Kyocera FS 1028MFP User Manual

							Preparation before Use 
OPERATION GUIDE2-15
2
17Press the U or V  key to select [O ff] and then press 
the  OK key. 
Completed.  is displayed and the screen returns to 
the IPv4 Setting menu.
18Press the  U or  V key to select [IP Address].
19Press the  OK key. IP Address appears.
20Use the arrow keys to enter the IP address. 
Press the  Y or  Z key to move the cursor position 
horizontally.
Press the  U or  V key or the numeric keys to enter 
the IP Address. Each 3 digits can be set between 
000 and 255.
IMPORTANT:  When the DHCP Setting ( page 2-18) is 
[On], the current IP address is displayed and cannot be 
changed.
When setting an IP address, set the DHCP Setting 
( page 2-18 ) to Off.
21Press the OK key.  Completed.  is displayed and the 
screen returns to the  IPv4 Setting menu.
22Press the U or  V key to select [Subnet Mask].
IPv4 Setting:a  b 
1  DHCP
2  Bonjour
*********************
[ Exit ]
3  IP Address
IP Address:
a  b 
   123.145.167.
189
IP Address:  b 
   123.145.167.189
IPv4 Setting:a  b 
3  IP Address
*********************
5  Default Gateway [ Exit ]
4  Subnet Mask
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use 
2-16OPERATION GUIDE
23Press the OK key. Subnet Mask appears.
24Use the arrow keys to enter the Subnet Mask.
Press the  Y or  Z key to move the cursor position 
horizontally.
Press the  U or  V key or the numeric keys to enter 
the Subnet Mask. Each 3 digits can be set between 
000 and 255.
IMPORTANT:  When the DHCP Setting ( page 2-18) is 
[On], the current Subnet Mask is displayed and cannot 
be changed.
When setting an Subnet Mask, set the DHCP Setting 
( page 2-18 ) to Off.
25Press the OK key.  Completed.  is displayed and the 
screen returns to the  IPv4 Setting menu.
26Press the U or  V key to select [D efault Gateway].
27Press the OK key. Default Gateway appears.
28Use the arrow keys to enter the Default Gateway.
Press the  Y or  Z key to move the cursor position 
horizontally.
Press the  U or  V key or the numeric keys to enter 
the Default Gateway. Each  3 digits can be set 
between 000 and 255.
Subnet Mask:a  b 
   123.145.167.
189
IPv4 Setting:a  b 
3  IP Address
4  Subnet Mask
*********************
[ Exit ]
5  Default Gateway
Default Gateway:
a  b 
   123.145.167.
189
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use 
OPERATION GUIDE2-17
2
IMPORTANT: When the DHCP Setting ( page 2-18) is 
[On], the current Default Gateway is displayed and 
cannot be changed.
When setting an Default Gateway, set the DHCP 
Setting (page 2-18 ) to Off.
29Press the OK key.  Completed.  is displayed and the 
screen returns to the  IPv4 Setting menu.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use 
2-18OPERATION GUIDE
DHCP Settings
Select whether or not to use the DH
CP server. The default setting is On.
Use the procedure below to  specify the DHCP setting.
1Press the System Menu/Counter  key on the main 
unit operation panel.
When you are performing user management and 
have not logged in, a login screen will appear. 
Then, enter the user ID and password to log in.
NOTE: 
• Refer to Character Entry Method on Appendix-5  for 
details on entering characters.
• If [Netwk Authentic.] is  selected as the user 
authentication method, press [Menu] (the Left 
Select  key) to select the au thentication destination.
2In the Sys. Menu/Count. menu, press the  U or  V 
key to select [System], and then press the OK  key.
IMPORTANT: To make the settin gs, you must have 
logged in using a user ID  with administrator privileges.
If you have logged in using a user ID without 
administrator privileges,  the screen will display 
Administrator only. and return to the standby screen.
3In the System menu, press the U  or V key to select 
[Network Setting].
Login User Name:L  b 
 
********************
Login Password:
[ Menu ] [ Login ]
Sys. Menu/Count.:a  b 
1  Report
2  Counter
*********************
 [ Exit ]
3  System
Administrator only.
System:a  b 
*********************
2  I/F Block Set.
3  Security Level [ Exit ]
1  Network Setting
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use 
OPERATION GUIDE2-19
2
4Press the OK key. The Network Setting menu 
appears.
5Press the  U or  V key to select [TCP/IP Settings].
6Press the  OK key. The TCP/IP Settings menu 
appears.
7Press the  U or  V key to select [TCP/IP].
8Press the  OK key. TCP/IP appears.
9Press the  U or V  key to select [On] and then press 
the  OK key.
Completed.  is displayed and the screen returns to 
the TCP/IP Settings menu.
10Press the  U or  V key to select [IPv4 Setting].
11Press the  OK key. The IPv4 Setting menu appears.
12Press the  U or  V key to select [DHCP].
Network Setting:a  b 
*********************
2  NetWare
3  AppleTalk
[ Exit ]
1  TCP/IP Settings
TCP/IP Settings:
a  b 
*********************
2  IPv4 Setting
3  IPv6 Setting [ Exit ]
1  TCP/IP
TCP/IP:
a  b 
1  Off
*********************2 *On
TCP/IP Settings:
a  b 
1  TCP/IP
*********************
3  IPv6 Setting [ Exit ]
2  IPv4 Setting
IPv4 Setting:
a  b 
*********************
2  Bonjour
3  IP Address [ Exit ]
1  DHCP
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use 
2-20OPERATION GUIDE
13Press the OK key. DHCP appears.
14Press the  U or  V key to select [On] or [Off] and 
then press the  OK key.
Completed.  is displayed and the screen returns to 
the IPv4 Setting menu.
Bonjour Settings
Select whether or not to use Bonjour. The default setting is  Off.
Use the procedure below to specify the Bonjour setting.
1Press the  System Menu/Counter  key on the main 
unit operation panel.
When you are performing user management and 
have not logged in, a login screen will appear. 
Then, enter the user ID and password to log in.
NOTE: 
• Refer to Character Entry Method on Appendix-5  for 
details on entering characters.
• If [Netwk Authentic.] is  selected as the user 
authentication method, press [Menu] (the Left 
Select  key) to select the au thentication destination.
2In the Sys. Menu/Count. menu, press the  U or  V 
key to select [System], and then press the OK  key.
IMPORTANT: To make the settin gs, you must have 
logged in using a user ID  with administrator privileges.
If you have logged in using a user ID without 
administrator privileges,  the screen will display 
Administrator only. and return to the standby screen.
DHCP:a  b 
1  Off
*********************2 *On
Login User Name:L  b 
 
********************
Login Password:
[ Menu ] [ Login ]
Sys. Menu/Count.:a  b 
1  Report
2  Counter
*********************
 [ Exit ]
3  System
Administrator only.
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use 
OPERATION GUIDE2-21
2
3In the System menu, press the U or V key to select 
[Network Setting].
4Press the  OK key. The Network Setting menu 
appears.
5Press the  U or  V key to select [TCP/IP Settings].
6Press the  OK key. The TCP/IP Settings menu 
appears.
7Press the  U or  V key to select [TCP/IP].
8Press the  OK key. TCP/IP appears.
9Press the  U or V  key to select [On] and then press 
the  OK key. 
Completed.  is displayed and the screen returns to 
the TCP/IP Settings menu.
10Press the  U or  V key to select [IPv4 Setting].
System:a  b 
*********************
2  I/F Block Set.
3  Security Level
[ Exit ]
1  Network Setting
Network Setting:
a  b 
*********************
2  NetWare
3  AppleTalk [ Exit ]
1  TCP/IP Settings
TCP/IP Settings:
a  b 
*********************
2  IPv4 Setting
3  IPv6 Setting [ Exit ]
1  TCP/IP
TCP/IP:
a  b 
*********************
2 *On
1  Off
TCP/IP Settings:
a  b 
1  TCP/IP
*********************
3  IPv6 Setting [ Exit ]
2  IPv4 Setting
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use 
2-22OPERATION GUIDE
11Press the OK key. The IPv4 Setting menu appears.
12Press the  U or  V key to select [Bonjour].
13Press the  OK key. Bonjour appears.
14Press the  U or  V key to select [On] or [Off] and 
then press the  OK key.
Completed.  is displayed and the screen returns to 
the IPv4 Setting menu.
AppleTalk Setup
Select the Apple Talk network connection. The default setting is  On.
Use the procedure below to setup the AppleTalk setting.
1Press the  System Menu/Counter  key on the main 
unit operation panel.
When you are performing user management and 
have not logged in, a login screen will appear. 
Then, enter the user ID and password to log in.
NOTE: 
• Refer to Character Entry Method on Appendix-5  for 
details on entering characters.
• If [Netwk Authentic.] is  selected as the user 
authentication method, press [Menu] (the Left 
Select  key) to select the au thentication destination.
IPv4 Setting:a  b 
1  DHCP
*********************
3  IP Address
[ Exit ]
2  Bonjour
Bonjour:
a  b 
*********************
2  On
1 *Off
Login User Name:L  b 
 
********************
Login Password:
[ Menu ] [ Login ]
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use 
OPERATION GUIDE2-23
2
2In the Sys. Menu/Count. menu, press the U or  V 
key to select [System], and then press the OK  key.
IMPORTANT: To make the settin gs, you must have 
logged in using a user ID  with administrator privileges.
If you have logged in using a user ID without 
administrator privileges,  the screen will display 
Administrator only.  and return to the standby screen.
3In the System menu, press the U  or V key to select 
[Network Setting].
4Press the  OK key. The Network Setting menu 
appears.
5Press the  U or  V key to select [AppleTalk].
6Press the  OK key. AppleTalk appears.
7Press the  U or  V key to select [On] or [Off] and 
then press the  OK key.
Completed.  is displayed and the screen returns to 
the Network Setting menu.
Sys. Menu/Count.:a  b 
1  Report
2  Counter
*********************
 [ Exit ]
3  System
Administrator only.
System:a  b 
*********************
2  I/F Block Set.
3  Security Level [ Exit ]
1  Network Setting
Network Setting:
a  b 
*********************
2  NetWare
3  AppleTalk [ Exit ]
1  TCP/IP Settings
AppleTalk 
          a  b 
1  Off
*********************2 *On
Downloaded From ManualsPrinter.com Manuals 
						

							Preparation before Use 
2-24OPERATION GUIDE
Installing Software
Install appropriate software on your PC from the included Product Library CD-ROM (Product Library) if you want 
to use the printer function of this machine or perform  TWAIN / WIA transmission or FAX transmission from your 
PC. 
NOTE: Installation on Windows XP, Windows 2000, Server 2003 and Windows Vista must be done by a user 
logged on with administrator privileges.
Plug and Play is disabled on this device when in Sle ep Mode. Wake the device from Low Power Mode or Sleep 
Mode before continuing. See Auto Low Power Mode on page 3-4  and Sleep and Auto Sleep on page 3-5 .
FAX functions available only in FS-1128MFP.
Downloaded From ManualsPrinter.com Manuals