NEC Neax 2000 Ivs2 Ccis System Manual

							 NEAX2000 IVS2 CCIS System ManualPage 248  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk to Trunk Restriction-CCIS
Programming
DESCRIPTION DATA
Assign the Trunk Restriction Class to the 
required trunk route.
(1)
(2)YY=97
00-63: Route No.
XZ
X: 1-8 : Day Class
Z: 1-8 : Night Class
1: Unrestricted (RCA)
2: Non-Restricted 1 (RCB)
3: Non-Restricted 2 (RCC)
4: Semi-Restricted 1 (RCE)
5: Semi-Restricted 2 (RCE)
6: Restricted 1 (RCF)
7: Restricted 2 (RCG)
8: Fully-Restricted (RCH)
Assign the Area Code Development 
Pattern number to the required trunk route.
(1)
(2)YY=76
00-63: Trunk Route No.
0-7: Area Code Development Pattern 
No. 0-7START
CM35
A 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk to Trunk Restriction-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 249
DESCRIPTION DATA
Assign the Toll Restriction Patterns with 
eight kinds of Trunk Restriction Classes 
assigned by CM35 YY=97. Toll Restriction 
Pattern 00-15 have already been 
programmed as shown below. If a new 
Restriction Pattern is required, change the 
data for Restriction Patterns 01-13 (00, 14 
and 15 are fixed).
(1)
(2)YY=01-13 
Toll Restriction Pattern No. 01-13
1-8: Trunk Restriction Class
0: Restricted
3: Allowed
Specify the maximum number of digits 
dialed by the calling party. The maximum 
number of digits including the area codes 
should be assigned to each area code.
(1)
(2)Y=0-7 
Area Code Development Pattern No. 0-
7 assigned by CM8A YYYY=A000
X-X...X: Area Code dialed 
(Max. 8 digits)
01-24 : 1-24 digits
25-79 : 25-79 digits
CM85
CM81
A
B
0: Restricted
3: AllowedTRUNK
RESTRICTION
CLASSYY
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00
TOLL RESTRICTION PATTERN NUMBER ON EACH TRUNK RESTRICTION CLASS
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00
1 RCA 3033300033333030
2 RCB 3033000033000030
3 RCC 3030000030000030
4 RCD 3000000000000030
5 RCE 3000000000000030
6 RCF 0000000000000030
7 RCG 0000000000000030
8 RCH 0000000000000030 
						

							 NEAX2000 IVS2 CCIS System ManualPage 250  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk to Trunk Restriction-CCIS
DESCRIPTION DATA
Assign the area code to be restricted and 
the Toll Restriction Pattern number 
assigned by CM81 to the Area Code 
Development Pattern number assigned by 
CM35 YY=76. For example, to provide the 
Trunk Restriction Class RCB, RCC, RCD, 
RCE, RCF, RCG and RCH with the Toll 
Restriction for Area Code “00”:
Area Code=00
Toll Restriction Pattern=05
(See Toll Restriction Pattern Table on 
CM81.)
If the Toll Restriction Pattern for the same 
area code is changed according to the 
Tenant, Date, and Time, add the required 
patterns (Tenant, Date, and Time) to the 
area code.
(1)
(2)YYYY=4000-4007 
Area Code Development No. 0-7
X-X...X: Area Code (Max. 8 digits)
B000-B015: Toll Restriction Pattern 
00-15
CM8A
B
C
2000 
-2007
3000 
-3003
0000 
-0255
1000 
-1015
5000 
-5255
Area 
Code4000 
-4004Time 
Pa t te r n
Tenant 
Patter n
Route 
Patter n
Data 
Pattern
TR 
Patter n Toll Restriction 
Pattern 00-15 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk to Trunk Restriction-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 251
DESCRIPTION DATA
To add the Tenant Pattern:
STEP 1 Assign the area code to be 
restricted and the Tenant 
Pattern number to the Area 
Code Development Pattern 
number assigned by CM35 
YY=76.
STEP 2  Assign the Tenant number and 
the Route Pattern number to 
Tenant Pattern number 
assigned by Step 1.
STEP 3  Assign the TR Pattern number 
to Route Pattern number 
assigned by Step 2.
STEP 4  Assign the Toll Restriction 
Pattern number assigned by 
CM81 to TR Pattern number 
assigned by Step 3.
(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)YYYY=4000-4007 
Area Code Development Pattern No.
X-X...X: Area Code (Max. 8 digits)
1000-1015: Tenant Pattern No. 00-15
YYYY=1000-1015 Tenant Pattern No. 
00-15
00-63: Tenant No. 00-63
0000-0255: Route Pattern No. 000-255
YYYY=0000-0255 
Route Pattern No. 000-255
1
XXX 00 (TR Pattern No.)
XXX: 000-255: TR Pattern No. 
YYYY=5000-5255 TR Pattern No.
000
00-15 : Toll Restriction Pattern No. 0-
15
To add the Time and Date Pattern:
STEP 1 Assign the area code to be 
restricted and the Date Pattern 
number to the Area Code 
Development Pattern number 
assigned by CM35 YY=76.
STEP 2  Assign a date to applied to Toll 
Restriction and Time Pattern 
number 0-7 to the Date Pattern 
number assigned by Step 1.
Set the data for all dates, one 
by one, to be applied Toll 
Restriction.
(1)
(2)

(1)
(2)YYYY=4000-4007
X-X...X: Area Code (Max. 8 digits)
3000-3003: Date Pattern No. 0-3
YYYY=3000-3003 Date Pattern No. 0-3
0-6 (Date)
0: Sunday
1: Monday
2: Tuesday
3: Wednesday
4: Thursday
5: Friday
6: Saturday
2000-2007: Time Pattern No. 0-7
CM8A
C
D 
						

							 NEAX2000 IVS2 CCIS System ManualPage 252  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk to Trunk Restriction-CCIS
DESCRIPTION DATA
STEP 3  Assign the starting time for the 
Toll Restriction and Route 
Pattern number to the Time 
Pattern number assigned by 
Step 2. Set the Starting Time as 
shown below.
Example:To Set the 7:00 AM to 9:00 PM 
for the Toll Restriction, enter the 
following starting times one by 
one.
0700 (7:00 AM-7:30 AM)
0730 (7:30 AM-8:00 AM)
0800 (8:00 AM-8:30 AM)
2030 (8:30 AM-9:00 AM)
(1)
(2)YYYY=2000-2007 Time Pattern No. 
00-07
XX ZZ (Starting Time)
XX: 00-23 (Hours)
ZZ: 00/30 (Minutes)
0000-0255
(Route Pattern No. 000-255)
If Tenant Pattern is required, set 1000-1015 
(Tenant Pattern No. 00-15).
STEP 4  Assign the TR Pattern number 
to the Route Pattern number 
assigned by Step 3.
STEP 5  Assign the Toll Restriction 
pattern number (assigned by 
CM81) to TR Pattern number 
assigned by Step 4.
(1)
(2)

(1)
(2)Y=0000-0255 
Route Pattern No.000-255
1
XXX 00 (TR Pattern No.)
XXX: 000-255: TR Pattern No. 
Y=5000-5255 TR Pattern No. 000-255
000
00-15 : Toll Restriction Pattern No. 00-
15
END
CM8A
D
... 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk to Trunk Restriction-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 253
When changing the initial setting (See NOTE on next page.), or when receiving the IMX Trunk
Restriction Class (0-15), execute the following programming.
DESCRIPTION DATA
Assign the IMX Trunk Restriction Class to 
each PBX Trunk Restriction Class for the 
restriction class conversion from the PBX 
to IMX, if required.(1)
(2)20: TRK Restriction Class 1 (RCA)
21: TRK Restriction Class 2 (RCB)
22: TRK Restriction Class 3 (RCC)
23: TRK Restriction Class 4 (RCD)
24: TRK Restriction Class 5 (RCE)
25: TRK Restriction Class 6 (RCF)
26: TRK Restriction Class 7 (RCG)
27: TRK Restriction Class 8 (RCH)
00-15: IMX TRK Restriction Class 
(0-15)
Assign the PBX Trunk Restriction Class to 
each IMX Trunk Restriction Class for the 
restriction class conversion from IMX to 
PBX, if required.(1)
(2)30: TRK Restriction Class 0
31: TRK Restriction Class 1
32: TRK Restriction Class 2
33: TRK Restriction Class 3
34: TRK Restriction Class 4
35: TRK Restriction Class 5
36: TRK Restriction Class 6
37: TRK Restriction Class 7
38: TRK Restriction Class 8
39: TRK Restriction Class 9
40: TRK Restriction Class 10
41: TRK Restriction Class 11
42: TRK Restriction Class 12
43: TRK Restriction Class 13
44: TRK Restriction Class 14
45: TRK Restriction Class 15
01-08: PBX TRK Restriction Class 
(1-8)START
END
CM42 
						

							 NEAX2000 IVS2 CCIS System ManualPage 254  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Trunk to Trunk Restriction-CCIS
NOTE:If no data is set, the initial setting is shown below.
(1) PBX to IMX
(2) IMX to PBX
Operating Procedure
No manual operation is required.
1S T DATA 2ND DATA
20: TRK Restriction Class 1 (RCA)
21: TRK Restriction Class 2 (RCB)
22: TRK Restriction Class 3 (RCC)
23: TRK Restriction Class 4 (RCD)
24: TRK Restriction Class 5 (RCE)
25: TRK Restriction Class 6 (RCF)
26: TRK Restriction Class 7 (RCG)
27: TRK Restriction Class 8 (RCH)01: TRK Restriction Class 1
02: TRK Restriction Class 2
03: TRK Restriction Class 3
04: TRK Restriction Class 4
05: TRK Restriction Class 5
06: TRK Restriction Class 6
07: TRK Restriction Class 7
08: TRK Restriction Class 8
1S T DATA 2ND DATA
30: TRK Restriction Class 0
31: TRK Restriction Class 1
32: TRK Restriction Class 2
33: TRK Restriction Class 3
34: TRK Restriction Class 4
35: TRK Restriction Class 5
36: TRK Restriction Class 6
37: TRK Restriction Class 7
38-45: TRK Restriction Class 8-1501: TRK Restriction Class 1 (RCA)
01: TRK Restriction Class 1 (RCA)
02:  TRK Restriction Class 2 (RCB)
03:  TRK Restriction Class 3 (RCC)
04:  TRK Restriction Class 4 (RCD)
05:  TRK Restriction Class 5 (RCE)
06:  TRK Restriction Class 6 (RCF)
07:  TRK Restriction Class 7 (RCG)
08:  TRK Restriction Class 8 (RCH) 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Uniform Numbering Plan-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 255
UNIFORM NUMBERING PLAN-CCIS
General Description
In a CCIS network, a Uniform Numbering Plan enables a station user to call any other station in
the network. Two alternative numbering plans are provided. In the first plan, the station user dials
any digits station number from three to eight. The location of the office is identified by the first
one-, or two-digits of the station number. In the second plan, the station user dials a one-, two-,
or three-digit office number and any digit station number from two to eight.
Programming
Refer to “Numbering Plan Assignment”.
Operating Procedure
To call a station at another office using Numbering Plan 1:
(1) Lift the handset; receive dial tone.
(2) Dial the any digit station number three to eight.
(3) The call is routed to another office according to programmed routing information, and the 
called station rings.
(4) The called station answers and the par ties are connected.
To call a station at another office using Numbering Plan 2:
(1) Lift the handset; receive Dial Tone.
(2) Dial the access code for CCIS.
(3) Dial the one-, two-, or three-digit office code and any digit station number from two to eight.
(4) The call is routed to the office designated by the Office Code. The called station rings.
(5) The called station answers and the par ties are connected. 
						

							 NEAX2000 IVS2 CCIS System ManualPage 256  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Voice Call-CCIS
VOICE CALL-CCIS
General Description
This feature provides a voice path, through the CCIS network, between a Dterm in one office and
a D
term in another office. This path is established from the calling party to the called party’s built-
in speaker. If the called party’s “MIC” is on, the called party can converse hands-free.
Programming
Operating Procedure
From a Dterm to another Dterm:
(1) The originating D
term user dials the desired station number in a different office and receives 
ring back tone.
(2) Calling party presses the VCL feature/line key. 
A signal tone is transmitted over the CCIS network to the called party’s speaker. 
The calling party’s LCD displays:
(3) The called party presses “MIC” key and dials “1” (if the MIC LED is not on) to allow two-way 
conversation with the calling party.
DESCRIPTION DATA
Assign a Voice Call key to the D
term.
(1)
(2)YY=00
My Line No. +   + Key No.
F1002: Voice Call
START
END
CM90,
VCL          XXXX
(TIME DISPLAY)
Called Dterm
Dterm Series III (Dterm 65) Dterm Series E (Dterm 75)
VOICE CALL    XXXX
(TIME DISPLAY) 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Voice Mail Integration-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 257
VOICE MAIL INTEGRATION-CCIS
General Description
This feature allows any station user in the CCIS network to utilize the Voice Mail System (VMS)
with the Message Center Interface (MCI).
Programming
Refer to Feature Programming Manual.