NEC Neax 2400 Imx Hotel Feature Programming Manual

							NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 157
Group Restriction G-21
G-21 Group Restriction
General Description
This feature allows the guest stations in a group to be restricted per the following conditions.
1. GROUP RESTRICTION is categorized as follows:
Outgoing Call Restriction Guest stations in a group are restricted from originating a call.
Outgoing Station Call Restriction Guest stations in a group are restricted from making a call to
stations in the other groups.
Outgoing C.O. Call Restriction Guest stations in a group are restricted from making a call to
outside parties.
Incoming Call Restriction Incoming calls to the guest stations in a group are restricted.
Incoming Station Call Restriction Incoming calls from guest stations in the other groups are
restricted.
Incoming C.O. Call Restriction Incoming calls from Central Office are restricted.
Outgoing and Incoming Call Restriction Outgoing calls from guest stations in a group and incoming
calls to the stations in a group are restricted.
2. Group to Group Connection:
If Group to Group Connection is assigned to a group with GROUP RESTRICTION, station calls to the
other groups are allowed.
3. Replacement of RSC:
RSC may be replaced while GROUP RESTRICTION is established, which allows selecting to restrict or
not according to RSC (in case of station calls) at each route (in case of C.O. calls).
4. All others:
a.) All restrictions clear
The entry of GROUP RESTRICTION/Group to Group Connection is cleared by one operation.
b.) Restriction check
The status of GROUP RESTRICTION is checked at the Console.
Operating Procedure
To set GROUP RESTRICTION from the Console:
Step Action Result
1
Press the GRS key.GRS lamp lights and the console display the title.
2Enter the select number for the required 
restriction.The console displays its title according to the select 
number.
3Enter the group number.
4Press the ENT key. “OK” and the restriction status are displayed. 
						

							NEAX2400 IMX Hotel Feature Programming Manual
Page 158ND-70284 (E), Issue 2
G-21 Group Restriction
Operating Procedure (cont’d)
To cancel GROUP RESTRICTION from the Console:
To set Group to Group connection from the Console:
To cancel Group to Group Connection from the Console:
To operate from the PMS terminal, follow the operating procedure for the PMS terminal.
a.) To set/cancel GROUP RESTRICTION
ORSC: Outgoing restriction service class
0 = to cancel Outgoing Call Restriction
1 = to set Outgoing Station Call Restriction and cancel Outgoing C.O. Call Restriction
2 = to cancel Outgoing Station Call Restriction and set Outgoing C.O. Call Restriction
3 = to set Outgoing Call Restriction
IRSC: Incoming restriction service class
0 = to cancel Incoming Call Restriction
1 = to set Incoming Station Call Restriction and cancel Incoming C.O. Call Restriction
2 = to cancel Incoming Station Call Restriction and set Incoming C.O. Call Restriction
3 = to set Incoming Call Restriction
b.) To set/cancel Group to Group Connection
GRPR: 0/1 = cancel/set
Step Action Result
1
Press the GRR key.The GRR lamp lights and the console displays the title.
2Enter the select number for the required 
restriction.The console displays its title according to the select 
Number.
3Enter the group number.
4Press the ENT key. “OK” and the restriction status are displayed.
Step Action Result
1
Press the GRS key.The GRS lamp lights and the console displays the title.
2Enter “8”. The console displays the title.
3Enter the group number A.
4Enter the group number B.
5Press the ENT key. “OK” is displayed.
Step Action Result
1
Press the GRR key.The GRR lamp lights and the console displays the title.
2Enter “8”.The console displays the title according to the select 
number.
3Enter the group number A.
4Enter the group number B.
5Press the ENT key. “OK” is displayed. 
						

							NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 159
Group Restriction G-21
Service Conditions
1. This service may not be provided for the guest rooms not checked in.
2. The maximum number of the groups which may be entered in GROUP RESTRICTION is 128.
3. Set/cancellation for GROUP RESTRICTION is available from the Console or according to texts from a
PMS terminal.
4. When the Console operator enters select numbers for restrictions, the following titles are displayed.
Outgoing Call Restriction OUTGOING ENT/CLR
Outgoing Station Call Restriction OG TO STA ENT/CLR
Outgoing C.O. Call Restriction OG TO CO ENT/CLR
Incoming Call Restriction INCOMING ENT/CLR
Incoming Station Call Restriction IC FROM STA ENT/CLR
Incoming C.O. Call Restriction IC FROM CO ENT/CLR
Outgoing and Incoming Call Restriction OG AND IC ENT/CLR
Group to Group Connection GRP:  GRP: 
All Restrictions Clear ALL RESTRICTION CLR
Restriction Check RESTRICTION CHECK
5. When a guest in a group checks out, the room comes out of GROUP RESTRICTION. When all guests in
a group checkout, GROUP RESTRICTION on this group is cleared.
6. A room added to the group after the entry of GROUP RESTRICTION is also restricted.
7. Station calls between rooms in the same group are permitted.
8. When both restrictions of Outgoing Station Call Restriction and Outgoing C.O. Call Restriction are set,
Outgoing Call Restriction is established. When Incoming Station Call Restriction and Incoming C.O. Call
Restriction are set, Incoming Call Restriction is established. Setting both restrictions of Outgoing Call
Restriction and Incoming Call Restriction is the same as setting Outgoing and Incoming Call Restriction.
9. In case a group uses replacement of RSC service, it must set an RSC for GROUP RESTRICTION (1 ~
15). In case replacement of RSC is not needed, “0” must be set.
10. When a call terminates to a guest station in a group with GROUP RESTRICTION, whether to restrict it
or not is decided according to the originating party as follows.
 When replacement of RSC is not assigned.
Originating PartyConnection
Guest station Restricted without condition.
ADM/Console Allowed without condition.
Outside Restricted without condition.
Another group Allowed if Group to Group Connection is entered. 
						

							NEAX2400 IMX Hotel Feature Programming Manual
Page 160ND-70284 (E), Issue 2
G-21 Group Restriction
Service Conditions (cont’d)
 When replacement of RSC is assigned.
11. The followings are significations of restriction status displayed on the Hotel Console. However, setting
status of Group to Group Connection is not displayed.
No display No entry
“SO” An entry of Outgoing Station Call Restriction exists
“CO” An entry of Outgoing C.O. Call Restriction exists
“OG” An entry of Outgoing Call Restriction exists
“SI” An entry of Incoming Station Call Restriction exists
“CI” An entry of Incoming C.O. Call Restriction exists
“IC” An entry of Incoming Call Restriction exists
12. When incoming calls from the Console are restricted with GROUP RESTRICTION, the operator can call
by pressing the DDO key.
13. If the entry of GROUP RESTRICTION cannot be read out from HP, the group is operated as if it is not
restricted.
14. When a call is transferred to the Console by GROUP RESTRICTION, its destination is the ICPT key.
15. Even if the call diversion is set by GROUP RESTRICTION, the transferred call and so on is not connected
to the diverted station. At this time, ROT is sent. In case of DIT from the Central Office, the current
restriction operation is performed. (The call terminates to the Console.)
16. The restriction status is listed in order of the entered group numbers.
17. When the group number which is not assigned Group to Group Connection is ordered to be listed,
“GROUP NOT ASSIGN” is printed. If any groups are not allowed Group to Group Connection, “ALLOW
GRP NOTHING” will print.
Interactions
1. GROUP RESTRICTION is not available when DO NOT DISTURB [D-11D] or RESTRICTION FROM
OUTGOING CALLS [R-4] service is provided.
a.) When DO NOT DISTURB is set to a station in the group restricted with Incoming Call
Restriction of GROUP RESTRICTIONS, the station is restricted with DO NOT DISTURB.
b.) When RESTRICTION FROM OUTGOING CALLS is set to a station in the group restricted with
Outgoing Call Restriction of GROUP RESTRICTION, the station is restricted with
RESTRICTION FROM OUTGOING CALLS.
Originating PartyConnection
Guest station Restricted according to restrictions of the replaced RSC.
ADM/Console Restricted according to restrictions of the replaced RSC.
OutsideRestricted according to restrictions of the replaced RSC.
If there is a restriction on the dummy route when the LCR service is 
used, any routes for outgoing calls are restricted.
Another groupAllowed if Group to Group Connection is entered.
If not, according to restrictions of the replaced RSC. When another 
group is also set GROUP RESTRICTION, according to restrictions of 
the replaced RSC between groups. 
						

							NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 161
Group Restriction G-21
Assignment Procedure
STEP CMND BIT EXPLANATION
Assign GRS, GRR Key
1AHSY
INDEX
114b
0
Not used b
1
b2
b3
b4
b5Console key designation
0/1 = Depending on SYS1, INDEX 160, Bit 3, Bit 4 (ASYD)/PI 115-126 (AHSY)
b
6Not used
b
7
Consecutive Dialing from Console
0/1 = Not Required/Required
If data “1” is assigned, switch settings for the ATI card are necessary.
2AHSY
INDEX
115~126
(Note)
Hotel Attendant Console Key Data
81H - WU SET 91H - CHECK-IN
82H - WU RESET 92H - CHECKOUT
83H - MW SET 93H -
84H - MW RESET 94H -
85H - DD SET 95H - C.O. CHANGE
86H - DD RESET 96H - BOSS/SET ENT
87H - RC SET 97H - BOSS/SEC RESET
88H - RC RESET 98H -
89H - STATUS 99H -
8AH - AUDIT 9AH -
8BH - 9BH -
8CH - 9CH -
8DH - 9DH -
8EH - 9EH -
8FH - 9FH - GRP IND. RESET
90H - A0H - GRP RESTRICTION SET
A1H - GRP RESTRICTION RESET
INDEX 121 122 123 124 125 126
INDEX 115 116 117 118 119 120
7118910
152364
ENTCEENDOperation Key
Operation Key
12 
						

							NEAX2400 IMX Hotel Feature Programming Manual
Page 162ND-70284 (E), Issue 2
G-21 Group Restriction
Assign Replacement Connection of RSC While the Restriction
3AHSY
INDEX
243b
0 
SO: Outgoing Station Call Restriction
b
1
b2
b3
b4SI: Incoming Station Call Restriction
b
5
b6
b7
4AHSY
INDEX
244b
0 
SOI: Outgoing/Incoming Station Call Restriction
b
1
b2
b3
b4
OG: Outgoing Call Restriction
b
5
b6
IC: Incoming Call Restriction
b
7
5AHSY
INDEX
246b
0 
CO: Outgoing C.O. Call Restriction
b
1
b2
b3
b4CI: Incoming C.O. Call Restriction
b
5
b6
b7
STEP CMND BIT EXPLANATION
b1b000ROT
01ATT
1 0 Announcement
1 1 Specified Station Call
b5b400ROT
01ATT
1 0 Announcement
1 1 Specified Station Call
b1b000ROT
01ATT
1 0 Announcement
1 1 Specified Station Call
b5b400ROT
01ATT
1 0 Announcement
1 1 Specified Station Call
b7b600ROT
01ATT
1 0 Announcement
1 1 Specified Station Call
b1b000ROT
01ATT
1 0 Announcement
1 1 Specified Station Call
b5b400ROT
01ATT
1 0 Announcement
1 1 Specified Station Call 
						

							NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 163
Group Restriction G-21
6AHSY
INDEX
247b
0 
COI: Outgoing/Incoming C.O. Call Restriction
b
1
b2
b3
b4
Not used b5
b6
b7SV: 0/1 = Service Out/In
7Assign Station Call Restriction for the replacement of RSC
Yes/No = Go to Step 8/Go to Step 7N
STEP CMND EXPLANATION
7N ASCRAssign Mutual Outgoing Station Call Restriction
Assign optional restriction data with the combination of the following station calls:
 Outgoing Station Call Restriction
 Incoming Station Call Restriction
 Outgoing/Incoming Station Call Restriction
8Assign C.O. Restriction for the Replacement of RSC “0”
Yes/No = Go to Step 9/Go to Step 8N.
8N ARSCAssign Route Restriction Class.
Assign optional restriction data with the combination of the following station calls:
 Outgoing C.O. Call Restriction
 Incoming C.O. Call Restriction
 Outgoing/Incoming C.O. Call Restriction
9Assign Restriction Connection to Specified Station Call
Yes/No = Go to Step 9Y Through 10/Go To Step 11.
9Y ASGDAssign equipment group information to specified incoming call
F = 1: Incoming Restriction
F = 2: Outgoing Restriction
10 ASIDAssign equipment information to specified incoming call
F = 1: Incoming Restriction
F = 2: Outgoing Restriction
11Assign Restriction Connection to Announcement.
Yes/No = Go To Step 11Y Through 16/The Procedure Ends Here.
11Y ARTDAssign Route Class Data
Assign trunk Route Data connecting with announcement machine
12 ATRKAssign Trunk Data
Assign Trunk Data connecting with announcement machine
13 MBTKAssign Make-Busy Data
Release Make-Busy for announcement trunk
14 ARSC Release Station and Announcement trunk restriction STEP CMND BIT EXPLANATION
b1b000ROT
01ATT
1 0 Announcement
1 1 Specified Station Call
END
END
END 
						

							NEAX2400 IMX Hotel Feature Programming Manual
Page 164ND-70284 (E), Issue 2
G-21 Group Restriction
Note 1:
It is necessary to assign data to the corresponding console keys when AHSY Index 114, Bit 5 is assigned.
Note 2:
If the Desk Console is used, the key indications and INDEXes are different from the NEAX2400 IMX Attendant
Console. Refer to the figure below. 15 ARRCAssign Alternative Route Restriction
Release incoming trunk and announcement trunk restriction
16 AAEDAssign Announcement Machine Data
Assign Group Restriction Data
EQP = 123: Group Outgoing Restriction
EQP = 122: Group Incoming Restriction STEP CMND EXPLANATION
INDEX122124123125121126Operation Key
INDEX
116118117119115120Operation Key 
						

							NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 165
Guest Station - DtermG-24
G-24 Guest Station - Dterm 
General Description
This feature allows the Dterm to be used as a guest station in the Hotel system. Various useful features such as
HANDS FREE ANSWER BACK - Dterm [H-4D] and MULTIPLE LINE OPERATION - Dterm [M-20D] have
become available for guest room stations.
In addition to time display, 
The Dterm LCD is used for the following Hotel services:
AUTOMATIC WAKE-UP [A-10]
CALLING STATION NUMBER DISPLAY [C-32]
2ND WAKE UP CALL [S-128]
DO NOT DISTURB [D-11]
ROOM CUTOFF [R-9]
MESSAGE WAITING [M-6]
MAID STATUS [M-22]
DIRECT DATA ENTRY - STATION [D-107]
Group Announcement for Automatic Wake Up
Operating Procedure
Refer to the associated pages with regard to the operation of each service.
Service Conditions
Refer to the associated pages with regard to the operation of each service.
Assignment Data
STEP CMND EXPLANATION
1 AGSTAssign station data for Guest Station D
term
TEC = 12 (Dterm) / 18 (Virtual Line)
Room Class = 15 (Guest Station)
STEP CMND BIT EXPLANATION
2AHSY
INDEX 
77b
0-/LCD Indication of Wake Up time on the Dterm
0/1 = -/Remains lit
b
1-/LCD Indication of Do Not Disturb on the Dterm
0/1 = -/Remains lit
b2-/LCD Indication of Room Cutoff on the Dterm
0/1 = -/Remains lit
b
3-/LCD Indication of 2nd Wake Up time on the Dterm
0/1 = -/Remains lit
b
4
Not used b5
b6
b7 
						

							NEAX2400 IMX Hotel Feature Programming Manual
Page 166ND-70284 (E), Issue 2
G-24 Guest Station - Dterm
3AHSY
INDEX 
105b
0Not used
b1
b2Maid Dial service from Console
0/1 = Not Required/Required
b
3Not used
b
4
Pattern of Wake Up time indication on the Console
0/1
 = 24 Hour/12 Hour System
Irrespective of data assignment for this bit, 24-hour time display is applied for Automatic Wake-
Up/2nd Wake Up Call.
b
5Not used
b6
b7Guest Name Display on Console
0/1 = Interface Type Model 60, 90, 120/Model 90, 120
4AHSY
INDEX 
139b
0Not used
b1
b2MW Lamp Indication of “Do Not Disturb”
0/1 = Lights Steadily/Flashes
b
3MW Lamp Indication of “Do Not Disturb”
0/1 = Not Required/Required
b
4MW Lamp Indication of “Message Waiting”
0/1 = Lights Steadily/Flashes
b
5MW Lamp Indication of “Message Waiting”
0/1 = Not Required/Required
b
6
2-Line Guest Name Display on a Dterm
0/1 = Out/In Service.
When this bit is assigned as “1”, Time Display disappears on the D
term while in conversation.
b
7Not used
STEP CMND EXPLANATION
5 AKYDAssign the following key data on the Guest Station D
term line/feature key
FKY 87 (Wake Up Set)
89 (Do Not Disturb Set)
91 (Room Cutoff Set)
93 (Message Waiting Set) STEP CMND BIT EXPLANATION