Lucent Technologies Definity Audix System Release 4.0 Screens Reference Manual

							DEFINITY AUDIX System Release 4.0 Screens Reference  585-300-213  Issue 1
May 1999
Screen Descriptions 
3-9 disable/enable Alarm-Origination 
3
disable/enable Alarm-Origination
The Disab le/Enab le Alarm-Orig ination sc reens are used  to temporarily d isable 
(or reenab le) the automatic  alarm rep orting  feature, take status of any alarms, 
and  test alarms. It is typ ic ally used  b y Luc ent Tec hnolog ies p ersonnel to d isab le 
alarm rep orting while troubleshooting  and  rep airing  the system. (Alarm 
orig ination is automatic ally re-enab led  when the log in that d isab led  it log s off.)
enable alarm-origination
 
disable alarm-origination
 
status alarm-origination
test alarm-origination
Pressing    (Enter) after initially entering  the sc reen will d isable (or reenab le) the 
alarm orig ination feature. 
NOTE:
This c ommand  req uires craft or hig her-level log in permissions.
 
Field Descriptions
This is a d isp lay only sc reen. There are no d ata entry field s. 
F3 
						

							DEFINITY AUDIX System Release 4.0 Screens Reference  585-300-213  Issue 1
May 1999
Screen Descriptions 
3-10 disable/enable Alarm-Origination 
3
status Alarm-Origination
The Status Alarm-Orig ination sc reen d isp lays the c urrent status of the alarm 
orig ination feature. 
status alarm-origination
 
NOTE:
This sc reen c an b e ac c essed while the DEFINITY AUDIX System is in the 
OA&M state.
Field Descriptions 
Field Name Description Valid Entries (display only)
alarm-orig ination Current alarm-orig ination state off (alarm orig ination is turned  off) 
active (an alarm c all in p rog ress) 
enab led  (alarm orig ination is enab led  
b ut c urrently id le) 
d isabled (alarm orig ination is 
temporarily disabled)
remote port status Current status of the remote 
acc ess p ort.Incoming, Outgoing , Idle 
d ata rate Currently ad ministered d ata 
transmission rate. 1200, 2400, 4800, 9600 
						

							DEFINITY AUDIX System Release 4.0 Screens Reference  585-300-213  Issue 1
May 1999
Screen Descriptions 
3-11 disable/enable Alarm-Origination 
3
test Alarm-Origination
The Test Results Orig ination sc reen initiates a d emand  alarm orig ination test and  
d isp lays the results of the test. 
test alarm-origination
nPress   (Enter) after initially entering  the sc reen to start the test. 
nPress   (Canc el) after initially entering  the sc reen to return the user to the 
c ommand  line without starting  the test. 
nPress   (Enter) after starting  the test to p ut the test in the bac kg round  
and  return the user to the c ommand  line. 
nPress   (Canc el) after starting  the test to abort the test and  return the 
user to the c ommand  line. 
NOTE:
This c ommand  req uires the craft or hig her-level login p ermissions.
F3
F1
F3
F1 
						

							DEFINITY AUDIX System Release 4.0 Screens Reference  585-300-213  Issue 1
May 1999
Screen Descriptions 
3-12 disable/enable Alarm-Origination 
3
Field Descriptions 
Field Name Description Valid Entries (display only)
Date Date and  time test was req uested .
Resourc e Typ e of resource b eing tested .
Loc . Loc ation of the alarm orig ination 
resourc e.7 c harac ter string  that 
ind icates port network, carrier, 
slot, and  p ort. For examp le, 
01a0201 ind icates 
p ort-network= 01, carrier= a, 
slot= 02, p ort= 01. 
Test Name Name of test b eing  exec uted .
Most Rec ent Test 
Res ul tCode ind ic ating  the results of the last 
tests run.b lank (test not exec uted)
R (test is running )
P (last test p assed
F (last test failed) 
A (last test ab orted ) 
Test Result String Ad ditional test result information.
Test Counters
Pass  No. of times the test has p assed  sinc e 
the test c ommand was exec uted . 
Fail  No. of times the test has failed sinc e the 
test c ommand  was exec uted . 
Abort  No. of times the test has ab orted  sinc e 
the test c ommand was exec uted .  
						

							DEFINITY AUDIX System Release 4.0 Screens Reference  585-300-213  Issue 1
May 1999
Screen Descriptions 
3-13 disable/enable Alarm-Origination 
3
Additional Specifications
While the test is running , you have three op tions: 
1. Press   (Canc el) to ab ort the test and  return to the c ommand  line. 
2. Wait for the test to c omp lete. 
3. Press   (Enter) to p ut the test in the b ac kg round  and  return to the 
c ommand  line. 
Ty p e  status test
 to rec onnec t to the sc reen of a test running  in b ac kg round , or to 
d isp lay the results of the most rec ently c omp leted  test. 
A one-minute d elay is availab le to allow remote testing  (test will fail b usy if you 
are logg ed  on remotely.) To use this test feature:
1. Start test.
2. Put in b ac kg round .
3. Logoff.
4. Log  b ac k in after one minute.
5. Check log for pass/fail status.
F1
F3 
						

							DEFINITY AUDIX System Release 4.0 Screens Reference  585-300-213  Issue 1
May 1999
Screen Descriptions 
3-14 display Alarms 
3
display Alarms
Th e Alarm Rep ort sc reen d isp lays ac tive or resolved  DEFINITY AUDIX System 
alarms. 
display alarms
The Alarm Rep ort sc reen has two p ag es as shown b elow. Use the first pag e to 
sp ec ify whic h alarms will b e d isp layed  in the rep ort. 
						

							DEFINITY AUDIX System Release 4.0 Screens Reference  585-300-213  Issue 1
May 1999
Screen Descriptions 
3-15 display Alarms 
3
The sec ond  p ag e d isp lays the req uested alarm information.
Field Descriptions 
Field Name Description Valid Entries
NOTE:
The first time this sc reen is used after a restart or reb oot, the field s on the 
selec tion pag e of the sc reen are b lank. Sub seq uently, eac h field on the 
selec tion pag e of the sc reen is p op ulated  with the value entered the last 
time the sc reen was used .
SELECTION PAGE
ALARM TYPES
 Active? Disp lays ac tive alarms in the alarm report.  y (d isplay active alarms) 
n (not d isp lay ac tive 
alarms)
NOTE:
There must be a y in either the Ac tive field or the Resolved ? field  for 
alarm entries to b e d isp layed  in the rep ort. You must req uest either 
ac tive or resolved alarms, b ut not b oth alarms simultaneously. 
						

							DEFINITY AUDIX System Release 4.0 Screens Reference  585-300-213  Issue 1
May 1999
Screen Descriptions 
3-16 display Alarms 
3
Resolved ?  Disp lays resolved  alarms in the alarm rep ort.  y (d isplay resolved  alarms)
n (not d isp lay resolved  
alarms)
NOTE:
You may req uest major alarm, minor alarm, warning , or any 
comb ination of these for a report.
Major? Disp lays major alarms in the alarm rep ort.  y (d isplay major alarms)
n (not d isp lay major 
alarms) 
Minor? Disp lays minor alarms in the alarm rep ort.  y (d isplay minor alarms)
n (not d isp lay minor 
alarms)
Warning ? Disp lays warning s in the alarm rep ort.  y (d isplay warnings) 
n (not d isp lay warning s)
Start Date Beg inning  d ate for the alarm report.
yy <  70 is assumed  to b e the 21st c entury.blank (d isp lays all ac tive or 
resolved  alarms) 
date in mm/d d /yy format 
Time Beg inning  hour and  minute of the g iven d ay 
for the alarm report. The Start Date field  must 
have valid  entries before this field  can b e 
used.blank (d isp lays all alarms 
for the spec ified  Start Date)
time in hh:mm format
Resourc e Typ e Spec ific typ e of alarmed  resource for the 
alarm rep ort. If this field contains a resource 
typ e, only alarms related  to the sp ec ified  
resourc e type are d isplayed .any resource type defined 
in 
DEFINITY AUDIX System 
Release 4.0 Maintenance
, 
585-300-121. 
Loc ation Further sp ecifies the alarm rep ort b y 
req uesting  a DEFINITY AUDIX System 
loc ation for the fault resource typ e. If this 
field c ontains a location, the Resource Typ e 
field  must c ontain a value. Disp lays only 
alarms related  to the sp ecified  resourc e typ e 
and  loc ation. To view valid  locations for this 
system, ac c ess list configuration or 
display voice group screen.5 to 7 charac ter p ort 
ad d ress of the sc reen 
port-network (2 d igits), 
carrier (1 letter), slot (2 
dig its), and p ort (2 dig its). 
For examp le, 01a0201 
sp ec ifies a p ort location as 
follows: p ort-network= 01, 
carrier= a, slot= 02, and  
port=01. 
NOTE:
A b oard  location consists of only five c haracters that sp ec ify the 
port-network, the carrier, and  the slot. If the first five c haracters 
sp ec ify a valid b oard  location, entering  d ig its in the 6th and  7th 
positions (for a port) will generate an error message. A p ort loc ation 
req uires all seven charac ters. Valid  ranges are:
Port-network 0 - 99 
Carrier   A - E 
Slot   01 - 24 
Port   01 - 24 Field Name Description Valid Entries 
						

							DEFINITY AUDIX System Release 4.0 Screens Reference  585-300-213  Issue 1
May 1999
Screen Descriptions 
3-17 display Alarms 
3
Fault Code Fault c ode for the g iven resource type. If this 
field c ontains a fault c od e, d isp lays only 
alarms with this fault c od e.0 - 9999
NOTE:
Eac h resource typ e has its own set of fault c od es. Therefore, 
sp ec ifying  a fault cod e without a resourc e type name c an d isplay 
multiple resourc e typ es with the same fault c ode. 
DISPLAY PAGE 
Resourc e Typ e Spec ific typ e of alarmed  resource. Possible values in this field 
are any resourc e typ e 
defined  in 
DEFINITY 
AUDIX System Release 4.0 
Maintenanc e
, 
585-300-121.
Loc ation 5 to 7 c haracter location for the fault 
resourc e type.
Alm Lvl Alarm severity level. MAJ (major), MIN (minor), 
WRN (warning) 
Fault Code Fault c od e for a spec ific alarm for the given 
resourc e type. Eac h resourc e type has its 
own set of fault c od es.0 to 9999
Ack Ind icates whether the alarm was p resent 
d uring  the last alarm orig ination c all, i.e., the 
alarm has b een reported  to the servic es 
org anization. However, alarms may not have 
b een sent if there were a sig nificant numb er 
of hig her p riority alarms. y (alarm was p resent 
during  the last referral c all) 
n (alarm was not p resent 
during  the last referral c all)
Date/Time Alarmed Date and  time the alarm was raised  against 
the g iven resourc e. This field  should  always 
have a value. If the Date/Time Resolved 
field s are b lank, the alarm 
is c urrently ac tive. 
Date/Time Resolved Date and  the time the alarm was resolved  If 
these fields are blank, the alarm is c urrently 
active. If only ac tive alarms are 
displayed, these fields 
should always be blank.
If only resolved alarms are 
disp layed, this field should  
always have a value.
Resolve Reason Cause of the alarm resolution. This field  is 
b lank for active alarms.Maint (resolved by 
maintenanc e, resourc e 
rec overed .) 
Reb oot (system reb ooted . 
All ac tive alarms resolved .
Remove (alarm resolved by 
removing  the resource.  Field Name Description Valid Entries 
						

							DEFINITY AUDIX System Release 4.0 Screens Reference  585-300-213  Issue 1
May 1999
Screen Descriptions 
3-18 add Announcement-Set 
3
add Announcement-Set
The Announc ement Set sc reens are used to add , remove, c op y or list an 
announc ement set. 
add announcement set
 
annc-set-name 
remove announcement set
 
annc-set-name 
copy announcement set 
annc-set-name
list announcement set annc-set-name
Th e  announcement-set-name is the name of the announc ement set to b e ac ted  
up on.
Field Descriptions 
Field Name Description (display only)
Announc ement Set Name of the announcement set b eing ad ded  or removed , as entered on 
the c ommand  line. For add, the annc. set named by 
annc-set-name must 
not exist and  must be touc h-tone unique with other existing  annc. set 
names. For remove, the annc . set named b y 
annc-set-name must exist 
and  must not b e the active annc. set.