NEC Neax 2000 Ivs2 Ccis System Manual

							 NEAX2000 IVS2 CCIS System ManualPage 208  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
House Phone-CCIS
Operating Procedure
To call an Attendant in another office:
(1) House Phone-CCIS user lifts the handset.
(2) The Attendant in another office is automatically called. ATND lamps on Attendant Console 
flash and console buzzer sounds. 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Incoming Call Identification-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 209
INCOMING CALL IDENTIFICATION-CCIS
General Description
This feature allows an attendant to visually identify the type of service and/or trunk group which
is arriving or waiting to be answered at the Attendant Console through the CCIS network.
Programming
DESCRIPTION DATA
Specify the ICI key to which an incoming 
call from each trunk route terminates.
(1)
(2)YY=15
00-63: Trunk Route No.
75: No. 7 CCIS Call
Assign the ATT Call Selection keys 
required on the ATTCON.
The following ATT Call Selection keys are 
initially set.
Key No. Data Description
16 F6061 Recall (RCL)
17 F6060 Operator Call
(ATND)
18 F6000 C.O. Incoming 0
(LND0)
(1)
(2)YY=00
ATTCON No. (E000-E007) +   + Key 
No.
F60XX
XX : 00-07: C.O. Incoming Call 0-7
40-47 : Tie Line Incoming Call 0-7
50-53 : Special Operator Call 0-3
54: Priority Call 0
55: Priority Call 1
56: Emergency Call
60: Operator Call
61: Recall
62: Serial Call
63: Call Forwarding Don’t 
Answer (-No Answer)
64: Call Forwarding Busy Line
65: Call Forwarding-Intercept
66: Off Hook Alarm
67: Interposition Calling/
Transfer
Assign the required Attendant Call 
Selection keys and ATTCON Function 
keys to each DESKCON, according to the 
Key label.
(1)
(2)YY=00 
ATTCON No. (E000-E007) +   + Key 
No.
F6000-F6067: Type of Calls to be 
assigned
F6100-F6245: Functions to be 
assigned
CM90 START
CM35
A
07 IO O P 108 IO O P 209 IO O P 310 IO O P 411 IO O P 512 IO O P 6
010203040506
1314
1516
1718
ANS
979091
9293
9495
RLS
96
123
456
789
*0#SRC DEST
HOLD CANCEL
,
, 
						

							 NEAX2000 IVS2 CCIS System ManualPage 210  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Incoming Call Identification-CCIS
Operating Procedure
No manual operation is required.
DESCRIPTION DATA
Key No.
     Data             Description (Key Label)                    Default Data         
13 F6000 C.O. Incoming 0 (LDN) NONE
14 F6040 Tie Line Incoming 0 (TIE) NONE
15 F6064 Call Forwarding-Busy Line (Busy) NONE
16 F6060 Operator Call (ATND) F6061 (Recall)
17 F6063 Call Forwarding-No Answer (NANS) F6060 (Operator Call)
18 F6061 Recall (Recall) F6000 (C.O. Incoming 0)
90 F6200 Source (SRC) F6200 (Source)
91 F6201 Destination (DEST) F6201 (Destination)
93 F6203 Talk (Talk) NONE
94 F6204 Hold (Hold) F6204 (Hold)
95 F6202 Cancel (Cancel) F6202 (Cancel)
96 Answer (Answer)
97 Release (Release)
NOTE:When the DESKCON is used to set H/M features, the Reset key should be 
assigned to one of the feature keys (i.e key 21) in the Idle state mode.
A
END
L6 (12)
L5 (11)
L4 (10)
L3 (09)
L2 (08)
L1 (07) 0 896
3
5 2
1
4
7
#
SRC
(90)DEST
(91) (93) (95)
Answer
(96)
Hold
(94)Release
(97)
Cancel
Talk
Position Busy
VolumeNight(1 5) (01) (02) (03) (04)(13)(16 )(17 )(18 )(1 9) (2 0) (2 1)(14)
(2 4) (22) (23)LDN TIE Busy ATND NANS Recall
EMG BV TRKSL Call Park SC SVCREC
Mute PAGE
Start 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
LDN Night Connection-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 211
LDN NIGHT CONNECTION-CCIS
General Description
This feature routes Listed Directory Number (LDN) calls to a predesignated station in the CCIS
network when the Night Mode has been entered.
Programming
DESCRIPTION DATA
Provide the system with Diversion Display. (1)
(2)204
0: To provide
Specify the Incoming Call Identification 
(ICI) key to which each LDN call from each 
trunk route will terminate.
(1)
(2)YY=15
00-63: Trunk Route No.
00-07: C.O. Incoming Call 0-7
Assign the required number of LDN keys 
as ICI keys.
(1)
(2)YY=00
E00X +   + 13-18 (Key No.)
X: Attendant Console No.
F6000-F6007: LDN0-7
Assign the indialed number to each LDN 
key assigned by CM90. The indialed 
number should be different from any 
numbers assigned by CM10 and CM11.
(1)
(2)YY=01 For DID
0 : Effective data in CM35 Y=15
1-8 : LDN Key No. 00-07 assigned by 
CM46.
X-XXXX: Indialed No.
CM35
CM90
CM50 START
END
CM08
, 
						

							 NEAX2000 IVS2 CCIS System ManualPage 212  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
LDN Night Connection-CCIS
To provide the LDN Diversion feature, the following programming is also required.
DESCRIPTION DATA
Provide the system with the LDN Diversion 
feature.(1)
(2)205
0: To provide
Assign the data for LDN Diversion to each 
indialed number assigned by CM50 
YY=01.
(1)
(2)YY=00 Tenant No. of the LDN
00 : Effective data in CM35 YY=15
01-08 : LDN key No. 00-07 assigned by 
CM90.
00-63 : Tenant No.
Note that a call is diverted to LDN 0-7 keys 
as specified by CM58 YY=02-07, even if 
CM50 YY=01, 1-8 has already been set.
(1)
(2)YY=01 TAS Group No.
Same as CM58 Y=00
00-63: TAS Group No.

(1)
(2)YY=02 Day Mode destination of the 
LDN
Same as CM58 Y=00
00-07 : LDN key 0-7
08 : To TAS
09 : To station/outside party 
assigned by CM58 YY=08.

(1)
(2)YY=03 Night Mode destination
Same as CM58 Y=00
00-07 : LDN key 0-7
08 : To TAS
09 : To station/outside party 
assigned by CM58 YY=09.

(1)
(2)YY=04 Day Mode Diversion for busy 
destination station
Same as CM58 Y=00
00: To ATTCON (BUSY key)
08: To TAS
09: Camped on
CM58 START
CM08
A 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
LDN Night Connection-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 213
DESCRIPTION DATA

(1)
(2)YY=05 Night Mode Diversion for busy 
destination station
Same as CM58 YY=00
Same as CM58 YY=04

(1)
(2)YY=06 Day Mode Diversion for non-an-
swering destination station
Same as CM58 YY=00
00: To ATTCON (NANS key)
08: To TAS

(1)
(2)YY=07 Night Mode Diversion for non-
answering destination station
Same as CM58 YY=00
Same as CM58 YY=06
If the 2nd data (09) is designated by CM58 
YY=02, 03, assign the station/outside par-
ty number to be diverted.
(1)
(2)YY=08 Day Mode destination station/
outside party
Same as CM58 Y=00
X-XXXXXXXX: Station No.
CXX: Abbreviated Code for Outside 
Par ty
XX : 00-31 (Abbreviated Code)

(1)
(2)YY=09 Night Mode destination station/
outside party
Same as CM58 Y=00
X-XXXXXXXX: Station No.
CXX: Abbreviated Code for Outside 
Par ty
XX : 00-31 (Abbreviated Code)
CM58
A
B 
						

							 NEAX2000 IVS2 CCIS System ManualPage 214  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
LDN Night Connection-CCIS
Operating Procedure
No manual operation is required.
DESCRIPTION DATA
If the 2nd data (CXX) is designated by 
CM58 YY=08, 09, specify the combination 
of trunk routes allowing the Tandem 
connection.
(1)
(2)Y=0
XX ZZ
XX: 00-63 (Incoming Trunk Route)
ZZ : 00-63 (Outgoing Trunk Route for 
CCIS)
0: Allow
If the 2nd data (CXX) is designated by 
CM58 YY=08, 09 assign the Speed 
Calling-System (System Speed Dialing) 
memory area exclusively for LDN-Outside.(1)
(2)66: Exclusively for LDN-Outside
XXX ZZZ
XXX: 000-299 (First Memory/SLot No. 
in Block)
ZZZ : 001-300 (No. of Slots to be 
allocated in Block)
Set the stored number to the Memory Slot 
number allocated by CM71.
(1)
(2)Y=0
000-299: Memory Slot No.
XXXX  YY...Y
XX : Access Code (Max. 2 digits)
: Separator Mark
YY...Y : Calling Par ty’s No.
(Max. 26 digits)
CM71
CM72
END
CM36
B
,
, 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Link Alarm Display-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 215
LINK ALARM DISPLAY-CCIS
General Description
This feature provides an indication on external equipment when the CCIS link is connected/
disconnected, when the system is initialized or when the CCH is in make busy.
Programming
Hardware Required
DK card × 1/External Equipment Interface on the MP card
External Indicator (Bell, Lamp etc.)
provided by the customer
For the cross connection of External Indicator, refer to Installation Procedure Manual.
Operating Procedure
No manual operation is required.
DESCRIPTION DATA
Assign the DK card to the required LEN.
NOTE:The DK card number must be 
assigned to the 1st LEN (Level 
0), the 3rd LEN (Level 2) of each 
LT  s l o t .(1)
(2)000-763: LEN
E800-E831: DK Card No.
For PIM0/PIM1: E800-E807
For PIM2/PIM3: E808-E815
For PIM4/PIM5: E816-E823
For PIM6/PIM7: E824-E831
NOTE:Circuit No. 3 of E831 is used 
for built-in External 
Equipment Interface of MP 
card by setting CM44.
Assign the function of CCIS Link Alarm 
Indication to the DK.(1)
(2)XX Y
XX : 00-31 (Card No. assigned by 
CM10>E800-E831)
Y : 0-3 (Circuit No.)
313 : Built-in External Equipment 
Interface on MP card
35 XX
XX: 01-07 (CCIS CH No.)
CM44 START
END
CM10 
						

							 NEAX2000 IVS2 CCIS System ManualPage 216  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Message Waiting Lamp Setting-Attendant-CCIS
MESSAGE WAITING LAMP SETTING-ATTENDANT-CCIS
General Description
This feature allows an attendant, in the IMX system, to set or cancel a Message Waiting lamp
indication, through the CCIS network on a station in a PBX system.
Programming
Hardware Required
To provide a Single-Line Telephone with Message Waiting lamp:
LC (PN-4LCD/4LCF) card
Operating Procedure
To set a Message Waiting indication from the IMX ATTCON:
(1) Press an idle LOOP key; receive dial tone.
(2) Dial the Message Waiting feature access code (max. three digits); receive feature dial tone.
(3) Dial the station number; receive service set tone.
(4) Message Waiting indication is set.
(5) Press the RELEASE key to return to an idle condition.
To cancel a Message Waiting indication:
(1) Press an idle LOOP key; receive dial tone.
(2) Dial the Message Waiting cancel code (max. 3 digits); receive feature dial tone.
(3) Dial the station number; receive service set tone.
(4) Message Waiting indication is canceled.
(5) Press the CANCL key to return to an idle condition.
DESCRIPTION DATA
Provide each station with Message Wait-
ing service.
(1)
(2)YY=03
X-XXXXXXXX: Station No.
0: To provideSTART
END
CM13 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Message Waiting Lamp Setting-Station-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 217
MESSAGE WAITING LAMP SETTING-STATION-CCIS
General Description
This feature allows a station user in the IMX system to set or cancel a Message Waiting lamp
indication, through the CCIS network, to a station in the PBX system with this feature.
Programming
Hardware Required
To provide a Single-Line Telephone with Message Waiting lamp:
LC (PN-4LCD/4LCF) card
Operating Procedure
To set a Message Waiting indication:
(1) Lift the handset; receive dial tone.
(2) Dial the Message Waiting feature access code (up to 3 digits); receive feature dial tone.
(3) Dial the desired station number; receive service set tone.
(4) Message Waiting indication is set at the station.
To cancel a Message Waiting indication:
(1) Lift the handset; receive dial tone.
(2) Dial the Message Waiting cancellation code (up to 3 digits); receive feature dial tone.
(3) Dial the desired station number; receive service set tone.
(4) Message Waiting indication at station is canceled.
DESCRIPTION DATA
Provide each station with Message Wait-
ing service.
(1)
(2)Y=03
X-XXXXXXXX: Station No.
0: To provideSTART
END
CM13