Vodavi Starplus Dhs-l Technical Manual

							Programming3-21
Chapt er 3 - Key Station Featu res , Opera tion , an d Programmin g
Table 3-6: S ta tion Application Programming Table
S T A T I O N APPL ICATI ON R an ge De fa ul t De scri pti on
1.
UCD PROGRAMM ING
UCD Group 1-24 24 UCD groups are a llowed in the system.
Te nant 1-6 1 T he tena nt group to which the UCD group is
assigned.
UCD Attri b UCD/VA UCD T his de fi ne s the hunt group ty pe.
2.
UCD GROUP M EMBER
Me mb er Any v alid s tation
numbe rEach UCD group may has 24 members in it.
Hunt Me thod Line /Dist/A ll Line T here a re 3 hunting me thods al lowe d: Li near
( LINE ) Dis tributed DIS T ) A ll Ring (A LL) .
No Ans Tim e 5-6 0 1 0 T his option de fine s the length of time a call
will ring a m em ber of the group be fore
a dvancing to the ne xt me mb er.
O ver 1 Tim er 0-255 0 T his tim er dete rmine s the le ngth of ti me that
a ca ll will ring in the UCD group be f ore being
transferred to the ov erflow 1 de stina ti on I f
the time r is s et to 0 the n it wil l not ove rf low
to the ove rf low 1 des tination.
Ov er 1 D es t N u ll T h is is t h e ov er f lo w 1 des t in at io n an d c an be a ny
va lid s ta tion numbe r or a nother UCD group.
Ov er 2 Tim er 0 -25 5 0 T his is the s am e as the ove r 1 tim er exce pt it
overflows to the over 2 destination.
Ov er 2 D es t N u ll S am e as o ver 1 des t in at io n .
Ov er Counter 1 -12 8 1 T his option de fine s how ma ny time s a
u n a n sw er ed c all c yc le s t o t h e ov er f lo w 2
de stina tion before going to the re route
de stina tion.
Re route Des t Null T his option de fine s the fi nal des tination f or
una nsw ered c alls to a group. This option is
used only whe n:
†No overflow 2 destination is defined a nd
the cal l re ma ined una nswere d by
des tination 1 .
†T he ca ll rem aine d una nswere d by the
overflow 2 destination after the overflow
count ha s e xpired.
T he reroute can be a ny exte nsi on or anothe r
UCD group. 
						

							3-22Programming
Ch apter 3 - Key Station Featu res , Operation , an d P rog rammin g
3.
VOIC E MA IL
VM Hunt Group 0/1-24 0 T he voice mail ports must be programmed in
auniqueUCD group.TheVMHUNTgroup
a nd the UCD groups m ust be the same
group ( i.e: VM hunt group 1 = UCD group 1).
Prefix Table T here a re 10 pre fix ta ble s that can be se nt to
the VM in certa in conditions. The pref ix
code s a re up to 4 digits in length a nd can
includ e 0-9,*, # , a nd Pa use (P).
ICM /VM Null T his pref ix is s ent to the VM prior to the us e r’s
e xtension numbe r whe n check ing me ssage s.
Trans f er Null T his pref ix is s ent to the VM prior to the us e r’s
e xtension numbe r whe n a cal l is transfe rred
dire ctly to the m ailbox.
Dire ct Fwd. Null
Bus y Fw d. Null T his pref ix is s ent to the VM prior to the us e r’s
e xtension numbe r whe n the transferred ca ll
goes to an extension that is in a busy call
forward mode to the VM group.
No_A ns F wd. Null T his pref ix is s ent to the VM prior to the us e r’s
e xtension numbe r whe n the transferred ca ll
goe s to an e xtension that is in a no answe r
forward mode to the VM group.
DND Fwd. Null T his prefix is sent to the VM prior to the use r’s
e xtension numbe r whe n the transferred ca ll
goe s to an e xtension that has DND enabl ed
to the VM group.
LN Re call Null
UCD Ov erflow Null T his pre fix is sent to the VM prior to the UCD
group transferring a ca ll from overflow to the
VM group.
Record Dgt Null
Cle ar Ms g
ICM Suf fix
XF ER Suf fi x Null
DIS Digit Null
Table 3-6: S ta tion Application Programming Table
S T A T I O N APPL ICATI ON R an ge De fa ul t De scri pti on 
						

							Programming3-23
Chapt er 3 - Key Station Featu res , Opera tion , an d Programmin g
Table 3-7: Line Application Programming Table
L I N E APPLICATION Range Default Description
1.
TRUNK ROUTE System allows 24 different trunk groups.
Trunk Route 01-24 - S elect a trunk group number.
PBXCode 0-9 9 Trunksprogrammed asPBXtype,thePBXcode
is not subje ct to Toll Re stric tion.
PCS S endi ng Y/N Y T he pe riodic Clea ring Signa l (PCS ) al lows the
ca lling party to ha ng-up a nd imm edia tely
te rminate the CO ca ll.
Hunt Method S EQL/ RA N/SE QF S EQL De term ines ord er that trunks are sele cted.
S EQF =lst trunk i n group
S EQL= sequentia l from last trunk
RAN= random from la st trunk used
A lternate Route
Al ter Route 1/2 - 2 alterna te routes are used when a ll trunk
routes are b usy.
Route Numb er 01-24 - E nte r route numbe r use d as alterna te.
De lete Di gits 0 --9 0 Up to 1 6 digits may be dele ted from d ial string.
( May be use d to acces s l ong di stance
provide rs.)
Inserte d Digits - - Up to 16 digits may b e inserte d from dial
s tring. ( May be us ed to acce ss long dista nce
provide rs.)
DIR # S WAP 9 T his option rea ss igns the directory num be r f or
the trunk route .
Sw ap W ith - - Not program mabl e as this tim e.
2.
T1 CAR DSy ste m al low s 24 T1 lines .
Parameter Set
Fram ing Type D4 /ES F D4
Enco de AMI /B8 Z S/ No ne A MI
Si gnal DT MF/Pulse DTMF
DID Le ngth 3-10 3
Dial Tone Y/N Y
Remote Station
Le ading Numb er 1- 9 -
Route Numb er 0-24 0
ºDe lete Di gits 0--9 0 
						

							3-24Programming
Ch apter 3 - Key Station Featu res , Operation , an d P rog rammin g
2.
ºIns erte d Digits - -
Cha nnel Type
Show Line 772-795 - E nte r vali d T 1 l ine numb er.
Cha n Ty pe Loop/Ground/
DID/I_ E&M /
W_E&M/NoneLoop
ANI N/Y N
Trans Tab As s ign Trans lation Tab le A ss ignme nt
Show Tenant 1-6 -
ºTo In c r ea se 0 - 15 0 15 0 ( To lo w er valu e , g o t o D e c r eas e t a ble v alu es )
ºTo Decrease 150-0 150 (To lower value, go to Increase tabl e val ues.)
Trans Tab P rog Trans lation Tab le P rogra mm ing
Show Tenant 1-6 -
ºInte rce pt 20 1-2 72
30 1- 3 72
43 0- 4 53E nte r a va lid sta tion or Hunt group numbe r.
ºDigit Inte rval 01-99 -
ºIncom - - Incom ing numbe r
ºDest - - Hit [chg] then enter desired station or Hunt
group numb er.
3.
IC L IDIn orde r for the IC LID fe ature to ope rate the
RS2 3 2-1 port mus t be s et f or I CLID. Attenda nt
program ming ( F# 0) is us ed to e nable the port
function.
Line Numbe r Ta b. Cross-refe re nces the trunk dire ctory num ber
to the num ber provide d from the Call er ID box.
Sh o w Li n e 70 0- 7 71 -
Line Numbe r 0 - 72 0
Table 3-7: Line Application Programming Table
L I N E APPLICATION Range Default Description 
						

							Programming3-25
Chapt er 3 - Key Station Featu res , Opera tion , an d Programmin g
Table 3-8: System Application Programming Table
SYSTEM APPLICATION Range Default Description
1.
RING SC HEME 0-4 2
2.
L ET TE R TYPE 0-7 0 Not a pplicabl e - do not cha nge.
3.
HOUR MODE 12 /2 4 24 Sel ect s tandard or m ilitary ti me.
4.
P OS ITI ON TO D IR Exa mple :
1- 0 4- 0 1= st a t i o n 20 1This s etting is us ed to change s tation/CO line
numbers per their physical location. Enter
position as Cab inet/S lot/Port. (Cabine t
number will always be number 1.)
Di r Num ber Displa ys DIR num ber of port at spe cif ied
addres s.
5.
DI R TO PO SIT ION Enter va lid DIR numbe r of a s tation/line .
Posi tion Displa ys physical l ocation of speci fied DIR
nu m b e r.
6.
NUMBE RI NG PLAN
Trunk Route The 24 trunk route s can be acce ssed using
the5differentprogrammabledirectory
nu m b e r s.
Le ngth 1-4 1 The le ngth of the directory num be r ca n be
fr o m 1 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 9 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
S ta Dir Numbe r Stations can be a cces se d using up to 9
diff er e n t dir ec t o r y n um be r s.
Le ngth 2-4 3 The le ngth of the directory num be r ca n be
fr o m 2 t o 4 d i g i t s .
Le ading 1 - 4 ( 1- 9 ) 2 and 3 Any digit 1- 9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
S ta Page Group The 24 Page groups are accessed using the
following director y numbers.
Le ngth 2-4 3 The le ngth of the directory num be r ca n be
fr o m 2 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 40 , 41 , 42 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s. 
						

							3-26Programming
Ch apter 3 - Key Station Featu res , Operation , an d P rog rammin g
6. S ta Hunt Group The 24 UCD groups are a ccesse d using the
following director y numbers.
Le ngth 2-4 3 The le ngth of the directory num be r ca n be
fr o m 2 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 43 , 44 , 45 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
S ta Pickup Group The 24 Pickup groups are a ccessed using the
following director y numbers.
Le ngth 2-4 3 The le ngth of the directory num be r ca n be
fr o m 2 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 46 , 47 , 48 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
I ndiv Ab br Num ber The indi vidual s pe ed dia l num be rs are
accessed usingthe following directory
nu m b e r s.
Le ngth 2-4 3 The le ngth of the directory num be r ca n be
fr o m 2 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 5 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
C om mon A bbr Numbe r The com mon s pee d dial num bers are
accessed usingthe following numbers.
Le ngth 2-4 3 The le ngth of the directory num be r ca n be
fr o m 2 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 6 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
L ine Dir Numb er Each trunk has a unique access num be r tha t
is acce ss ed by dia ling the follow ing directory
nu m b e r.
Le ngth 2-4 3 The le ngth of the directory num be r ca n be
fr o m 2 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 7 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
Table 3-8: System Application Programming Table
SYSTEM APPLICATION Range Default Description 
						

							Programming3-27
Chapt er 3 - Key Station Featu res , Opera tion , an d Programmin g
6 . M u si c S o u rc e Th e m u si c c i r c u i t s ar e us e d f o r bac k g ro u n d
mus ic. T he circuits are a cces se d using the
follow ing director y numbe r.
Le ngth 2-4 3 The le ngth of the directory num be r ca n be
fr o m 2 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 8 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
L oud Be ll The loud be ll circuits are ac ce s se d using the
following director y numbers. The directory
num be r i s use d in the a nswering position to
si g n a l a l o u d bel l .
Le ngth 2-4 3 The le ngth of the directory num be r ca n be
fr o m 2 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 81 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
E xte rnal Pa ger The e xterna l paging circuits are a ccesse d
us ing the f ollow ing directory num be r.
Le ngth 2-4 3 The le ngth of the directory num be r ca n be
fr o m 2 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 82 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
V irtual Numb er Not used a t this time .
Le ngth 2-4 3 The le ngth of the directory num be r ca n be
fr o m 2 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 83 , 84 , 85 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
O perator Code The f ollow ing cod e is us e d to a cces s the
station program me d as the atte ndant.
Le ngth 1-4 1 The le ngth of the directory num be r ca n be
fr o m 1 t o 4 d i g i t s .
Le ading 1 -4 ( 0-9 ) 0 Any digit 0-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
Table 3-8: System Application Programming Table
SYSTEM APPLICATION Range Default Description 
						

							3-28Programming
Ch apter 3 - Key Station Featu res , Operation , an d P rog rammin g
6. LCR Code This code is used to a ccess the LCR fea ture
Le ngth 1-4 1 The le ngth of the directory num be r ca n be
fr o m 1 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) 1 Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
A ccount Code The code is us ed for enteri ng a ccount code s
and this code is considered the first digi t of
the account code.
Le ngth 1-4 1 The le ngth of the directory num be r ca n be
fr o m 1 t o 4 d i g i t s .
Le ading 1 -4 ( 1-9 ) Nul l Any digit 1-9 c an be use d as the lead ing di git
as long a s it doe s not confli ct with e xisti ng
nu m b e r s.
7.
S U FFI X CODE
I CM Ring/Voice 1-# * Us ed to s witch be twe en voice and tone
ri n g i n g .
DND O verride 1-# 3 Used to override a station in DND.
C amp O n 1-# 4 Used to cam p on to a sta tion.
C all Back 1-# # Used to auto-call ba ck a busy sta tion.
C all Pickup 1-# 6 Us ed to pick up a ringing call in the sa me
pickup group.
I ntrus ion 1-# 8 Us ed to intrude on a sta tion be ing calle d. The
station m ust be programm ed to al low
intrude and the calle d stati on ne eds to have
intrus ion ena bled.
M sg Wa iting 1-# 9 Us ed to s et m es sage wa iting to the s tation
being ca lled.
ICM OHVA 1-# 0 N/A.
Table 3-8: System Application Programming Table
SYSTEM APPLICATION Range Default Description 
						

							Programming3-29
Chapt er 3 - Key Station Featu res , Opera tion , an d Programmin g
8.
ABBR. NO. ASSIGN.
(Speed Dial)Abbre viate d Numbe ring As signm ent ( use d
to program sp eed dial location a llocation)
I ndividua l Pe rs onal s pee d dial b ins
Show Sta - - Enter station number.
ºTo Incre ase 0-50 0 Use setting to all ow numb er of spe ed bins
per station. (Go to next setting to reduce
nu m b e r. )
ºTo Decrease 50-0 50 Use setting to all ow number of speed bins
per station. (Go to previous se tting to
in c r eas e n u m ber . )
Common Li st - - System speed bins
Show Tenant 1-6 - Enter tenant group.
ºTo Increase 0-1000 100 Use setting to all ow numb er of speed bins
per tena nt group. (Go to nex t se tting to
re d u c e n u m b er . )
ºTo Decrease 1000-0 100 Use setting to all ow number of speed bins
per tena nt group. (Go to prev ious setting to
re d u c e n u m b er . )
9.
CO L INE COPY The s ys tem a llows f or copy of the line
fe at u r es fr o m p o r t t o p or t .
Features copied: Tenant Group, Route, Day &
Ni ght CO S, Dialing M ode Trunk Type , Call
Abandon P rivate and A nsw ering P osition.
I ndividua l Copy - - Used to copy a single line setting to anothe r
line or line s, one line at a tim e.
Copy From - - Enter va lid trunk numbe r to b e used as
te m p l a t e .
Copy To - - Enter va lid trunk numbe r to b e change d.
Group Copy - - Copies se ttings f rom indiv idual line to trunk
group.
Copy From - - Enter vali d trunk group num ber to be used as
te m p l a t e .
Copy To - - Enter va lid trunk group numbe r to be
changed.
Table 3-8: System Application Programming Table
SYSTEM APPLICATION Range Default Description 
						

							3-30Programming
Ch apter 3 - Key Station Featu res , Operation , an d P rog rammin g
10.
STATION COPY The system allows fro copy of the station
fe at u r es fr o m p o r t t o p or t .
Th is opt ion D OES NOT copy F eat ure key s
o r D i al N u m be r S w ap pi n g.
I ndividua l Copy - - Used to copy a single stati on’s se tting to
another station or stations, one line a t a ti me.
Copy From - - Enter va lid sta tion numbe r to be use d as
te m p l a t e .
Copy To - - Enter va lid sta tion numbe r to be change d.
Group Copy - - Copies se ttings from an ind ividual station to
a sta tion p ickup group.
Copy From - - Enter va lid sta tion numbe r to be use d as
te m p l a t e .
Copy To - - Enter va lid sta tion pickup group numbe r to
be change d.
11.
F EATURE CO PY Used to cop y Feature key programming from
station to station. Must be sa me key se t t ype
(Ex ecutive /Enha nced).
CopyFrom - - Entervalidstationnumberwho’s ke ys w ill be
us e d a s t h e t em plat e.
C op y To - - Enter va lid sta tion numbe r w ho’sfeature
keysaretobechanged.
12.
NIT E S ERVICE STA Each te nant group may b e assi gned up to 5
exte nsions to b e used for ni te se rvi ce .
S how Te nant 1-6 - Enter va lid tena nt group num ber.
Member (1-5) Up to five members may be assigned to each
te nant group.
13.
SYSTEM TIME
Year 00-99 0
M onth 01-12 JA N Pre ss [chg] to scroll though month.
D a y 0 1- 3 1 01
Wee kday S UN -S AT S UN Pre ss [chg] to scroll though days.
Hour 00-23 01
Minute 01-59 00
Table 3-8: System Application Programming Table
SYSTEM APPLICATION Range Default Description