NEC Neax 2000 Ivs2 Ccis System Manual

							 NEAX2000 IVS2 CCIS System ManualPage 218  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Miscellaneous Trunk Access-CCIS
MISCELLANEOUS TRUNK ACCESS-CCIS
General Description
This feature provides access to all types of external and customer-provided equipment/facilities,
such as tie lines and exchange networks, along with Dictation, Paging Access-CCIS, and Code
Calling through the CCIS network.
Programming
Refer to Numbering Plan Assignment and assign the trunk access code using the LCR feature.
Operating Procedure
No manual operation is required. 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Miscellaneous Trunk Restriction-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 219
MISCELLANEOUS TRUNK RESTRICTION-CCIS
General Description
This feature denies certain stations and dial-repeating tie trunks access to particular trunk
groups, such as tie lines, exchange networks, Dictation, or Paging Access-CCIS through the
CCIS network.
Programming
Assign “1” (Restricted) as the 2nd Data of CM36 when programming the Deluxe Traveling Class
Mark-CCIS on Page 188.
Operating Procedure
No manual operation is required. 
						

							 NEAX2000 IVS2 CCIS System ManualPage 220  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Night Connection-Fixed-CCIS
NIGHT CONNECTION-FIXED-CCIS
General Description
When the Night Mode has been entered, this service feature routes calls normally directed to the
Attendant Console to a preselected station in another office, through the CCIS network.
Programming
Refer to Direct-In Termination-CCIS on Page 194.
Operating Procedure
To answer a Night Connection-Fixed-CCIS call.
(1) An incoming call to the Attendant Console in Night Mode is automatically transferred to a 
preselected Night Connection station belonging to a different office.
(2) The calling party hears ring back tone.
(3) Ring signal is sent to the Night Connection station.
(4) The Night Connection station goes off-hook to answer the incoming call. 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Night Connection-Flexible-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 221
NIGHT CONNECTION-FLEXIBLE-CCIS
General Description
This feature provides an inter-office Night Connection service, via the CCIS network, when the
calling station and the Night station belong to different offices.
Programming
Refer to Direct-In Termination-CCIS on Page 194.
Operating Procedure
To set the Night Connection-Flexible-CCIS:
(1) The operator or Night Fixed-station user in the destination office sets Call Forwarding-All 
Calls-CCIS to a station in another office.
To answer Night Connection-Flexible-CCIS calls:
(1) In the Night Mode, incoming calls to the Attendant Console are automatically transferred to 
a preselected Night Connection station belonging to a different office.
(2) The calling party hears ring back tone.
(3) Ring signal is sent to the Night Connection station.
(4) The Night Connection station goes off-hook to answer the incoming call. 
						

							 NEAX2000 IVS2 CCIS System ManualPage 222  ND-70918 (E), Issue 1.0
This page intentionally left blank. 
						

							NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 223
This page intentionally left blank. 
						

							 NEAX2000 IVS2 CCIS System ManualPage 224  ND-70918 (E), Issue 1.0
This page intentionally left blank. 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Outgoing Trunk Queuing-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 225
OUTGOING TRUNK QUEUING-CCIS
General Description
This feature allows a CCIS network station, upon encountering an “all trunks busy” signal, to dial
a specified access code and enter a first-in, first-out queue. As soon as a CCIS trunk becomes
available, stations in the queue will be called back on a first-come, first-served basis.
NOTE:This feature applies to the tie line trunks between the two PBX systems and not to the
outgoing trunks at the remote PBX.
Programming
DESCRIPTION DATA
Assign the Service Restriction Class A to 
the required stations.
(1)
(2)YY=02
X-XXXXXXXX: Station No.
XX ZZ
XX: 00-15 : Service Restriction 
Class A
Allow Outgoing Trunk Queuing in the 
Service Restriction Class A assigned by 
CM12 YY=02.
(1)
(2)YY=02
00-15: Service Restriction Class A as-
signed by CM12 Y=02
1 : Allow
Assign access code for setting and 
resetting this service.
(1)
(2)Y=0-3 Numbering Plan Group 0-3
X-XXXX: Access Code
Different access code from Call Back
A000: Set
A001: Reset
Same access code as Call Back
A004: Set
A005: Reset
Assign the Trunk Queuing-OG (Call Back) 
key to the required D
term.
(1)
(2)YY=00
My Line No. +   + Key No.
F0004
Specify the Trunk Queuing-Outgoing 
capability to each trunk route.
(1)
(2)YY=28
00-63: Trunk Route No.
0: Restricted
1 : Allow
CM15
CM20
CM90 START
CM12
CM35
END
, 
						

							 NEAX2000 IVS2 CCIS System ManualPage 226  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Outgoing Trunk Queuing-CCIS
Operating Procedure
To activate Outgoing Trunk Queuing-CCIS:
(1) Dial the trunk access code; receive dial tone.
(2) Dial the desired number; receive busy tone.
(3) Press the hookswitch momentarily; receive feature dial tone.
(4) Dial the Outgoing Trunk Queuing-CCIS feature access code; receive service set tone.
(5) Replace handset
To cancel Outgoing Trunk Queuing-CCIS:
(1) Dial the Outgoing Trunk Queuing-CCIS cancellation code; receive service set tone. 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Paging Access-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 227
PAGING ACCESS-CCIS
General Description
This feature provides dial access to paging equipment from an Attendant Console or station
through the CCIS network.
Programming
DESCRIPTION DATA
Assign the Paging Trunk (COT card and 
DK card) to the required LEN.
NOTE:The DK card number must be 
assigned to the first LEN (Level 
0) and third LEN (Level 2) of 
each LT slot.(1)
(2)000-763: LEN
D000-D255 : COT card
E800-E831 : DK card
For PIM0/1 : E800-E807
For PIM2/3 : E808-E815
For PIM4/5 : E816-E823
For PIM6/7 : E824-E831
NOTE:Circuit No. 3 of E831 is used 
for built-in External 
Equipment Interface on the 
MP card by setting CM44.
Assign the paging function to the DK card 
or external equipment interface on the MP 
card.(1)
(2)XX Y
XX : 00-31 (DK Card No. assigned by 
CM10 [E800-E831])
Y : 0-3 (Circuit No. of DK card)
313 : Built-in External Equipment 
Interface
02 XX: Speak Paging start
XX: 00-09 (Speaker Paging Zone 0-9)
Specify the conditions for paging access. (1)
(2)094: Paging Access Tone
0 : To send
1 : Not sent out
Assign the access code for paging access.
(1)
(2)Y=0-3 Numbering Plan Group 0-3
X-XXXX: Access Code
100-163: For Paging Access 
(Route 00-63)
CM20 START
CM10
CM44
CM08
A