NEC Neax 2000 Ivs2 Ccis System Manual

							 NEAX2000 IVS2 CCIS System ManualPage 198  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Distinctive Ringing-CCIS
DISTINCTIVE RINGING-CCIS
General Description
This feature provides distinctive station ringing patterns for terminated calls through the CCIS
network so that a station user can distinguish between incoming internal and external calls.
Programming
Operating Procedure
No manual operation is required.
DESCRIPTION DATA
Select the ringing pattern on external call.
(1)
(2)YY=33
00-63: Trunk Route No. for IC
0 : 0.4 s ON-0.2 s OFF-0.4 s ON-2 s 
OFF
1 : 0.4 s ON-0.2 s OFF-0.4 s ON-2 s 
OFF
2 : 1 s ON-2 s OFF
3 : When CM08>392: 0
2 s ON-4 s OFF
When CM08>392: 1
0.4 s ON-0.2 s OFF-0.4 s ON-0.2 s 
OFF
RINGING
The ringing pattern should be selected in PBX A (equipped with incoming COT).COT
Internal ringing will always be 1 sec. ON, 2 sec. OFF.
PBX 
BPBX 
A
START
END
CM35 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Do Not Disturb-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 199
DO NOT DISTURB-CCIS
General Description
This feature allows a station user to establish the Do Not Disturb (DND) status on a temporary
basis, during which time access to the station from incoming CCIS calls will be denied.
Programming
DESCRIPTION DATA
Assign the Service Restriction Class A the 
required stations.
(1)
(2)YY=02
X-XXXXXXXX: Station No.
XX ZZ
XX: 00-15 : Service Restriction 
Class A
Allow Do Not Disturb in the Service 
Restriction Class A assigned by CM12 
YY=02.
(1)
(2)YY=19
00-15: Service Restriction Class A 
assigned by CM12 YY=02
1 : Allow
Assign the Do Not Disturb group of 
stations. Do Not Disturb is set 
simultaneously for the stations assigned 
by this command, by operation from the 
Attendant Console.
(1)
(2)YY=00
X-XXXXXXXX: Station No.
0: Provided
Assign the access code for Do Not Disturb 
Set/Cancel.
(1)
(2)Y=0-3 Numbering Plan Group 0-3
X-XXXX: Access Code
A022: Set
A023: Cancel
Assign the destination of call transfer when 
the called station is set to Do Not Disturb.
NOTE:Station No. or Attendant No.
must be assigned within this
PBX.
(1)
(2)YY=10
00-63: Tenant No.
X-XXXXXXXX: Station No.
E000: Attendant Console
CM15
CM13
CM20 START
CM12
A
CM51 
						

							 NEAX2000 IVS2 CCIS System ManualPage 200  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Do Not Disturb-CCIS
DESCRIPTION DATA
If the Attendant Console is assigned as the 
destination by CM51, assign a Call 
Forwarding-Intercept (ICPT) key to the 
console.
(1)
(2)YY=00
My Line No. +   + Key No.
F6065: Call Forwarding-Intercept Key
Assign a DND function key to a D
term, if 
desired.
(1)
(2)YY=00
My Line No. +   + Key No.
F0022: Do Not Disturb set/reset
Assign DND and DNDOVR function keys 
to the ATTCON/DESKCON.
(1)
(2)YY=00
ATTCON No. (E000-E007) +   + Key 
No.
F6102: DND
F6103: DND Override
F6104: RESET
Specify the Call Forwarding-Busy Line/
Station Hunting for a station set to Do Not 
Disturb.(1)
(2)240
0 : Available
1 : Not available
For a system with Multiple-Tenant 
features, specify the destination of a call 
transferred in CM51 YY=10 for the tenant 
of the calling or called station.(1)
(2)241
0 : Tenant of called station
1 : Tenant of calling station
Select the Dial Tone on setting Do Not 
Disturb.
(1)
(2)Y=2
14: Dial Tone on setting Do Not Disturb
0 : Special Tone
1 : Dial Tone
CM08
END
CM90
A
CM48,
,
, 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Do Not Disturb-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 201
Operating Procedure
Single-Line Telephone/Dterm
To set Do Not Disturb from a Single-Line Telephone or Dterm:
(1) Lift the handset; receive dial tone.
(2) Dial Do Not Disturb-CCIS feature access code; receive service set tone.
(3) Replace the handset.
To cancel Do Not Disturb from a Single-Line Telephone or D
term:
(1) Lift the handset; receive dial tone.
(2) Dial Do Not Disturb-CCIS cancellation code; receive service set tone.
(3) Replace the handset.
D
term
To set Do Not Disturb-CCIS from a Dterm:
(1) Press the SPEAKER key; receive dial tone.
(2) Press the Do Not Disturb feature access key and the associated LED lights. If equipped with 
an LCD, the display will indicate SET.
(3) Press the SPEAKER key.
To cancel Do Not Disturb-CCIS from a D
term:
(1) Press the SPEAKER key; receive dial tone.
(2) Press the Do Not Disturb feature access key and the associated LED goes out. If equipped 
with an LCD, the display will indicate CNCL.
(3) Press the SPEAKER key. 
						

							 NEAX2000 IVS2 CCIS System ManualPage 202  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Dual Hold-CCIS
DUAL HOLD-CCIS
General Description
This feature allows two connected Dterms to simultaneously be placed on hold over the CCIS link.
This enables the held parties to answer or originate a call from a secondary-line appearance or
the idle prime extension.
Programming
Operating Procedure
To operate Dual Hold-CCIS from a Dterm:
(1) Station A pressed the HOLD key; Station B is placed on hold.
(2) Station B pressed the HOLD key; Station A is placed on hold.
(3) Dual Hold-CCIS is now in progress.
DESCRIPTION DATA
Assign the Service Restriction Class B to 
the required stations.
(1)
(2)YY=02
X-XXXXXXXX: Station No.
XX ZZ
ZZ: 00-15 : Service Restriction 
Class B
Allow Dual Hold in the Service Restriction 
Class B assigned by CM12 YY=02.
(1)
(2)YY=64
00-15: Service Restriction Class B 
assigned by CM12 YY=02.
1 : Allow
CM15 START
END
CM12 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Flexible Numbering of Stations-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 203
FLEXIBLE NUMBERING OF STATIONS-CCIS
General Description
This feature allows voice and data station numbers to be assigned to any instrument in the CCIS
network, based solely upon numbering plan limitations.
PUBLIC 
NETWORK
MAIN OFFICE
4XXXX
51XX
6XXXX6XXXX52XX53XX
TRIBUTARY OFFICE
PUBLIC 
NETWORKSATELLITE OFFICE
Office location is indicated by all digits of the station number 
						

							 NEAX2000 IVS2 CCIS System ManualPage 204  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Flexible Numbering of Stations-CCIS
Programming
Operating Procedure
No manual operation is required.
DESCRIPTION DATA
Assign a Numbering Plan Group to each 
Tenant.(1)
(2)00-63: Tenant No.
710-713: Numbering Plan Group 0-3
Specify the number of digits for station 
numbers.
Example: For setting station number 
“2XXX”
(1) 2
(2) 804
NOTE:To the following stations, 5 or 
more digit station numbers must 
not be assigned if:
Stations are observed by 
SMDR/PMS/OAI
Front Desk Terminal/D
term 
TIMS
(1)
(2)Y=0-3 Numbering Plan Group 0-3
X: 1st digit of station No.
801: 1 digit
802: 2 digits
803: 3 digits
804: 4 digits
805: 5 digits
806: 6 digits
807: 7 digits 
808: 8 digits 
Assign station number to the required LEN 
according to the Numbering Plan specified 
by CM20.(1)
(2)000-763: LEN
X-XXXXXXXX: Station No.
CM20
CM10 START
CM29
END 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
Hot Line-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 205
HOT LINE-CCIS
General Description
This feature allows two stations at different nodes in the CCIS network to be mutually associated
on an automatic ring down basis through the CCIS network.
Programming
Use the Hot Line-Outside feature.
DESCRIPTION DATA
Assign a Hot Line to the required stations.
(1)
(2)YY=03
X-XXXXXXXX: Station No.
04: Hot Line
Allocate memory area Hot Line-Outside 
calls. For example, to assign 10 Hot Line-
Outside calls into No. 100 through No. 109 
Memory Slots, 2nd data is “100010”. 
Abbreviated Codes are automatically 
assigned as shown below:(1)
(2)65: For Hot Line-Outside
XXX ZZZ
XXX: 000-299 (Stating Memory Slot 
No. in blocks)
ZZZ : 001-300 (No. of Memory Slots to 
be assigned in blocks)
Assign the destination party’s number to 
each Memory Slot number.
(1)
(2)Y=0
000-299: Memory Slot No.
XXXX  YY...Y
XX : Access Code (Max. 2 digits)
: Separator Mark
YY...Y : Calling Par ty’s No.
(Max. 26 digits)
Define the Hot Line pairs.
(1)
(2)YY=00-99 Hot Line Pair No.
0: Calling Side
1: Called Outside Side
C XX (for Called Party)
XX: 00-09 (Abbreviated Code given by 
CM71)
CM71
CM72 START
CM12
CM52
AMemory Slot 100
Memory Slot 109
~
Abbrev. Codes
00
09
~
,
, 
						

							 NEAX2000 IVS2 CCIS System ManualPage 206  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Hot Line-CCIS
Operating Procedure
To place a Hot Line-CCIS call:
(1) Station “A” lifts the handset.
(2) Station “B” is rung.
(3) Station “B” lifts the handset and the connection is established.
DESCRIPTION DATA
Specify the result of Switch Hook Flash on 
Hot Line station.
To allow Hot Line stations to transfer a call 
or access a feature, set the data to”0”.(1)
(2)057
0 : Special Dial Tone
1 : Attendant Recall
CM08
A
END 
						

							CHAPTER 3 SYSTEM DATA PROGRAMMING
House Phone-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 207
HOUSE PHONE-CCIS
General Description
This feature allows selected stations to call an Attendant Console through the CCIS network,
simply by going off hook.
Programming
Use the Hot Line-Outside feature.
DESCRIPTION DATA
Assign a Hot Line (House-phone) to the 
required station.
(1)
(2)YY=03
X-XXXXXXXX: Station No.
04: Hot Line (House-phone)
Allocate memory area for Hot Line-
Outside calls. For example, to assign 10 
Hot Line-Outside calls into No. 100 
through No. 109 Memory Slots, 2nd data is 
“100010.” Abbreviated Codes are 
automatically assigned as shown below:(1)
(2)65: For Hot Line-Outside
XXX ZZZ
XXX: 000-299 (Starting Memory Slot 
No. in blocks)
ZZZ : 001-300 (No. of Memory Slots to 
be assigned in blocks)
Assign the destination party’s number to 
each Memory Slot number.
(1)
(2)Y=0
000-299: Memory Slot No.
XXXX  YY...Y
XX : Access Code (Max. 2 digits)
: Separator Mark
YY...Y : Calling Par ty’s No.
(Max. 26 digits)
Define the Hot Line (House-phone) pairs.
(1)
(2)YY=00-99 Hot Line Pair No.
0: Calling Side
X-XXXXXXXX: Virtual Station No.
(1)
(2)1: Called Side
C XX (for Outside p a rty)
XX: 00-09 (Abbreviated Code given by 
CM71)
CM71
CM72
CM52 START
CM12
END
Memory Slot 100
Memory Slot 109
~
Abbrev. Codes
00
09
~
,
,