Home
>
Panasonic
>
Communications System
>
Panasonic Digital Business System 576 Technical Manual Section 400 Programming
Panasonic Digital Business System 576 Technical Manual Section 400 Programming
Have a look at the manual Panasonic Digital Business System 576 Technical Manual Section 400 Programming online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Section 400-Programming FF2: Trunk Programming (Analog CO)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-33
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes: (see “Day1 Delayed Ring Type/Destination” - pg. 2-31)
Related Programming: (see “Day1 Delayed Ring Type/Destination” - pg. 2-31)
Night Delayed Ring Type
(all CPCs) - Version 1.0 or higher
Set the analog CO trunk’s delayed-ringing type during Night mode.
NOTE:
Night Ring Type (pg. 2-30) must be either “DIL” or “Multiple
Incoming” to set Night Delayed Ringing (DID and DISA do not apply here).
FF2 0 BSSC 04 4 Hold (0-4) Hold
0=Disabled; no delayed ringing (default)BSSC: Analog (CO) Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-8
1=delay-ring to Extension
2=delay-ring to Hunt Group
3=delay-ring to SSD
4=delay-ring to Attendant Hunt Group
$
)1% %6
Night Delayed Ring Destination
(all CPCs) - Version 1.0 or higher
Assign a destination extension, Hunt Group, SSD code, or Attendant
Hunt Group, depending on the setting in the above address.
FF2 0 BSSC 04 5 Hold (0-9999) Hold
BSSC: Analog (CO) Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-8Destination Number:
(if “1=delay-ring to Extension”)
default: [no assignment]
(if “2=delay-ring to Hunt Group”)
(if “3=delay-ring to SSD”)
Ext.No., Virtual Ext.No., or Closed No.
(if “4=delay-ring to Attendant”)
Extension Hunt Group No. (1-72)
SSD Code No.
Attendant Hunt Group Pilot No.
$
) !
FF2: Trunk Programming (Analog CO) Section 400-Programming
Page 2-34
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
MOH Source for CO Trunks (pg. 1-96) FF1 0 12 (0001-0072) Hold (0-3) Hold
Notes:
Related Programming:
FF6 1: TRS Class Definitions (pg. 6-15)
Tenant Group Assignment
(all CPCs) - Version 1.0 or higher
Assign the trunk to a Tenant Group, which will apply when the trunk originates
an outbound call (such as DISA).
FF2 0 BSSC 05 Hold (0-72) Hold
Tenant Group No. --BSSC: Analog (CO) Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-8
with a CPC-96:
with a CPC-288:
with a CPC-576:
default: 0 [no assignment]
$
% 1!-6
Tenant Groups 01-12
Tenant Groups 01-36
Tenant Groups 01-72
TRS Class Assignment (Day)
(all CPCs) - Version 1.0 or higher
Assign a Toll Restriction Service (TRS) class to the trunk, applicable during
Day1 and Day2 modes when the trunk originates an outbound call (such as
DISA).
FF2 0 BSSC 06 0 Hold (1-50) Hold
TRS Class No. 1-50 for Day ModeBSSC: Analog (CO) Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-8
default: 1
$
0 % 5
Section 400-Programming FF2: Trunk Programming (Analog CO)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-35
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
FF6 1: TRS Class Definitions (pg. 6-15)
Notes:
This
Trunk COS
Assignment controls the ring tone for incoming calls on this trunk - CO ring tone,
intercom ring tone, or (for DIL trunks) a specific ring pattern. The Trunk COS also controls various
network settings. See
FF1 0 04: Trunk COS Definitions (pg. 1-75).
Related Programming:
Trunk COS: Incoming Ring Tone Source (pg. 1-75) FF1 0 04 (00-15) 01 Hold (0 or 1) Hold
Trunk COS: DID/DNIS Table (pg. 1-77) FF1 0 04 (00-15) 04 Hold (0 or 1) Hold
Trunk COS: Paging on DISA/Tie-Line Call (pg. 1-78) FF1 0 04 (00-15) 05 Hold (0 or 1) Hold
Trunk COS: DISA ID Verification (pg. 1-79) FF1 0 04 (00-15) 06 Hold (0 or 1) Hold
Ring Pattern (pg. 2-13) FF2 0 BSSC 01 12 Hold (0-12) Hold
Day1/Day2/Night Ring Type/Destination (pg. 2-28) FF2 0 BSSC 03 (0 thru 5) ...
TRS Class Assignment (Night)
(all CPCs) - Version 1.0 or higher
Assign a Toll Restriction Service (TRS) class to the trunk, applicable during
Night mode when the trunk originates an outbound call (such as DISA).
FF2 0 BSSC 06 1 Hold (1-50) Hold
TRS Class No. 1-50 for Night ModeBSSC: Analog (CO) Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-8
default: 1
$
)9 % 5
Trunk COS Assignment
(all CPCs) - Version 1.0 or higher
Assign a Trunk Class of Service (COS) number to the trunk.
FF2 0 BSSC 07 Hold (1-16) Hold
Trunk COS No. 1-16BSSC: Analog (CO) Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-8
default: 1
$
% %-4 #
FF2: Trunk Programming (Analog CO) Section 400-Programming
Page 2-36
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Based on this setting, you can assign automatic volume adjustments for different connection types to
this trunk (see FF1 8 02).
Related Programming:
Digital Pad Settings for Trunk Pad Class (pg. 1-178) FF1 8 02 (0001-0480) Hold (0-31) Hold
Trunk Digital Pad Class Assignment
(all CPCs) - Version 1.0 or higher
Assign a Digital Pad Class to the analog trunk.
FF2 0 BSSC 08 Hold (1-16) Hold
Trunk Digital Pad Class 1-16BSSC: Analog (CO) Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-8
default: 1
$
%-4 $/ 5
Section 400-Programming FF2: Trunk Programming (Analog E&M Tie)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-37
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
2.
FF2 0: Analog Trunks (E&M Tie)
NOTE:The same FF2 0 addresses are also used for analog CO trunks. However, their
settings are different. See page 2-7 for Analog Trunks (CO) settings.
Notes:
Press the BLK-DOWN soft key instead of the last HOLD in the above address, to scroll to the next
BSSC trunk position and assign it a trunk number (stay in same address).
Before removing a Trunk Card from a Free Slot, you must first clear the Trunk Numbers (if assigned)
from all of the Card’s BSSC ports in this address. See pg. 0-3 for more information.
The range of trunk numbers available for assignment depends on the CPC used:
with a CPC-96: Trunk Nos. 1-96
with a CPC-288: Trunk Nos. 1-288
with a CPC-576: Trunk Nos. 1-576
These ranges do not reflect the actual number of E&M trunk circuits available. For example, in a 576-
port system the range of available trunk numbers
is 576, but the actual number of circuits
available is
only 288 (each E&M trunk card has only 4 circuits, as opposed to 8 circuits on a regular analog trunk
card).
Related Programming:
Trunk Numbering (pg. 1-22) FF1 0 02 0001 Hold (0 or 1) Hold
Trunk Connection Type (CO/PBX) (pg. 2-47) FF2 0 BSSC 02 04 Hold (0 or 1) Hold
Trunk Number Assignment
(all CPCs) - Version 1.0 or higher
Assign trunk numbers for E&M tie trunks. (Maximum 288 E&M circuits are
available in a 6-cabinet system with a CPC-576 card.)
FF2 0 BSSC 00 Hold (0-576) Hold
Trunk Number assigned to trunk circuitBSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4(0 = no trunk)
default: [no assignment]
$
%-4 )-8
(or BLK-DOWN)
FF2: Trunk Programming (Analog E&M Tie) Section 400-Programming
Page 2-38
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
NOTE: Settings 0-3 apply to
Analog Trunks (CO).
See page
2-7 for more information.
Trunk Signal Type
(all CPCs) - Version 1.0 or higher
Set the E&M trunk’s signaling type.
FF2 0 BSSC 01 00 Hold (0-5) Hold
BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-44=E&M Immediate Start
5=E&M Wink Start (default for
E&M trunk card)
$
, %6
Not Used
(all CPCs) - Version 1.0 or higher
FF2 0 BSSC 01 01 Hold
FF2 0 BSSC 01 02 Hold
FF2 0 BSSC 01 03 Hold
FF2 0 BSSC 01 04 Hold
$
)! B
$
)! B
$
)! B
$
)! B
Section 400-Programming FF2: Trunk Programming (Analog E&M Tie)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-39
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
Trunk Signal Type (pg. 2-38) FF2 0 BSSC 01 00 Hold (0-5) Hold
Notes:
Set this to “1” (Enable) only if the other system does not send back an answer signal (typically, it does),
or if the trunk is used for paging calls.
Related Programming:
Auto Answer Timer (pg. 2-45) FF2 0 BSSC 01 18 Hold (0-3) Hold
Ring Detect Timer
(all CPCs) - Version 1.0 or higher
Set the amount of time allowed for the system to recognize an incoming call on
an E&M tie trunk set for
Immediate Start signaling (see
Trunk Signal Type).
FF2 0 BSSC 01 05 Hold (0 or 1) Hold
0=48 ms (default)BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
1=160 ms
$
*% %
Auto Answer for Outbound Calls
(all CPCs) - Version 1.0 or higher
Set whether the system will automatically assume that an outgoing call on this
trunk has been answered by the other end, without waiting for an answer signal.
FF2 0 BSSC 01 06 Hold (0 or 1) Hold
0=Disable Auto Answer; wait for answerBSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
signal from other end, before opening
voice path. (default)
1=Enable Auto Answer; open voice path
without waiting for answer signal.
$
/-! /)
FF2: Trunk Programming (Analog E&M Tie) Section 400-Programming
Page 2-40
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Because there are so many factors involved in choosing
Long Loop or
Short Loop (such as what kind
of wire/match is used for each connection; distance; Ohms/match; R, L, & C; etc.), this setting should be
tested on the trunk, or changed only if problems occur.
Related Programming:
Notes:
Related Programming:
Balance Control
(all CPCs) - Version 1.0 or higher
For impedance matching in balanced networks. Controls sidetone level on
the trunk, based on the distance between the phone system and the other end.
FF2 0 BSSC 01 07 Hold (0 or 1) Hold
0=Long Loop (default)
1=Short Loop BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
$
%
7, !!,
Pad Control
(all CPCs) - Version 1.0 or higher
For balanced networks. Controls voice level on the E&M tie trunk, depending on
the distance between the phone system and the other end (CO or another system).
FF2 0 BSSC 01 08 Hold (0 or 1) Hold
0=Far (default)BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
1=Near
$
$/ !!,
Section 400-Programming FF2: Trunk Programming (Analog E&M Tie)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-41
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
Not Used
(all CPCs) - Version 1.0 or higher
FF2 0 BSSC 01 09 Hold
FF2 0 BSSC 01 10 Hold
$
& )! B
$
)! B
Ring Frequency
(all CPCs) - Version 1.0 or higher
Set the ring frequency for the E&M tie trunk. Affects ringing pitch on
digital phones only.
FF2 0 BSSC 01 11 Hold (1-6) Hold
1=400/562 Hz (default)BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
2=1000/1340 Hz
3=400 Hz
4=800/1040 Hz
5=1040/1320 Hz
6=660/1320 Hz
$
F-
FF2: Trunk Programming (Analog E&M Tie) Section 400-Programming
Page 2-42
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
Ring Pattern
(all CPCs) - Version 1.0 or higher
(This setting does not apply to E&M tie-trunks.)
FF2 0 BSSC 01 12 Hold (0-12) Hold
Setting Values for U.K.Setting Values for U.S. and Hong Kong
0Synchronize with CO0Synchronize with CO
11on/2off (default) (in seconds)11on/3off (in seconds) (default)
22on/1off22on/2off
31on/1off33on/1off
4.5on/.5off41on/1off
5.25on/2.75off5.5on/.5off
6.25on/.25off/.25on/2.25off6.5on/3.5off
7.25on/.25off/.25on/.25off/.25on/1.75off7.5on/.5off/.5on/2.5off
8.75on/.25off/.75on/1.25off8.25on/.25off/.25on/3.25off
91on/.25off/.25on/1.5off91on/.25off/.25on/2.5off
101on/.25off/.25on/.25off/.25on/1off101on/.25off/.25on/.25off/.25on/2off
111.375on/.125off/.125on/.125off/.125on/.125off111.375on/.125off/.125on/.125off/.125on/.125off
12Continuous tone12Continuous tone
BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
$
, $%)