Home > Panasonic > Communications System > Panasonic Digital Business System 576 Technical Manual Section 400 Programming

Panasonic Digital Business System 576 Technical Manual Section 400 Programming

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Panasonic Digital Business System 576 Technical Manual Section 400 Programming online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 664
    Add page 61 to Favourites
    image text
    Enable zoom 
    							Section 400-Programming 0: System Configuration
576-13-400 DBS 576 (USA) issued 05/20/98
     l     Page 0-7
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Table 0-1.   Free Slot/Option Slot card types   (01 and 02 addresses)     
Setting Card Type Value Notes
1
Loop Start Trunk Card/8-port
2
Loop Start/Ground Start Trunk Card/8-port
3
DID Card
4
E&M Card/4 ports
5:  Not Used
6
T1 Card/8-channel use
7
T1 Card/16-channel useUse slot 1, 5, or 9.
Next slot can’t be used.
8
T1 Card/24-channel useUse slot 1, 5, or 9.
Next 2 slots can’t be used.
9:  Not Used
10

ISDN BRI Trunk Card2B+D/4
11
ISDN PRI Trunk Card/8-channel use8B+D/1
12
ISDN PRI Trunk Card/16-channel use16B+D/1
Use slot 1, 5, or 9.
Next slot can’t be used.
13
ISDN PRI Trunk Card/23- or 24-channel use23B+D/1
Use slot 1, 5, or 9.
Next 2 slots can’t be used.
14-29:  Not Used
30

Digital Extension Card/8-port
31
Analog Extension Card/8-port
32-34:  Not Used
35
 
BRI Card/S-point2B+D/4
36
ISDN PRI Extension Card/S-point/8-channel use8B+D/1
37
ISDN PRI Extension Card/S-point/23- or 24-channel 
use23B+D/1
Use slot 1, 5, or 9.
Next 2 slots can’t be used.
38-49:  Not Used
50
!
DTMF Receiver CardInstall in OP slot 13 or 14.
51-59:  Not Used
60

#$Built-In Voice Mail  (VSSC and one VPU/4)Slot 10=VPU/4
Slot 11=VSSC
Provides 4 voice ports.
61:  Not Used
62

#$Built-In Voice Mail  (VSSC and one VPU/8)Slot 10=VPU/8
Slot 11=VSSC
Provides 8 voice ports.
63:  Not Used
64

#$#$Built-In Voice Mail  (VSSC and two VPU/4s)Slot 9=VPU/4
Slot 10=VPU/4
Slot 11=VSSC
Provides 8 voice ports.
    Add page 62 to Favourites
    image text
    Enable zoom 
    							0: System Configuration Section 400-Programming
Page 0-8
     l     DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
65
#$#$Built-In Voice Mail  (VSSC, one VPU/8, one VPU/4)Slot 9=VPU/8
Slot 10=VPU/4
Slot 11=VSSC
Provides 12 voice ports.
66:  Not Used
67

#$#$Built-In Voice Mail  (VSSC and two VPU/8s)Slot 9=VPU/8
Slot 10=VPU/8
Slot 11=VSSC
Provides 16 voice ports.
68-69:  Not Used
70
 
#$ACD 4-channel #1Provides 4 voice ports.
71-79:  Not Used
80
$
API with AEC for 3rd-Party Voice Mail (2-port)ports 7-8: Voice Mail
ports 1-6: available for use
81$
API with AEC for 3rd-Party Voice Mail (4-port)ports 5-8: Voice Mail
ports 1-4: available for use
82$
API with AEC for 3rd-Party Voice Mail (6-port)ports 3-8: Voice Mail
ports 1-2: available for use
83$
API with AEC for 3rd-Party Voice Mail (8-port)ports 1-8: Voice Mail
84$
API with DEC for 3rd-Party Voice Mail (2-port)ports 7-8: Voice Mail
ports 1-6: available for use
85$
API with DEC for 3rd-Party Voice Mail (4-port)ports 5-8: Voice Mail
ports 1-4: available for use
86$
API with DEC for 3rd-Party Voice Mail (6-port)ports 3-8: Voice Mail
ports 1-2: available for use
87$
API with DEC for 3rd-Party Voice Mail (8-port)ports 1-8: Voice Mail
88-99:  Not Used
Setting Card Type Value Notes
    Add page 63 to Favourites
    image text
    Enable zoom 
    							576-13-400 DBS 576 (USA) issued 05/20/98     l     Page 1-1
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
1.  System Programming  (FF1)
Use the FF1 programming addresses in this chapter to set system-wide 
parameters for the DBS 576:
FF1  0: System Common
FF1  0  01 General 1
FF1  0  02 General 2
FF1  0  03 Extension COS Definitions
FF1  0  04 Trunk COS Definitions
FF1  0  05 Serial Ports
FF1  0  06 Serial Port Output Data
FF1  0  07 and 08 PBX Parameters
FF1  0  09 SMDR Output Format
FF1  0  10 and 11 Call Restriction Between COS
FF1  0  12, 13, and 14 MOH Source
FF1  0  15, 16, and 17 SSD Blocks
FF1  0  18 Sychronized Clock
FF1  0  19 TRS Class for Forced Account Codes
FF1  0  20 Ext.No. Display for Closed-Number Calls
FF1  0  21 Ring Alarm for Unanswered Calls
FF1  0  22 Dealer Programming ID Code
FF1  0  23 and 24 Voice Mail Codes
FF1  0  25 Caller ID Add Digits
FF1  0  26 DISA ID Codes
FF1  1: System Timers
FF1  1  01 Trunk Timer 1
FF1  1  02 Trunk Timer 2
FF1  1  03 Extension Timer 1
FF1  1  04 Extension Timer 2
FF1  2: Dial Plan
FF1  3: MCO Access
FF1  4: DID/DNIS Tables
FF1  5: Not Used
FF1  6: Not Used
FF1  7: Not Used
FF1  8: Digital Pad Settings
This chapter covers the following FF1 addresses:    
       
FF Key Address Topic Default Page
FF1 0: System Common1-9
FF1 0 01: General 11-9
FF1 0 01 0001 Hold (0 or 1) Hold Splash Tone: Voice Calls 1 (Enabled) 1-9
FF1 0 01 0002 Hold (0 or 1) Hold Splash Tone: Internal Paging 1 (Enabled) 1-9
FF1 0 01 0003 Hold (0 or 1) Hold Splash Tone: Busy Override (Start) 1 (Enabled) 1-10
FF1 0 01 0004 Hold (0 or 1) Hold Splash Tone: Busy Override (Continuous) 0 (Disabled) 1-10
FF1 0 01 0005 Hold (0 or 1) Hold Splash Tone: 3-Party Conference 0 (Disabled) 1-11
FF1 0 01 0006 Hold (0 or 1) Hold Exclusive Hold (CO Key) 1 (Enabled) 1-11
FF1 0 01 0007 Hold (0 or 1) Hold Virtual Key LED: Answer Control #1 0 (Free-up key) 1-12
    Add page 64 to Favourites
    image text
    Enable zoom 
    							FF1: System Programming Section 400-Programming
Page 1-2
     l     DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1 0 01 0008 Hold (0 or 1) Hold Virtual Key LED: Answer Control #2 1 (Free-up key) 1-13
FF1 0 01 0009 Hold (0 or 1) Hold Floating Hold on Trunk Key 0 (Disabled) 1-14
FF1 0 01 0010 Hold (0 or 1) Hold Floating Hold on Virtual Port Key 0 (Disabled) 1-14
FF1 0 01 0011 Hold (0 or 1) Hold Hot Line/MCO Preference for “ON/OFF” Key 0 (Disabled) 1-15
FF1 0 01 0012 Hold (0 or 1) Hold Programming Mode Entry 1 (Allowed) 1-15
FF1 0 01 0013 Hold (0 or 1) Hold Built-In VM: Voice Mail Access Key 1 (Enabled) 1-16
FF1 0 01 0014 Hold (0 or 1) Hold Built-In VM: Mailbox Key 1 (Enabled) 1-16
FF1 0 01 0015 Hold (0 or 1) Hold Built-In VM: Message Retrieve Key 1 (Enabled) 1-17
FF1 0 01 0016 Hold (0 or 1) Hold Off-Hook Monitor 1 (Enabled) 1-17
FF1 0 01 0017 Hold (0 or 1) Hold Handset Mute 1 (Enabled) 1-18
FF1 0 01 0018 Hold (0 or 1) Hold Hookflash on Rotary SLTs 0 (hookflash) 1-18
FF1 0 01 0019 Hold (0 or 1) Hold ISDN Outgoing Control 0 (Disabled) 1-19
FF1 0 01 0020 Hold (0 or 1) Hold Automatic BLF on DSS and EM/24 Units 0 (Disabled) 1-19
FF1 0 01 0021 Hold (0 or 1) Hold Caller ID Log Outgoing Control 0 (Disabled) 1-20
FF1 0 01 0022 Hold (0 or 1) Hold Caller ID Log Private/Out-of-Area Control 1 (Enabled) 1-20
FF1 0 01 0023 Hold (0 or 1) Hold Time Display Mode 1 (12-hour) 1-21
FF1 0 02: General 21-22
FF1 0 02 0001 Hold (0 or 1) Hold Trunk Numbering 0 (2-digit) 1-22
FF1 0 02 0002 Hold (0 or 1) Hold SSD Code Numbering 1 (3-digit) 1-22
FF1 0 02 0003 Hold (0 or 1) Hold SSD Assignment to Groups 0 (Disabled) 1-23
FF1 0 02 0004 Hold (0 or 1) Hold Trunk Access in Speed Dialing 1 (Enabled) 1-23
FF1 0 02 0005 Hold (0 or 1) Hold Intercom Voice Call Pickup 0 (Disabled) 1-24
FF1 0 02 0006 Hold (0 or 1) Hold BLF Call Pickup 1 (Enabled) 1-24
FF1 0 02 0007 Hold (0 or 1) Hold Day/Night Mode Assignment 0 (System-wide) 1-25
FF1 0 02 0008 Hold (0 or 1) Hold Step Calling: Intercom Calls 0 (Disabled) 1-26
FF1 0 02 0009 Hold (0 or 1) Hold Step Calling: DISA/Tie-Line 0 (Disabled) 1-26
FF1 0 02 0010 Hold (0 or 1) Hold ARS/LCR Setting 0 (Disabled) 1-27
FF1 0 02 0011 Hold (0 or 1) Hold Advanced Routing for MCO Access 0 (Disabled) 1-27
FF1 0 02 0012 Hold (0 or 1) Hold Page Override 1 (Enabled) 1-28
FF1 0 02 0013 Hold (0 or 1) Hold Paging Answer on Tie-Line 0 (no ansr.signl) 1-29
FF1 0 02 0014 Hold (0 or 1) Hold Howler Tone 0 (Disabled) 1-29
FF1 0 02 0015 Hold (0 or 1) Hold DISA Invalid Number 0 (multi-incomg.) 1-30
FF1 0 02 0016 Hold (0 or 1) Hold DISA Interdigit Timeout 0 (multi-incomg.) 1-30
FF1 0 02 0017 Hold (0 or 1) Hold DISA No-Answer Timeout 0 (multi-incomg.) 1-31
FF1 0 02 0018 Hold (0 or 1) Hold DID to Busy Extension (Day1) 0 (busy signal) 1-31
FF1 0 02 0019 Hold (0 or 1) Hold DID to Busy Extension (Day2) 0 (busy signal) 1-32
FF1 0 02 0020 Hold (0 or 1) Hold DID to Busy Extension (Night) 0 (busy signal) 1-32
FF1 0 02 0021 Hold (0 or 1) Hold DID to Incorrect Number (Day1) 0 (busy signal) 1-33
FF1 0 02 0022 Hold (0 or 1) Hold DID to Incorrect Number (Day2) 0 (busy signal) 1-33
FF1 0 02 0023 Hold (0 or 1) Hold DID to Incorrect Number (Night) 0 (busy signal) 1-34
FF1 0 03:  Extension COS Definitions 1-35
FF1 0 03 (00-15) 01 Hold (0 or 1) Hold Extension COS: Intercom Calling Type 1 (Voice) 1-36
FF1 0 03 (00-15) 02 Hold (0 or 1) Hold Extension COS: Onhook Transfer at 
Ringback0 (Allowed) 1-37
FF1 0 03 (00-15) 03 Hold (0 or 1) Hold3 Extension COS: Onhook Transfer at Talk 0 (Allowed) 1-38
FF1 0 03 (00-15) 04 Hold (0 or 1) Hold Extension COS: Onhook Transfer at Camp-
On0 (Allowed) 1-39
    Add page 65 to Favourites
    image text
    Enable zoom 
    							Section 400-Programming FF1: System Programming
576-13-400 DBS 576 (USA) issued 05/20/98
     l     Page 1-3
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1 0 03 (00-15) 05 Hold (0 or 1) Hold Extension COS: Exclusive Hold for Non-
Appearing CO0 (System Hold) 1-40
FF1 0 03 (00-15) 06 Hold (0 or 1) Hold Extension COS: Exclusive Hold on SLTs 0 (System Hold) 1-41
FF1 0 03 (00-15) 07 Hold (0 or 1) Hold Extension COS: Brokers Hold on SLTs 1 (Broker’s Hold) 1-42
FF1 0 03 (00-15) 08 Hold (0 or 1) Hold Extension COS: Hookflash Control on SLTs 0 (Allowed) 1-43
FF1 0 03 (00-15) 09 Hold (0 or 1) Hold Extension COS: SSD Assignment 1 (Not Allowed) 1-43
FF1 0 03 (00-15) 10 Hold (0 or 1) Hold Extension COS: SSD Assignment to MCO 
Tenant Groups1 (Not Allowed) 1-44
FF1 0 03 (00-15) 11 Hold (0 or 1) Hold Extension COS: SSD Dialing 0 (Allowed) 1-45
FF1 0 03 (00-15) 12 Hold (0 or 1) Hold Extension COS: Intercom Redialing 1 (Not Allowed) 1-46
FF1 0 03 (00-15) 13 Hold (0 or 1) Hold Extension COS: Direct Trunk Access 0 (Allowed) 1-46
FF1 0 03 (00-15) 14 Hold (0 or 1) Hold Extension COS: MCO Incoming Call Answer 0 (Allowed) 1-47
FF1 0 03 (00-15) 15 Hold (0 or 1) Hold Extension COS: Paging 0 (Allowed) 1-48
FF1 0 03 (00-15) 16 Hold (0 or 1) Hold Extension COS: Auto Repeat Dial 0 (Allowed) 1-48
FF1 0 03 (00-15) 17 Hold (0 or 1) Hold Extension COS: DND Set/Clear 0 (Allowed) 1-49
FF1 0 03 (00-15) 18 Hold (0 or 1) Hold Extension COS: DND Set/Clear (Other) 1 (Not Allowed) 1-50
FF1 0 03 (00-15) 19 Hold (0 or 1) Hold Extension COS: Call Forward/All Calls 0 (Allowed) 1-50
FF1 0 03 (00-15) 20 Hold (0 or 1) Hold Extension COS: Call Forward/No Answer 0 (Allowed) 1-51
FF1 0 03 (00-15) 21 Hold (0 or 1) Hold Extension COS: Call Forward/Busy 0 (Allowed) 1-52
FF1 0 03 (00-15) 22 Hold (0 or 1) Hold Extension COS: Call Forward/Other 1 (Not Allowed) 1-52
FF1 0 03 (00-15) 23 Hold (0 or 1) Hold Extension COS: User Log-In 1 (Not Allowed) 1-53
FF1 0 03 (00-15) 24 Hold (0 or 1) Hold Extension COS: Priority Message Waiting 
Send (VM)1 (Not Allowed) 1-54
FF1 0 03 (00-15) 25 Hold (0 or 1) Hold Extension COS: Message Waiting Send 0 (Allowed) 1-55
FF1 0 03 (00-15) 26 Hold (0 or 1) Hold Extension COS: System Mode Switch 1 (Not Allowed) 1-55
FF1 0 03 (00-15) 27 Hold (0 or 1) Hold Extension COS: Busy Override Send 0 (Allowed) 1-56
FF1 0 03 (00-15) 28 Hold (0 or 1) Hold Extension COS: Manual Camp-On Send 0 (Allowed) 1-57
FF1 0 03 (00-15) 29 Hold (0 or 1) Hold Extension COS: Manual Camp-On Receive 0 (Allowed) 1-58
FF1 0 03 (00-15) 30 Hold (0 or 1) Hold Extension COS: Callback Request Send 0 (Allowed) 1-58
FF1 0 03 (00-15) 31 Hold (0 or 1) Hold Extension COS: Callback Request Receive 0 (Allowed) 1-59
FF1 0 03 (00-15) 32 Hold (0 or 1) Hold Extension COS: Trunk Queuing 0 (Allowed) 1-60
FF1 0 03 (00-15) 33 Hold (0 or 1) Hold Extension COS: Manual DND Override 
Send1 (Not Allowed) 1-61
FF1 0 03 (00-15) 34 Hold (0 or 1) Hold Extension COS: Forced DND Override 1 (Not Allowed) 1-61
FF1 0 03 (00-15) 35 Hold (0 or 1) Hold Extension COS: 8-Party Conference 1 (Not Allowed) 1-62
FF1 0 03 (00-15) 36 Hold (0 or 1) Hold Extension COS: Voice Call Send 0 (Allowed) 1-63
FF1 0 03 (00-15) 37 Hold (0 or 1) Hold Extension COS: Voice Call Receive 0 (Allowed) 1-64
FF1 0 03 (00-15) 38 Hold (0 or 1) Hold Extension COS: Dial Tone Stop 1 (Receive 
internl dial tone)1-64
FF1 0 03 (00-15) 39 Hold (0 or 1) Hold Extension COS: Dial Tone Pre-Pause Check 1 (Check/send 
re-order tone)1-65
FF1 0 03 (00-15) 40 Hold (0 or 1) Hold Extension COS: Long Talk Alarm 0 (Disabled) 1-66
FF1 0 03 (00-15) 41 Hold (0 or 1) Hold Extension COS: Recall Timer Apply 0 (Ext.Recall) 1-67
FF1 0 03 (00-15) 42 Hold (0 or 1) Hold Extension COS: Forced ARS 0 (Disabled) 1-68
FF1 0 03 (00-15) 43 Hold (0 or 1) Hold Extension COS: API Event Reporting 1 (Enabled) 1-69
FF1 0 03 (00-15) 44 Hold (0 or 1) Hold Extension COS: Call Forward/Outside 0 (Allowed) 1-69
FF1 0 03 (00-15) 45 Hold (0 or 1) Hold Extension COS: Onhook Trunk-to-Trunk 
Transfer1 (Not Allowed) 1-70
FF1 0 03 (00-15) 46 Hold (0 or 1) Hold Extension COS: Station Call Park Answer 0 (Allowed) 1-71
FF1 0 03 (00-15) 47 Hold (0 or 1) Hold Extension COS: Station Call Park Transfer 0 (Allowed) 1-72
    Add page 66 to Favourites
    image text
    Enable zoom 
    							FF1: System Programming Section 400-Programming
Page 1-4
     l     DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1 0 03 (00-15) 48 Hold (0 or 1) Hold Extension COS: OHVA 0 (Allowed) 1-72
FF1 0 03 (00-15) 49 Hold (0 or 1) Hold Extension COS: OHVA Answer 0 (Allowed) 1-73
FF1 0 03 (00-15) 50 Hold (0 or 1) Hold Extension COS: Call-Waiting Answer at 
HOLD1 (Not Allowed) 1-74
FF1 0 04: Trunk COS Definitions  1-75
FF1 0 04 (00-15) 01 Hold (0 or 1) Hold Trunk COS: Incoming Ring Tone Source 0 (use trunk’s 
Ring Pattern)1-75
FF1 0 04 (00-15) 02 Hold (0 or 1) Hold Trunk COS: Dial Tone to Tie-Line 1 (Enabled) 1-76
FF1 0 04 (00-15) 03 Hold (0 or 1) Hold Trunk COS: Forced Recovery at Fast-Busy 0 (Enabled) 1-77
FF1 0 04 (00-15) 04 Hold (0 or 1) Hold Trunk COS: DID/DNIS Table 0 (“A” side) 1-77
FF1 0 04 (00-15) 05 Hold (0 or 1) Hold Trunk COS: Paging on DISA/Tie-Line Call 0 (Not Allowed) 1-78
FF1 0 04 (00-15) 06 Hold (0 or 1) Hold Trunk COS: DISA ID Verification 0 (Verify) 1-79
FF1 0 05: Serial Ports1-80
FF1 0 05 0001 Hold (0-7) Hold Serial Port 1: Data Format 5  (8bits/NoPar./
1stop)1-80
FF1 0 05 0002 Hold (0-5) Hold Serial Port 1: Baud Rate 5  (9600 bps) 1-81
FF1 0 05 0003 Hold (0-2) Hold Serial Port 1: Protocol 0 (No order) 1-81
FF1 0 05 0004 Hold (0 or 1) Hold Serial Port 1: Echo Control (future use) 0 (Off) 1-82
FF1 0 05 0005 Hold (1-255) Hold Serial Port 1: Maximum Input Digits (future 
use)80 digits 1-82
FF1 0 05 0017 Hold (0-7) Hold RAI Serial Port: Data Format 5  (8Bits/NoPar./
1stop)1-83
FF1 0 05 0018 Hold (0-5) Hold RAI Serial Port: Baud Rate 5  (9600 bps) 1-83
FF1 0 05 0019 Hold (0-2) Hold RAI Serial Port: Protocol 0 (No order) 1-84
FF1 0 05 0020 Hold (0 or 1) Hold RAI Serial Port: Echo Control 0 (Off) 1-84
FF1 0 05 0021 Hold (1-255) Hold RAI Serial Port: Maximum Input Digits 1 digit 1-85
FF1 0 05 0033 Hold (0-7) Hold Serial Port 2: Data Format 5  (8bits/NoPar./
1stop)1-85
FF1 0 05 0034 Hold (0-5) Hold Serial Port 2: Baud Rate 5 (9600 bps) 1-86
FF1 0 05 0035 Hold (0-2) Hold Serial Port 2: Protocol 0 (No order) 1-86
FF1 0 05 0036 Hold (0 or 1) Hold Serial Port 2: Echo Control 0 (Off) 1-87
FF1 0 05 0037 Hold (1-255) Hold Serial Port 2: Maximum Input Digits 80 digits 1-87
FF1 0 06: Serial Port Output Data 1-88
FF1 0 06 0001 Hold (0-2) Hold SMDR Data to Serial Port 1 (Port 1) 1-88
FF1 0 06 0002 Hold (0-2) Hold Fault Alarm Data to Serial Port 0 (None) 1-88
FF1 0 06 0003 Hold (0-2) Hold Programmed Data to Serial Port 2 (Port 2) 1-89
FF1 0 06 0004 Hold Not Used -- 1-89
FF1 0 06 0005 Hold (0-2) Hold Bus Monitor Data to Serial Port 2 (Port 2) 1-90
FF1 0 07 and 08: PBX Parameters 1-91
FF1 0 07 (0001-0012) Hold (0-16) Hold Auto Pause Position Behind PBX 1 (for ”9”)
0 (for all others)1-91
FF1 0 08 (0001-0006) Hold FLASH  (0-
9999) HoldPBX Trunk Access Codes Code 1:  9
Codes 2-6: none1-92
FF1 0 09: SMDR Output Format 1-93
FF1 0 09 0001 Hold (0-2) Hold SMDR Output Format 1 (Format #1) 1-93
FF1 0 10 and 11: Call Restriction Between COS 1-94
FF1 0 10 (00-15) (01-16) Hold (0 or 1) Hold Call Restriction Between Extension COS 0 (Allowed) 1-94
FF1 0 11 (00-15) (01-16) Hold (0 or 1) Hold Call Restriction Between Trunk COS 0 (Allowed) 1-95
    Add page 67 to Favourites
    image text
    Enable zoom 
    							Section 400-Programming FF1: System Programming
576-13-400 DBS 576 (USA) issued 05/20/98
     l     Page 1-5
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1 0 12, 13, and 14: MOH Source 1-96
FF1 0 12 (0001-0072) Hold (0-3) Hold MOH Source for CO Trunks 0 (Internal single 
tone)1-96
FF1 0 13 (0001-0072) Hold (0-3) Hold MOH Source for Tie-Lines 0 (Internal single 
tone)1-97
FF1 0 14 (0001-0072) Hold (0-3) Hold MOH Source for Intercom Calls 0 (Internal single 
tone)1-98
FF1 0 15, 16, and 17: SSD Blocks 1-99
FF1 0 15 (0001-0072) Hold (0-72) Hold SSD Block Assignment to MCO Tenant 
Groups1 (SSD Block 1) 1-99
FF1 0 16 0001 Hold (0-800) Hold SSD Common Block for MCO Tenant 
Groups0 (none) 1-100
FF1 0 17 (0001-0144) Hold (0-799 or 0-800) 
HoldSSD Block Assignment See pg. 1-101 1-100
FF1 0 18: Synchronized Clock 1-103
FF1 018 (0001-0003) Hold (BSS/C) Hold Synchronized Clock  -- 1-103
FF1 0 19: TRS Class for Forced Account Codes 1-104
FF1 0 19 0001 Hold (1-50) Hold TRS Class for Forced Account Codes 1 (TRS Class 1) 1-104
FF1 0 20: Ext.No. Display for Closed-Number Calls 1-104
FF1 0 20 0001 Hold (0-4) Hold Ext.No. Display for Closed-Number Calls 0 (no digits) 1-105
FF1 0 21: Ring Alarm for Unanswered Calls 1-105
FF1 0 21 0001 Hold (0-6) Hold Ring Alarm Frequency 1 (400/562Hz) 1-106
FF1 0 21 0002 Hold (0-12) Hold Ring Alarm Pattern 5 (.5on/.5off) 1-107
FF1 0 22: Dealer Programming ID Code 1-108
FF1 0 22 0001 Hold (0000-9999) Hold Dealer Programming ID Code 9999  1-108
FF1 0 23 and 24: Voice Mail Codes 1-109
FF1 0 23 0001 Hold (0000-9999) Hold VM Answer Supervision Code -- (none) 1-109
FF1 0 24 0001 Hold (up to 8 char.) Hold VM Transfer Code #1: Prefix -- (none) 1-109
FF1 0 24 0002 Hold (up to 8 char.) Hold VM Transfer Code #1: Suffix -- (none) 1-110
FF1 0 24 0003 Hold (up to 8 char.) Hold VM Transfer Code #2: Prefix -- (none) 1-110
FF1 0 24 0004 Hold (up to 8 char.) Hold VM Transfer Code #2: Suffix -- (none) 1-111
FF1 0 25: Caller ID Add Digits 1-112
FF1 0 25 0001 Hold (up to 4 char.) Hold Caller ID Log Outgoing Add Digits -- (none) 1-112
FF1 0 26: DISA ID Codes1-113
FF1 0 26 0001 Hold (0-10) Hold DISA ID Code Numbering 0 (no code) 1-113
FF1 0 26 (0002-0033) Hold (up to 10 digits 
or 1-50) HoldDISA ID Codes and TRS Assignments -- (no code)
0 (no TRS Class)1-114
FF1 1: System Timers1-115
FF1 1 01: Trunk Timer 11-115
FF1 1 01 0001 Hold (1-255) Hold Flash Timer 1 for Trunk Line 50 (800ms) 1-115
FF1 1 01 0002 Hold (1-255) Hold Flash Timer 2 for Trunk Line 5 (80ms) 1-117
FF1 1 01 0003 Hold (1-255) Hold Flash Timer for Auto-Repeat Dial 124 (1984ms) 1-117
FF1 1 01 0004 Hold (1-255) Hold Pause Timer 3 (seconds) 1-117
FF1 1 01 0005 Hold (1-255) Hold Call Duration Timer (analog CO) 10 (seconds) 1-118
FF1 1 01 0006 Hold (1-255) Hold Call Duration Timer (Tie-Lines) 10 (seconds) 1-118
FF1 1 01 0007 Hold (1-255) Hold Outpulse Delay Timer (analog CO) 3 (seconds) 1-119
    Add page 68 to Favourites
    image text
    Enable zoom 
    							FF1: System Programming Section 400-Programming
Page 1-6
     l     DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1 1 01 0008 Hold (1-255) Hold Outpulse Delay Timer (analog Tie-Lines/ 
(Immediate-Start)1 (second) 1-119
FF1 1 01 0009 Hold (1-255) Hold Pre-Pause Timer (ISDN CO) 30 (seconds) 1-120
FF1 1 01 0010 Hold (1-255) Hold Interdigit Timer (ARS and ISDN CO) 10 (seconds) 1-120
FF1 1 01 0011 Hold
FF1 1 01 0012 HoldNot Used -- 1-121
FF1 1 01 0013 Hold (1-255) Hold Wink Wait Timer (analog Tie-Lines) 5 (seconds) 1-121
FF1 1 01 0014 Hold (1-255) Hold Start Timer for CO Busy Tone Detect (Auto-
Repeat Dial)5 (seconds) 1-122
FF1 1 01 0015 Hold (1-255) Hold CO Busy Tone Detect Timer (Auto-Repeat 
Dial)30 (seconds) 1-123
FF1 1 01 0016 Hold (1-255) Hold DTMF ON: Pattern #1 16 (80ms) 1-123
FF1 1 01 0017 Hold (1-255) Hold DTMF OFF: Pattern #1 9 (45ms) 1-124
FF1 1 01 0018 Hold (1-255) Hold DTMF ON/OFF: Pattern #2 1 (125ms on/
125ms off)1-125
FF1 1 01 0019 Hold (1-255) Hold DTMF ON/OFF: Pattern #3 2 (250ms on/
250ms off)1-126
FF1 1 02: Trunk Timer 21-127
FF1 1 02 0001 Hold (0-255) Hold DISA No-Answer Timer #1 30 (seconds) 1-127
FF1 1 02 0002 Hold (0-255) Hold Multiple Incoming No-Answer Timer #2 16 (seconds) 1-128
FF1 1 02 0003 Hold (0-255) Hold CO Delayed Ring Timer (Day1) 0 (5 seconds) 1-129
FF1 1 02 0004 Hold (0-255) Hold CO Delayed Ring Timer (Day2) 0 (5 seconds) 1-129
FF1 1 02 0005 Hold (0-255) Hold CO Delayed Ring Timer (Night) 0 (5 seconds) 1-130
FF1 1 02 0006 Hold (0-255) Hold CO Delayed Ring Timer (Busy) 120 (seconds) 1-131
FF1 1 02 0007 Hold (0-255) Hold Slide Ring/Alarm Ring Timer (Day1) 20 (seconds) 1-132
FF1 1 02 0008 Hold (0-255) Hold Slide Ring/Alarm Ring Timer (Day2) 20 (seconds) 1-133
FF1 1 02 0009 Hold (0-255) Hold Slide Ring/Alarm Ring Timer (Night) 20 (seconds) 1-133
FF1 1 02 0010 Hold (0-255) Hold Long Talk Alarm #1 Timer 180 (seconds) 1-134
FF1 1 02 0011 Hold (0-255) Hold Long Talk Alarm #2 Timer 60 (seconds) 1-135
FF1 1 02 0012 Hold (0-255) Hold Paging Timer (Tie-Lines) 30 (seconds) 1-135
FF1 1 02 0013 Hold (0-255) Hold Trunk-to-Trunk Connection Timer 60 (minutes) 1-136
FF1 1 02 0014 Hold (0-255) Hold Queuing Timer (ARS) 15 (seconds) 1-136
FF1 1 02 0015 Hold (0-255) Hold DID Delayed Ring Timer 20 (seconds) 1-137
FF1 1 03: Extension Timer 1 1-138
FF1 1 03 0001 Hold (0-255) Hold Call Forward/DND Confirmation Tone Timer 3 (seconds) 1-138
FF1 1 03 0002 Hold (0-255) Hold Message-Waiting Tone Timer 3 (seconds) 1-138
FF1 1 03 0003 Hold (0-255) Hold Pre-Pause Timer at Internal Dial Tone (DP 
SLTs)30 (seconds) 1-139
FF1 1 03 0004 Hold (0-255) Hold Pre-Pause Timer at Internal Dial Tone 
(DTMF SLTs)15 (seconds) 1-140
FF1 1 03 0005 Hold (0-255) Hold Pre-Pause Timer at Internal Dial Tone 
(Digital Keyphones)0 (wait indefintly) 1-140
FF1 1 03 0006 Hold (0-255) Hold Interdigit Timer (DP SLTs) 15 (seconds) 1-141
FF1 1 03 0007 Hold (0-255) Hold Interdigit Timer (DTMF SLTs) 15 (seconds) 1-142
FF1 1 03 0008 Hold (0-255) Hold Interdigit Timer (Digital Keyphones) 0 (wait indefintly) 1-142
FF1 1 03 0009 Hold (0-255) Hold DTMF Receiver Queuing Timer 6 (seconds) 1-143
FF1 1 03 0010 Hold
FF1 1 03 0011 HoldNot Used -- 1-143
FF1 1 03 0012 Hold (0-255) Hold SLT Off Hook Signal Interval 10 (seconds) 1-144
FF1 1 03 0013 Hold (0-255) Hold BLF Delayed Ring Timer 16 (seconds) 1-144
    Add page 69 to Favourites
    image text
    Enable zoom 
    							Section 400-Programming FF1: System Programming
576-13-400 DBS 576 (USA) issued 05/20/98
     l     Page 1-7
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1 1 04: Extension Timer 2 1-145
FF1 1 04 0001 Hold (0-255) Hold Hold Recall Start Timer (Extensions) 120 (seconds) 1-145
FF1 1 04 0002 Hold (0-255) Hold Hold Recall Start Timer (Attendant Group) 20 (seconds) 1-145
FF1 1 04 0003 Hold (0-255) Hold Hold Recall Start Timer (SLTs) 0 (No recall) 1-146
FF1 1 04 0004 Hold (0-255) Hold Transfer Recall Start Timer (Extensions/
SLTs)60 (seconds) 1-147
FF1 1 04 0005 Hold (0-255) Hold Transfer Recall Start Timer (Attendant 
Group)20 (seconds) 1-147
FF1 1 04 0006 Hold (0-255) Hold Hold/Transfer Recall Ringing Duration Timer 60 (seconds) 1-148
FF1 1 04 0007 Hold (0-255) Hold Attendant Reversion Duration Timer 0 (continue ring) 1-148
FF1 1 04 0008 Hold (0-255) Hold Call Forward/No Answer Timer (Day1) 16 (seconds) 1-149
FF1 1 04 0009 Hold (0-255) Hold Call Forward/No Answer Timer (Day2) 16 (seconds) 1-149
FF1 1 04 0010 Hold (0-255) Hold Call Forward/No Answer Timer (Night) 16 (seconds) 1-150
FF1 1 04 0011 Hold (0-255) Hold Callback Ring Timer (Callback Request and 
Trunk Queuing)15 (seconds) 1-150
FF1 1 04 0012 Hold (0-255) Hold Timed Reminder Ring Timer 16 (seconds) 1-151
FF1 1 04 0013 Hold (0-255) Hold Timed Reminder Interval for Busy 
Extensions180 (seconds) 1-152
FF1 1 04 0014 Hold
FF1 1 04 0015 HoldNot Used -- 1-152
FF1 1 04 0016 Hold (0-255) Hold Howler Tone Duration Timer (Extensions) 30 (seconds) 1-153
FF1 1 04 0017 Hold (0-255) Hold Station Call Park Recall Timer 180 (seconds) 1-153
FF1 2: Dial Plan1-154
FF1 2 01 (0001-0024) Hold (1-4) Hold Maximum/Minimum Dialing at Intercom Dial 
ToneSee table, page 
1-1541-154
FF1 2 02 (0001-0056) Hold (max. 4-digit 
Code) HoldDial Plan A: Flexible Feature Codes at Dial 
ToneSee table, page 
1-1551-155
FF1 2 03 (0001-0056) Hold (max. 4-digit 
Code) HoldDial Plan B: Flexible Feature Codes at Dial 
ToneSee table, page 
1-1571-157
FF1 2 04 (0001-0010) Hold (1-digit Code) 
HoldDial Plan A: Flexible Feature Codes at 
Ringback ToneSee table, page 
1-1591-159
FF1 2 05 (0001-0010) Hold (1-digit Code) 
HoldDial Plan B: Flexible Feature Codes at 
Ringback ToneSee table, page 
1-1601-160
FF1 2 06 (0001-0010) Hold (1-digit Code) 
HoldDial Plan A: Flexible Feature Codes at Busy 
ToneSee table, page 
1-1611-161
FF1 2 07 (0001-0010) Hold (1-digit Code) 
HoldDial Plan B: Flexible Feature Codes at Busy 
ToneSee table, page 
1-1621-162
FF1 3: MCO Access in Tenant Groups1-163
FF1 3 01 (0001-0360) Hold (0-99 or 0-72) 
HoldTenant Group MCO Access: Outbound 
Trunk GroupsSee table, page 
1-1641-164
FF1 3 02 (0001-0360) Hold (0-99) Hold Advanced Routing: Outbound Trunk Group 
Chains0 (none) 1-165
FF1 3 03 (0001-0072) Hold (1-99) Hold MCO Trunk Groups (Inbound Calls) See table, page 
1-1661-166
FF1 4: DID/DNIS Tables1-168
FF1 4 01 0001 Hold (1-4) Hold DID/DNIS Numbering (“A” Side) 4 (digits) 1-168
FF1 4 02 (000-575) (1-6) Hold (0-9999 or 1-
72) HoldDID/DNIS Dial Table (“A” Side) 0 (none) 1-169
FF1 4 03 0001 Hold (1-4) Hold DID/DNIS Numbering (“B” Side) 4 (digits) 1-170
    Add page 70 to Favourites
    image text
    Enable zoom 
    							FF1: System Programming Section 400-Programming
Page 1-8
     l     DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1 4 04 (000-575) (1-6) Hold (0-9999 or 1-
72) HoldDID/DNIS Dial Table (“B” Side) 0 (none) 1-171
FF1 4 05 (0001-0192) Hold (setting) Hold DID Dialing to ISDN “S” Point -- 1-172
FF1 4 06 0001 Hold (0-3) Hold 3rd-party VM: DID Number Automatic Send 0 (do not send 
DID No.)1-174
FF1 4 06 0002 Hold (up to 8 char.) Hold 3rd-party VM: ID Code Prefix for DID (none) 1-174
FF1 4 06 0003 Hold (up to 8 char.) Hold 3rd-party VM: ID Code Suffix for DID (none) 1-175
FF1 5: Not Used1-175
FF1 6: Not Used1-175
FF1 7: Not Used1-175
FF1 8: Digital Pad Settings1-176
FF1 8 01 (0001-0240) Hold (0-31) Hold Digital Pad Settings for Extension Pad Class See table, page 
1-1761-176
FF1 8 02 (0001-0480) Hold (0-31) Hold Digital Pad Settings for Trunk Pad Class See tables, page 
1-179 and 1-180 1-178
FF1 8 03 (0001-0008) Hold (0-31) Hold Digital Pad Settings for BGM See table, page 
1-1811-181
FF1 8 04 (0001-0024) Hold (0-31) Hold Digital Pad Settings for Paging Port Adapter See table, page 
1-1821-182
FF1 8 05 (0001-0024) Hold (0-31) Hold Digital Pad Settings for 3-Party Conference See table, page 
1-1841-183
FF1 8 06 (0001-0024) Hold (0-31) Hold Digital Pad Settings for 8-Party Conference See table, page 
1-1851-185
    All Panasonic manuals Comments (0)

    Related Manuals for Panasonic Digital Business System 576 Technical Manual Section 400 Programming