NEC Neax 2000 Ivs2 Ccis System Manual
Have a look at the manual NEC Neax 2000 Ivs2 Ccis System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NEAX2000 IVS2 CCIS System ManualPage 238 ND-70918 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING Trunk Answer From Any Station-CCIS TRUNK ANSWER FROM ANY STATION-CCIS General Description This feature allows any station, not restricted from incoming calls, to answer incoming calls when the network is in Night Mode. When this feature is activated, incoming exchange network calls will activate a common aler t Trunk Answer From Any Station (TAS) signal at the customer premises. By dialing a specified code, any station in the local PBX may answer the call and extend it to any other station in the CCIS network using Call Transfer-All Calls-CCIS. Programming SATELLITE OFFICE TA S NO. 7CCISMAIN OFFICE COT/DIDCO PBX PBX/IMX The Main Office sends dial code as LDN number to the Satellite Office
CHAPTER 3 SYSTEM DATA PROGRAMMING Trunk Answer From Any Station-CCIS NEAX2000 IVS2 CCIS System Manual ND-70918 (E), Issue 1.0 Page 239 For the Satellite Office Use the LDN Diversion feature. DESCRIPTION DATA Assign a Trunk Restriction Class to each station. (1) (2)YY=01 X-XXXXXXXX: Station No. XZ Z: 1-8: Trunk Restriction Class in Night Mode 1: Unrestricted (RCA) 2: Non-Restricted 1 (RCB) 3: Non-Restricted 2 (RCC) 4: Semi-Restricted 1 (RCD) 5: Semi-Restricted 2 (RCE) 6: Restricted 1 (RCF) 7: Restricted 2 (RCG) 8: Fully-Restricted (RCH) Assign the Service Restriction Class B to the required stations. (1) (2)YY=02 X-XXXXXXXX: Station No. XX ZZ ZZ: 00-15 : Service Restriction Class B Allow Trunk Answer From Any Station in the Service Restriction Class B assigned by CM12 YY=02. (1) (2)YY=53 00-15: Service Restriction Class B assigned by CM12 YY=02 1 : Allow Provide the system with the Diversion Display and the LDN Diversion features.(1) (2)204: Diversion Display 0: To provide (1) (2)205: LDN Diversion 0: To provide Assign the indialed number to each TIE key on the ATTCON. But, the ATTCON should not be equipped in the Satellite Office. The indialed number should be different from any numbers assigned by CM10 and CM11. (1) (2)YY=02 1-8: TIE key No. X-XXXX: Indialed No.START CM12 A CM15 CM08 CM50
NEAX2000 IVS2 CCIS System ManualPage 240 ND-70918 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING Trunk Answer From Any Station-CCIS DESCRIPTION DATA Assign the data for LDN Diversion to each indialed number assigned by CM50 YY=02. (1) (2)YY=00 Tenant No. of the LDN 01-08: TIE 0-7 assigned by CM50 YY=02 00-63: Tenant No. (1) (2)YY=01 TAS Group No. Same as CM58 Y=00 00-63: TAS Group No. (1) (2)YY=02 Day Mode Destination Same as CM58 Y=00 08: To TAS (1) (2)YY=03 Night Mode Destination Same as CM58 Y=00 08: To TAS Specify the function of each type of TAS within a system. (1) (2) (1) (2)Y=0-4 TAS Answer A-E 1: Tie Line/Dial-in 0 : Cannot be answered 1 : Can be answered 7: A call terminated to a different tenant 0 : Can be answered 1 : Cannot be answered Assign the access code for each type of TAS (TAS Answer A-E) assigned by CM53. (1) (2)Y=0-3 Numbering Plan Group 0-3 X-XXXX: Access Code A047: TAS Answer A A048: TAS Answer B A049: TAS Answer C A050: TAS Answer D A051: TAS Answer E CM58 A CM53 CM20 B (1) Y17 0TA S Answer A0/1 0/1 1TA S Answer B0/1 0/1 2TA S Answer C0/1 0/1 3TA S Answer D0/1 0/1 4TA S Answer E0/1 0/1
CHAPTER 3 SYSTEM DATA PROGRAMMING Trunk Answer From Any Station-CCIS NEAX2000 IVS2 CCIS System Manual ND-70918 (E), Issue 1.0 Page 241 DESCRIPTION DATA Specify the tenants allowing TAS Answer between them. (1) (2)Y=0 XX ZZ XX: 00-63 (Tenant No. of TAS Answer station) ZZ: 00-63 (Tenant No. of Trunk) 0 : Allow 1: RestrictedB END CM63
NEAX2000 IVS2 CCIS System ManualPage 242 ND-70918 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING Trunk Answer From Any Station-CCIS To provide an External TAS Indicator via the DK card: DESCRIPTION DATA Assign the card number of the to required LEN. NOTE:The DK card number must be as- signed to the 1st LEN (Level 0), the 3rd LEN (Level 2) of each LT slot.(1) (2)000-763: LEN E800-E831: DK Card No. For PIM0/1: EB800-EB807 For PIM2/3: EB808-EB815 For PIM4/5: EB816-EB823 For PIM6/7: EB824-EB831 Assign the TAS Group number assigned by CM30 YY=17 to a circuit number on the DK card. NOTE:Built-in External Equipment Interface is not available for External TAS indicator connection.(1) (2)XX Y: Circuit No. XX : 00-31: DK Card No. assigned by CM10 E800-E831 Y : 0-3: Circuit No. 313 : Built-in External Equipment Interface on MP card 13 XX XX: 00-63 (TAS Group No. assigned by CM30 YY=17) Specify the indication pattern for the External TAS Indicator.(1) (2)00 01: 30 IPM 02: 60 IPM 03: 120 IPM 07: Steady on NONE : 120 IPM (0.25 sec. ON/OFF) CM59 START CM10 END CM44
CHAPTER 3 SYSTEM DATA PROGRAMMING Trunk Answer From Any Station-CCIS NEAX2000 IVS2 CCIS System Manual ND-70918 (E), Issue 1.0 Page 243 To provide the telephone set for TAS Indication: DESCRIPTION DATA Assign the TAS Buzzer number (telephone set for TAS Indication) to the required LEN. The TAS Buzzer number must correspond with the TAS Group number assigned by CM30 YY=17. E600-E663 TAS Group 00-63(1) (2)000-763: LEN E600-E663: TAS Buzzer No.START CM10 END
NEAX2000 IVS2 CCIS System ManualPage 244 ND-70918 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING Trunk Answer From Any Station-CCIS For Main Office COT: When using a COT interface between the Central Office and a Main Office, set up programming to the Main Office by using the DIT-CCIS feature, and send the dial code as an LDN to the Satellite Office. Refer to programming of DIT-CCIS in this chapter for details. DID: When using a DID interface between the Central Office and the Main Office, there are two programming patterns: Pattern 1 When an incoming LDN call is diverted to a Satellite Office in both Day Mode and Night Mode, program by using the LCR and uniform numbering features. Refer to Numbering Plan Assignment. Pattern 2 When an incoming LDN call is diverted to a Satellite Office in either Day Mode or Night Mode (not both), the following programming for the LDN Diversion-Outside feature is required. DESCRIPTION DATA Provide the system with the Diversion Display and the LDN Diversion features.(1) (2)204: Diversion Display 0: To provide (1) (2)205: LDN Diversion 0: To provide Assign the indialed number to each TIE key on the ATTCON. The indialed number should be different from any numbers assigned by CM10 and CM11. (1) (2)YY=01 1-8: LDN key No. X-XXXX: Indialed No. Assign the data for LDN Diversion to each indialed number assigned by CM50 YY=01. (1) (2)YY=00 Tenant No. 01-08: LDN 0-7 assigned by CM50 YY=01 00-63: TAS Group (1) (2)YY=02 Day Mode Destination 01-08: LDN 0-7 assigned by CM50 YY=01 09: LDN Diversion-Outside (Assigned by CM58 YY=08) CM50 CM58 START CM08 A
CHAPTER 3 SYSTEM DATA PROGRAMMING Trunk Answer From Any Station-CCIS NEAX2000 IVS2 CCIS System Manual ND-70918 (E), Issue 1.0 Page 245 DESCRIPTION DATA (1) (2)YY=03 Night Mode Destination Same as CM58 YY=02 09: LDN Diversion-Outside (Assigned by CM58 YY=09) Assign the Abbreviated Code for System Speed Dialing to terminate the Satellite Office via CCIS by DID in Day Mode and Night Mode, respectively. (1) (2)YY=08 Day Mode YY=09 Night Mode Same as CM58 YY=02 CXX XX: Abbreviated Code for System Speed Dialing Assigned by CM71>66 Assign the System Speed Dialing memory area exclusively for LDN Diversion- Outside.(1) (2)66: Exclusively for LDN Diversion- Outside XXX YYY XXX: 000-299 (First Memory/Slot No. in Block) YYY: 001-300 (No. of Slots to be allocated in Block) Set the stored number into the Memory Slot number allocated by CM71.(1) (2)000-299: Memory Slot No. XX YY...Y XX : Access Code (Max. 2 digits) : Separator Mark YY...Y : Calling Par ty’s No. (Max. 26 digits) Specify the combination of Trunk Routes allowing a Tandem connection. (1) (2)Y=0 XX ZZ XX: 00-63 (Incoming Trunk Route) ZZ : 00-63 (Outgoing Trunk Route for CCIS) 0: Allow END CM58 A CM71 CM72 CM36, ,
NEAX2000 IVS2 CCIS System ManualPage 246 ND-70918 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING Trunk Answer From Any Station-CCIS Hardware Required To provide the External TAS Indicator: - DK card (Four Indicators per card can be equipped) - Indicator Requirement to External Indicator Control Method : Loop/Ground/Battery (-27 V) (Max. 125 mA) Type : Visual and/or Audible type with volume control For cross connection of the TAS indicator, refer to the Installation Procedure Manual. To provide the telephone set for TAS Indication: - PN-4LC card (Two telephone sets per card can be equipped.) - Conventional telephone sets Operating Procedure To answer an incoming call in Night Mode: (1) The TAS signal (bell, buzzer, etc.) sounds indicating an incoming call. (2) Lift the handset; receive dial tone. (3) Dial the TAS access code. (4) Connect to the incoming call.
CHAPTER 3 SYSTEM DATA PROGRAMMING Trunk to Trunk Restriction-CCIS NEAX2000 IVS2 CCIS System Manual ND-70918 (E), Issue 1.0 Page 247 TRUNK TO TRUNK RESTRICTION-CCIS General Description This feature allows trunk to trunk tandem restriction by caller’s information (e.g., caller is a trunk) through the CCIS network. Case 1: A tandem connection at the following office can be restricted by Trunk Restriction Class of Trunk A and Outgoing Connection Restriction data of Trunk B. Case 2: When Station B transfers an incoming call through CCIS to Trunk C, a trunk-to-trunk connection can be restricted by Trunk Restriction Class of Trunk A and Outgoing Connection Restriction data of Trunk C. INCOMING TRUNK Trunk A Office BOffice AOUTGOING TRUNK Trunk B CCIS INCOMING TRUNK Trunk A Office BOffice A Station B CCIS Trunk C Transfer by CONSULTATION HOLD