Index of 5, TAS. The Call Class Indexes will correspond to ARTD, CDN
6:TCL; Trunk Class parameter.
CCI: 1 - LDN
2 - DDD2
3 - DDD3
4-TIELINE
5 - DDD4
STEP 6:ATA S- Assign the TAS circuit to the TN, LP, PIM, and the CKT #0/1 based on the circuit location.
TAS CKT # = ATTENDANT CONSOLE [A-3] CKT #.
    Add page 1084 to Favourites
    image text
    Enable zoom 
    							NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 1041
Uniform Numbering Plan - CCIS U-5
U-5  Uniform Numbering Plan - CCIS
General Description
In a CCIS network, a Uniform Numbering Plan enables a user to call any other station in the network using a
Uniform Numbering system. Two alternative numbering plans are provided:
In the first plan, the user dials a four or five-digit station number. The node in which the called station is
located is identified by either the first digit or the first two digits of the station number. More than one
location number can be assigned to a particular node.
In the second plan, the user dials a single-digit access code, a three-digit code identifying the particularnode
in the CCIS network, and a two, three, or four-digit station code.
Operating Procedure
To call a station at another office using Numbering Plan 1:
1. Lift the handset; receive dial tone.
2. Dial the four or five-digit telephone number.
3. The call is routed to another node according to programmed routing information, and the called station
rings.
4. The called station answers and the parties are connected.
To call a station at another office using Numbering Plan 2:
1. Lift the handset; receive dial tone.
2. Dial access code + office code - station code
:
X-XXX-XX, or
X-XXX-XXX, or
X-XXX-XXXX
3. The call is routed to the node designated by the Office Code. The called station rings.
4. The called station answers, and the parties are connected.
Service Conditions
1. Numbering Plan 1:
a.) All telephone numbers must be four or five digit numbers.
b.) The location of the PBX can be identified by either the first digit or the first two digits of the
telephone number.
2. Numbering Plan 2:
a.) The calling and called party’s LCD can display the office and station codes or the station code
only. This option is selected via the Maintenance Administration Terminal (MAT).
b.) Within the same PBX, a station-to-station call is made by simply dialing the two, three, or four-
digit telephone number.
3. The maximum number of digits per telephone number is eight.
    Add page 1085 to Favourites
    image text
    Enable zoom 
    							NEAX2400 IPX Feature Programming ManualPage 1042NDA-24297, Issue 1
U-5 Uniform Numbering Plan - CCIS
Interactions
If seven-digit Uniform Numbering Plans are used, an access code to the CCIS network may be added. Thus, a total
of eight digits will be dialed. For example, a user in Illinois wishes to reach a CCIS station number (753-4526) in
New York. Two options exist for network setup. The digit 8 may be programmed as a CCIS network access code,
such as a Least Cost Routing access code. The user then dials 8-753-4526. With this option, the 8 is assigned as the
CCIS access code. Digits 8-753 and all other CCIS office codes must then be listed in the AFRS command. The
second option is to program 753 as the CCIS access code, as in an LCR access code. If 753 is assigned as the CCIS
access code, then 753 and all other CCIS office codes must be listed in the AFRS command. In this case, the user
only dials 753-4526.
Programming
STEP 1:ARTD- The CCIS TIE Line voice/data route(s) over T-1 should be assigned as follows:
RT:1
2-ONSG :2 4-INSG :2 5-TF :3 6-TCL:4 7-L/T:1
8-RLP :2 13-AC :1 15-LSG :12 28-ANS:1 30-PAD:7 Optional
43-BT :1 49-TRKS :0/1* 50-DPLY :1
Note:When data“0”is assigned at one office, data“1”must be assigned at the opposite office.
The CCIS TIE Line signal link route(s) should be assigned as follows:
RT:2
6-TCL :4 7-L/T :1 9-TQ :*0 15-LSG:13 30-PAD:7 fixed
Note:* CDN 9:TQ is optional. Only use if an LCR route requires trunk queuing.
STEP 1:ARTD- The LCR Flag route should then be assigned as follows:
RT:31
6-TCL :1 7-L/T :1 9-TQ :1 13-AC :1
STEP 2:AT R K- Assign the LEN of the CCIS voice/data trunks, Route Number, Trunk Number, and Tenant
Number. The trunk LENs will correlate to channels 8-31 of the sub-highway in which the PA-24DTA/
24CCTA is mounted when 1.5M DTI/CCT is used. The LEN corresponding to the last level of the last
group is reserved for the CCIS signal link route.
STEP 3:MBTK- Assign the Make Idle status to the CCIS voice/data trunk.
Numbering Plan
STEP 4:ANPD- Reserve a number level for LCR. This level should correspond to the station numbering plan
of the opposite office. Assign for Normal (N) and Hooking (H) service. Number of Necessary Digits
will be the length of the digits assigned in ASPA.
STEP 5:ASPA- Assign the access code of the LCR flag route. Type of service, SRV= LCR (Least Cost
Routing), LEAST-COST ROUTING-3/6 DIGIT [L-5]. Assign the LCR flag route (usually route 31).
STEP 6:ARNP- Assign the physical route numbers (CCIS voice TIE Lines), as assigned in ARTD, and relate
these routes to the LCR access code as assigned in ASPA for SRV= LCR (Least Cost Routing). The
LCR access code is the first digit of the opposite offices’station numbers.
STEP 7:AMND- Assign the Maximum Necessary digits the system must translate for a proper route selection.
In this case, assign the first digit of the opposite system’s station numbering and the number of digits
in the station numbering plan.
STEP 8:AFRS- List the dialing patterns in groups that will be served by a specific sequence of routes. In this
case, the CCIS routes and the first digit of the station numbering will be considered. Also, if overflow
to DDD is used, the off-net numbers must be listed. These numbers will include the added digits from
the AOPR command. Assign this dialing sequence to an OPR.
    Add page 1086 to Favourites
    image text
    Enable zoom 
    							NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 1043
Uniform Numbering Plan - CCIS U-5
Programming (cont’d)
STEP 9:AO PR- The AFRS command designates the dialing sequence and the OPR to be selected. The AOPR
defines the routes and in what order these routes will be selected. In this case, the DTI routes will be
assigned. Also, it may be desirable to include DDD trunks as an overflow. Assign the following
parameters:
TDC NO. - Time-of-Day Pattern Change. Usually, this parameter does NOT apply and data“0”must
be entered. However, if different OPRs will be required as a function of time for an AFRS assignment,
designate 1-7 for which Time-of-Day Pattern Change Number (TDC NO) this OPR is assigned.
OPR No. - Outgoing Pattern Route. The number referenced in AFRS, consisting of a series of routes to
be chosen based on number dialed.
Route Advance Number(RA) - The order in which a route will be selected (0-7). Usually only one or
two routes are involved with DTI Tie lines.
Route Advance End Display - The last route in the route advance group. Indicate with data“0”.All
other routes are indicated by data“1”.
Route Number- The physical Route Number to be selected, as programmed in ARTD.
Skip Digits- Do Not skip any digits. Usually the LCR access code is the opposite system’s station
level. This digit must be sent to the opposite PBX.
If dialing pattern 2 is being used from the final node, send only the two, three, or four-digit station
number before the node dialed.
Pattern Number Location- Digits to be added after translating the dialed digits in AFRS. Go to
AADC command. This is usually not applicable to the DTI trunks, but will be used for DDD overflow.
Add a 1 if required, and possibly the area code.
Overflow Tone- Assign if a tone is wanted for the Last Choice Route. If so, assign data“1”for DDD.
Assign the primary RSC as data“0”.
STEP 10:ARRC- Assign trunk-to-trunk connection capabilities between the various CCIS routes within each
node of the network. Assign for both Alternative Route Index ARI-D-RES, Direct Connection and
ARI-A-RES, via the Attendant Console. Assign RES: 1, allowed.
STEP 11:ARNP- For Pattern 2 dialing, route 0 must be used to assign the access code and an office code to this
office. This information is transmitted to the D
termdisplay at the other offices of the network.
Therefore, when an incoming call is received at a distant office, the called party will recognize which
office is originating the call. This information will also appear in characters 96-103 in the SMDR
output for an O/G call record. It is also required for MESSAGE REMINDER - CCIS [M-34].
    Add page 1087 to Favourites
    image text
    Enable zoom 
    							NEAX2400 IPX Feature Programming ManualPage 1044NDA-24297, Issue 1
V-7 Voice Call - CCIS
V-7  Voice Call - CCIS
General Description
This service feature allows Inter-office VOICE CALL when the calling Dterm/Single-line Station and the called
Dtermbelong to different PBX’s in the CCIS network.
Operating Procedure
From a Dterm to a Dterm
1. Dterm(a) places a call to Dterm(b) through a CCIS line; receives ringback tone. Dterm(b) rings.
2. D
term(b) still does not answer. Dterm(a), then presses the VOICE key and sends a tone to Dterm(b). The
LCD on Dterm(a) displays:
Note:If Dterm(a) turns on MIC key on the Dterm,Dterm(a) can talk with Dterm(b) hands-free.
3. D
term(a) talks with Dterm(b) via the speaker.
Note:If Dterm(b) turns on MIC key on the Dterm,Dterm(b) can talk with Dterm(a) hands-free.
From a single-line station to a Dterm
1. Station (a) places a call to Dterm(b) through a CCIS line and receives ringback tone while Dterm(b) is
ringing.
N
ECNE C
Dterm (a)Dterm (b)
[Node B]
[Node A]CCIS RBT
RGRBT
called Dterm
VOICE XXXX
NE
CNEC
Dterm (a)Dterm (b)
[Node B] [Node A]CCISSpeakerVoice
NEC
STN (a)
Dterm (b)
[Node B]
[Node A]CCISRBT
RBT
RG
    Add page 1088 to Favourites
    image text
    Enable zoom 
    							NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1Page 1045
Voice Call - CCIS V-7
Operating Procedure (cont’d)
2. Station (a) switch hook flashes and receives special dial tone. Dterm(b) still does not answer.
3. Station (a) dial the Access Code of VOICE CALL service and sends out a signal tone to D
term(b) via the
speaker. Dterm(b) talks with Station (a) via the speaker.
Service Conditions
1. Once a VOICE CALL is executed, the message“VOICE on multi-line set”is displayed on the called
station.
2. Call Forwarding-All Calls/-Busy Line/-Don’t Answer can be serviced by VOICE CALL.
3. VOICE CALL will terminate at the station whose My-line equals the extension called.
Programming
Setting by VOICE button
STEP 1:AKYD-AssigndatatoFeaturekey.FKY=14
STEP 2:ADSL- Assign SN=2 (Originating; RBT Connection) and FKY=14 (Voice Call; VOICE).
This command is used for assigning the function to each soft key.
STEP 3:ASFC- With respect to SFC of the stations that set Voice Call, cancel the restriction of SFI= 52.
(SFI= 52: Voice Call service)
(SFI= 93: Voice Call Restrict)
Setting by SHF + Access Code (Individual Station)
STEP 1:ASYD- System 1, Index 17, bit 0: (1)
SHF + ACC Code during RBT.
STEP 2:ANPD- Assign minimum necessary number of digits for the first number of the Access Code of Voice
Call.
STEP 3:ASPA- Assigns Access Code of Voice Call.
CI= H (Hooking), SIDA= 41, SRV= SSCA (Service Code Appendix)
NEC
STN (a)
Dterm (b)
[Node B]
[Node A]CCISSPDT
SPDT
RG
NE
C
STN (a)
Dterm (b)
[Node B]
[Node A]Voice
    Add page 1089 to Favourites
    image text
    Enable zoom 
    							NEAX2400 IPX Feature Programming ManualPage 1046NDA-24297, Issue 1
This page is for your notes.
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax 2400 Ipx Feature Programming Manual